What did you do to your truck today!

[60ratrod]

removed the drivers rocker since the only welds holding it in were what i put in it. 3 tack welds and a couple cuts later i now have room for the new rocker. i just gotta put it in now

[67Slider]

Bled the new power steering unit. Working flawlessly. I am so stoked that it actually works as good as it does. What a difference it makes in the drive.

[Jeffs70]

I cut some holes in my trailing arm cross member for my exhaust and welded in some 4" pipe to sturdy it up and keep it clean.

[60ratrod]

got my replacement cab support and driver's rocker tacked in place. i'm actually rather impressed with how well this novice body man did!

[FRENCHBLUE72]

Started to weld up the cab seams.

[elf w/capital T]

22nd attempt at getting my signal/brake light issue fixed and changed oil

[gonnuts]

Put in a corvette servo in my 700R4 and took for a drive. 1-2 shift is much better now, not hard by any means but at least I don't have to let up on the pedal when it shifts.

[67c10rustbuket]

I sold my original 283 this morning on craigslist $100 ! good bye, time to clean up that frame, .

[fast50ranger]

Changed the oil. I know that is boring but it had to be done.

[Hard On Parts]

Installed new sending unit from LMC, painted oil dipstick.

[cpisani70@aol.com]

Replaced the ignition cylinder,the dash pad , got it registered, took apart a / the carb for the first time and cleaned out the fuel bowl Now it runs a lot better.
Posted via Mobile Device

[Brewski*]

Opened the hood, hooked up the horn, Honked it to try to get the dog to come home.

[Red68]

I installed a tach kit today. My truck didn't come with a tach originally. Also took it to a show after I cleaned it up.
Posted via Mobile Device

[project 67 sub]

looked at it walked passed it quite a few times while working on my bug, sat a few things on it for a little while while i was working on the bug then took the stuff off when i was finished

[streetroddertim]

Painted the wheels and ordered the baby moons

[wtchop]

cleaned the bed up. need to repair some of it where someone ran exhaust stacks on it sometime in the past.

before



after

[1low]

Finished the clean up on my frame. Off to powder coat

[cppursell]

Not today but yesterday I gave a wash and photo shoot for my truck: http://67-72chevytrucks.com/vboard/s...d.php?t=465927

[Bennett68C10]

Well I finished putting my rear brakes back together and filled my diff with fluid. What a pita it was getting the fill plug out, somebody put a cast plug in for the original, it wouldn't budge so it broke into several different pieces. Had to heat it with a torch to get it out. Then I finished the routing the pipes on my side exhaust where they exit in front of the tires and grinded down all the welds.

[cliff67]

working on the 59 dash install

[ChevLoRay]

Crazy thing about those '59 dashes...as wide as they were, don't you have to narrow it to put it in our trucks? There's a guy near here who put a dash from a '59 Edsel in his '68. He had to widen it to make it fit.

I said that because I remember how wide they seemed to be when they were new. Dad bought a '59 Ford, while my cousin bought a '59 Impala HT. When I started driving, it was on the Ford.

Back in the day, there was some scuttle about having to add marker lights on the fins of the Chevy. Seems it was just under the width limit.

Oh, I like it.

But, on my truck...son and I reattached the engine cross member and the trailing arms. Waiting on the upper/lower control arms so we can get some ball joints and start that phase. But, we worked on it for a change.

[cliff67]

Belive it or not I had to add about 5" to the dash but that could of been from the way it was cut out of the donor car. It was a ebay deal, Next time I will ask for more pic. for sure. I leaarned to drive a stick in an old impala in the driveway .So It will be cool to look at that dash again ! But I have a long way to go to be driving this one

[blazerboy_4life]

I put my stepside box on!

[colin_havens]

Ordered some parts last night, to get my motor really tuned in. Right now its just a little rich lol. Ordered a jet and rod kit for my Edelbrock 650 Thunder series carb, a timing tape, and some distributer advance weights and springs for the MSD HEI on my motor, oh and a vaccum gauge. Hope to lean out the idle so your eyes dont water when you stand beside it, and get some better gas mileage and get rid of the bog down when I put my foot to the floor. Gonna be a high octane weekend with some high speed blasts down a back road doing test and tune

[GASoline71]

Actually it was yesterday. Installed new set of MSD Ignition 8.5mm Super Conductor plug wires. Way better than the cheapo Accel Super Stockers I had in there before.

Gary