1968 - Page 96 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Xeen · 04-22-2015, 07:41 AM

Wait I must be confused, the guy told you he will have your driveshaft done on the 3rd of May? WHAT? The local shop here in Topeka 4x4 Land has same day service with no wait AND they only charge $80 for a shorten and ballance, take it somewhere else.

gdavis · 04-23-2015, 03:34 PM

Quote:

Originally Posted by Xeen

Wait I must be confused, the guy told you he will have your driveshaft done on the 3rd of May? WHAT? The local shop here in Topeka 4x4 Land has same day service with no wait AND they only charge $80 for a shorten and ballance, take it somewhere else.

I had the wrong yoke also. I needed the short yoke and I had the long yoke. I couldn't find a short yoke. So he is going to shorten polish the yoke also. He is the only person in our county that does drive shafts and he is so busy. Unless, I wanted to drive to Ocala and that is over a hour each way. So I am going to go with him. I just didn't want to drive there and back two times. George

gdavis · 04-25-2015, 10:30 PM

I am out of town at this time. I went to see My sister a hour south of me. I have to wait until the 1st anyway. he told me that it would be ready the first not the third. Driveshaft.

Mustard72 · 04-27-2015, 09:42 PM

Good job getting it running, George!

gdavis · 04-28-2015, 05:47 PM

Quote:

Originally Posted by Mustard72

Good job getting it running, George!

Thanks guy. I am almost at the end of my build. I think I will be done with the heavy stuff this month. Then I will drive the old girl around a little. After I get the drive shaft installed I want to take her down to the front end shop.

gdavis · 05-02-2015, 10:45 PM

Today The driveshaft guy came and delivered the drive shaft. I installed the driveshaft and it fit like a glove. So I started the truck and put three quarts of transmission fluid in the transmission. I still need one more to top it off. I added brake fluid and I was going to bleed the brakes but my neighbor was busy so I put it off until Monday. After I bleed the system I will take it to the front end shop for some attention on the front end. Then it will be ready for a test drive.

Xeen · 05-02-2015, 10:51 PM

I take it the cam break in went well, and the engine checks out "OK" after the rebuild?

swamp rat · 05-04-2015, 12:07 AM

Hey George you can make a free Youtube account and put a folder load the engine running video into it and just post a link here, make sure the privacy setting is public.

gdavis · 05-05-2015, 11:19 PM

Quote:

Originally Posted by Xeen

I take it the cam break in went well, and the engine checks out "OK" after the rebuild?

yea the engine was great. I used my old torque converter and it made a little noise so I replaced it with a new one. As far as I know everything is aok. sounds great.

gdavis · 05-05-2015, 11:24 PM

Today I started to bleed the brakes and everything was going alone great until I got to the drivers side and the wheel cly. started to leak, So I will have to pull the wheel back off and see what the hey. Everything was new so go figure. If it is can break it will. This truck is one thing after another.

Xeen · 05-06-2015, 12:40 AM

George it's probably just something silly that will take you a few minutes to fix, but if not just replace it and forget about it.

gdavis · 05-06-2015, 03:05 PM

The plunger rod came out that's all. Got the brakes bleed and it pulled out of the shop area for the first time on it's own power. what a thrill. I got a appointment at the front end shop tomorrow at 9.00 for the front end alligment. After that it will be road ready. Here is a few pictures of the truck after a good bath.

72bowtiestepper · 05-06-2015, 03:26 PM

Lookin' Good George ! Have fun with it !

Xeen · 05-06-2015, 04:30 PM

The pickup looks great George, I especially like the blacked out grill trim and headlight rings paired with the blacked out rims it gives it a menacing look which stands in direct contrast to all the chrome and stainless that gives it that beautiful classic look, very nice.

kowboy63 · 05-06-2015, 10:09 PM

Looking good George.

Bomp · 05-06-2015, 11:00 PM

That is Sharp

swamp rat · 05-06-2015, 11:07 PM

Congratulations George!

colgad · 05-06-2015, 11:16 PM

Looking great George! Congrats!

**RenoKeene** · 05-07-2015, 04:00 PM

Truck looks great George! I'm just north of you a bit, maybe I'll cruise down in mine after the Love Bugs disappear.
Brad

gdavis · 05-07-2015, 06:03 PM

Quote:

Originally Posted by 72bowtiestepper

Lookin' Good George ! Have fun with it !

thanks a lot, I will try and have a ball with it. I got several issues to work out first. But thanks.

gdavis · 05-07-2015, 09:12 PM

Quote:

Originally Posted by Xeen

The pickup looks great George, I especially like the blacked out grill trim and headlight rings paired with the blacked out rims it gives it a menacing look which stands in direct contrast to all the chrome and stainless that gives it that beautiful classic look, very nice.

thanks Brian. I had it all orange and then I went with the black. It gave the truck a mean look.

gdavis · 05-07-2015, 09:13 PM

Quote:

Originally Posted by kowboy63

Looking good George.

thanks kowboy

gdavis · 05-07-2015, 09:14 PM

Quote:

Originally Posted by swamp rat

Congratulations George!

I got the front end adjusted today somewhat.

gdavis · 05-07-2015, 09:14 PM

Quote:

Originally Posted by Bomp

That is Sharp

coming from you that means a lot Bomp.

gdavis · 05-07-2015, 09:17 PM

Quote:

Originally Posted by colgad

Looking great George! Congrats!

I got the front end adjusted somewhat. he couldn't do the whole front end and he didn't charge me a dime. at least I am not plowing up dirt anymore.

04-22-2015, 07:41 AM	#2376
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: 1968 Wait I must be confused, the guy told you he will have your driveshaft done on the 3rd of May? WHAT? The local shop here in Topeka 4x4 Land has same day service with no wait AND they only charge $80 for a shorten and ballance, take it somewhere else. __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

04-25-2015, 10:30 PM	#2378
gdavis Registered User Join Date: Aug 2012 Location: Homosassa, Fl. Posts: 2,965	Re: 1968 I am out of town at this time. I went to see My sister a hour south of me. I have to wait until the 1st anyway. he told me that it would be ready the first not the third. Driveshaft. __________________ Check out Patches Cars I owned in the past. 1962 chev II Nova - 1965 Chevelle SS - (2)1966 Chevelle SS 1965 chev C10 57 belair chev 1967 Chevelle SS - 1969 Chevelle SS - 1972 Chevelle SS 1967 Buick electra 225 1995 Harley Davidson bager What does not kill you will make you stronger 1968 c10 short wheel base stepper

04-27-2015, 09:42 PM	#2379
Mustard72 Registered User Join Date: Jul 2012 Location: Ladysmith, WI Posts: 641	Re: 1968 Good job getting it running, George! __________________ Nick Old Mustard, 1972 Chevy C20, 350, TH350, 4.10 Dana 60 rear, owned since I was 16 in 1986 http://67-72chevytrucks.com/vboard/s...d.php?t=545356 Blue Bell, 1987 K20, 6.2L Diesel, TH400/NP208, 4.10 gears Ustahav 1976 K10, 350/350/203, Gov Loc, Yooper beater trail truck.

05-02-2015, 10:45 PM	#2381
gdavis Registered User Join Date: Aug 2012 Location: Homosassa, Fl. Posts: 2,965	Re: 1968 Today The driveshaft guy came and delivered the drive shaft. I installed the driveshaft and it fit like a glove. So I started the truck and put three quarts of transmission fluid in the transmission. I still need one more to top it off. I added brake fluid and I was going to bleed the brakes but my neighbor was busy so I put it off until Monday. After I bleed the system I will take it to the front end shop for some attention on the front end. Then it will be ready for a test drive. __________________ Check out Patches Cars I owned in the past. 1962 chev II Nova - 1965 Chevelle SS - (2)1966 Chevelle SS 1965 chev C10 57 belair chev 1967 Chevelle SS - 1969 Chevelle SS - 1972 Chevelle SS 1967 Buick electra 225 1995 Harley Davidson bager What does not kill you will make you stronger 1968 c10 short wheel base stepper Last edited by gdavis; 05-05-2015 at 11:30 PM.

05-02-2015, 10:51 PM	#2382
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: 1968 I take it the cam break in went well, and the engine checks out "OK" after the rebuild? __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

05-04-2015, 12:07 AM	#2383
swamp rat Registered User Join Date: Oct 2007 Location: Spanaway Posts: 8,451	Re: 1968 Hey George you can make a free Youtube account and put a folder load the engine running video into it and just post a link here, make sure the privacy setting is public. __________________ Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's

05-05-2015, 11:24 PM	#2385
gdavis Registered User Join Date: Aug 2012 Location: Homosassa, Fl. Posts: 2,965	Re: 1968 Today I started to bleed the brakes and everything was going alone great until I got to the drivers side and the wheel cly. started to leak, So I will have to pull the wheel back off and see what the hey. Everything was new so go figure. If it is can break it will. This truck is one thing after another. __________________ Check out Patches Cars I owned in the past. 1962 chev II Nova - 1965 Chevelle SS - (2)1966 Chevelle SS 1965 chev C10 57 belair chev 1967 Chevelle SS - 1969 Chevelle SS - 1972 Chevelle SS 1967 Buick electra 225 1995 Harley Davidson bager What does not kill you will make you stronger 1968 c10 short wheel base stepper

05-06-2015, 12:40 AM	#2386
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: 1968 George it's probably just something silly that will take you a few minutes to fix, but if not just replace it and forget about it. __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

05-06-2015, 03:05 PM	#2387
gdavis Registered User Join Date: Aug 2012 Location: Homosassa, Fl. Posts: 2,965	Re: 1968 The plunger rod came out that's all. Got the brakes bleed and it pulled out of the shop area for the first time on it's own power. what a thrill. I got a appointment at the front end shop tomorrow at 9.00 for the front end alligment. After that it will be road ready. Here is a few pictures of the truck after a good bath. Attached Images __________________ Check out Patches Cars I owned in the past. 1962 chev II Nova - 1965 Chevelle SS - (2)1966 Chevelle SS 1965 chev C10 57 belair chev 1967 Chevelle SS - 1969 Chevelle SS - 1972 Chevelle SS 1967 Buick electra 225 1995 Harley Davidson bager What does not kill you will make you stronger 1968 c10 short wheel base stepper

05-06-2015, 03:26 PM	#2388
72bowtiestepper Registered User Join Date: Feb 2013 Location: Northwest NJ Posts: 684	Re: 1968 Lookin' Good George ! Have fun with it !

05-06-2015, 04:30 PM	#2389
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: 1968 The pickup looks great George, I especially like the blacked out grill trim and headlight rings paired with the blacked out rims it gives it a menacing look which stands in direct contrast to all the chrome and stainless that gives it that beautiful classic look, very nice. __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build Last edited by Xeen; 05-06-2015 at 04:36 PM.

05-06-2015, 10:09 PM	#2390
kowboy63 Registered User Join Date: Feb 2013 Location: Georgia Posts: 193	Re: 1968 Looking good George.

05-06-2015, 11:00 PM	#2391
Bomp Registered User Join Date: Apr 2011 Location: . Posts: 3,104	Re: 1968 That is Sharp

05-06-2015, 11:07 PM	#2392
swamp rat Registered User Join Date: Oct 2007 Location: Spanaway Posts: 8,451	Re: 1968 Congratulations George! __________________ Mike. Swamp Rat build thread : http://67-72chevytrucks.com/vboard/s...d.php?t=595019 72 3/4T 4X4 4" BDS Lift 33" BFG's

05-06-2015, 11:16 PM	#2393
colgad Registered User Join Date: Jun 2006 Location: Lutz, Florida Posts: 838	Re: 1968 Looking great George! Congrats! __________________ 1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour



Register or Log In To remove these advertisements.

05-07-2015, 04:00 PM	#2394
RenoKeene Florida Edition Join Date: Oct 2010 Location: Fruitland Park, FL Posts: 4,028	Re: 1968 Truck looks great George! I'm just north of you a bit, maybe I'll cruise down in mine after the Love Bugs disappear. Brad __________________ 70 GMC Short Stepside "Rose"-An American Beauty: Factory 402/TH400, AM/FM, AC, Tilt, Tach, Buckets, Posi, PS, PB, 3-5 Drop, Complete Resto-Rod 67 C-20 Slant Back Wrecker "Mad Max" 67 C-10 Ratrod "Step-N-Wolf" 71 Serro Scotty Sportsman camper "Scotty" 97 LT1 Z28 "The Hornet" Link to more pics of "Rose" http://67-72chevytrucks.com/vboard/a...p?albumid=1684 Check out my "Cheap Tricks" thread and add to it if you can, lots of good info there. http://67-72chevytrucks.com/vboard/s...d.php?t=489394

Register or Log In To remove these advertisements.