|
05-06-2018, 12:42 AM | #1 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Saturday, Cinco de Mayo, 018
Journaling this just so I will remember what a total PAIN IN THE BUTT installing my bed has been. Short version, the bed wood has been on and off the truck twice so far and may come off again tomorrow. Today I thought I FINALLY had everything ready to install the bedsides - which are absolutely perfect to me. My son-in-law came over to help me lift each into place. I had the bolts in position, Never Seize on them, wrenches at hand etc. The front aligned perfect with the front bed panel. The bolt holes at the rear of the bedside did NOT match up! GRRR. Off by almost a full bolt diameter even though the bedside itself was up against the oak! Installation cancelled for today. I had somewhere I had to be at 4:00pm Tomorrow I will attempt to remove just the outer side boards to see if the bedsides will then mate up to the rear cross sill. If not the wood all has to come off again - #@*!&%. If it does and I tighten everything up minimizing the tolerances at each board & strip MAYBE the last side board will fit. If not I will consider my options carefully but wil probably have to rip a narrow strip off both side boards and refinish the boards edges. UGH UGH UGH!
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-06-2018, 04:28 PM | #2 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Sunday, May 6, 2018
Two outer boards removed easily. S-I-L and I got the bedsides on in a couple minutes, no scratches (YIPPEE!), bolts aligned easily. Never really like seeing the lock washer & nut at front bed side corners so I decided to try chrome acorn nuts. Bought the traditional pointy ones and I'm not sure how I feel about the look. They makes some flat ended ones...may have to swap them eventually. Opinions welcome. Now I have to cut the bed fill door into the wood & center strip correctly. this will be a case of measure THREE times, cut once with fingers and toes crossed.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-06-2018, 05:53 PM | #3 | |
Senior Member
Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
After the measure THREE times, drill a 1" hole and look to see if you are centered where you need to be, if you are off you can correct it. I decided to go with a fender door, instead of a bed fill, this is out of an 89 Ford Aerostar, has the same reverse curvature only needing an 1/8" rework. |
|
05-06-2018, 08:47 PM | #4 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Fender fill looks really good. I wanted to do that too but at the time I had sen way too much up to then and decided to let it go. I kinda regret it now but oh well. yours looks great.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-06-2018, 09:06 PM | #5 |
Senior Member
Join Date: Oct 2016
Location: Olympia, WA
Posts: 523
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Yours is coming along really nicely, a few bumps but it is really coming together! Hopefully mine will be on the road, unpainted, but on the road!
|
05-06-2018, 11:15 PM | #6 |
Senior Member
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Looks good Dan...Jim
__________________
my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> |
05-07-2018, 12:54 AM | #7 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Thanks Jim,
Trying to get it done enough to take it back to the body shop later this week for the hood to be fitted and repair on the interior window where I spewed it up! Tomorrow is really all the additional time I can spend on it before it has to go for awhile.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-07-2018, 02:51 AM | #8 |
Senior Member
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
|
Re: Danny Boy is BAACK! w/ '55 Big Window
gorgeous!
I dont mind the acorn nuts, looks like something you would really only focus on if you were staring at it.
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
05-07-2018, 09:11 AM | #9 |
Registered User
Join Date: Oct 2014
Location: Kitchener, Ontario, Canada
Posts: 3,254
|
Re: Danny Boy is BAACK! w/ '55 Big Window
nice touch.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=648459 https://67-72chevytrucks.com/vboard/...d.php?t=769441 1951 MG TD 1967 Jeep CJ5 1.9L TDI 33X13.5X15 Mud Grapplers. 1952 GMC 9700 p/u 7.3L diesel on air, dually |
05-07-2018, 10:15 AM | #10 |
Registered User
Join Date: Feb 2014
Location: Sunnyvale, CA
Posts: 605
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Dan truck is looking good. I think the Acorn nuts look good. I getting ready to start my bed wood and getting it in. I've
been told to put a plexiglass bed floor, I thought a tilting one I could open at a show.
__________________
1950 3100 5 window |
05-07-2018, 11:56 AM | #11 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Thanks so much, Mike.
If your rear suspension and frame are worthy of being under a plexi floor they must be REALLY great looking - huge congrats! I don’t know anything about how that would be done, hinged, lifted or secured but would you cut in slots for faux bed strips? Use a tinted plexi to coordinate with your paint? I can think of lots of ways to potentially customize it with details. It’s going to look SO great. Please post detailed pictures.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-15-2018, 12:29 PM | #12 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Just a status update:
Shortest possible version is that I continue to screw up! I have to lift the entire bed enough to tighten the fuel lines. I was so focused on getting the strips over the gas tank tightened and the electrical connections right that I put the fuel lines on then didn't go back to tighten them - DOH! I'm just a dumb**** anxious to get my truck drivable with no one to blame but myself, dammit!! Anyway, I am hatching a plan (hopefully this isn't yet another dumb move) that won't require me to find four friends to come over and fully remove it. I am thinking of temporarily replacing the through-frame bolts with large eyebolts, then use my engine lift to pick it up 1 ft. I can then tighten the fuel lines, double check the strip bolts, then lower it back on the frame with minimal disturbance.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-15-2018, 12:52 PM | #13 | |
Senior Member
Join Date: Sep 2016
Location: Hershey, PA
Posts: 1,004
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
__________________
Current Build Thread 1930 Ford Model A Modern Twist: Ford Model A Rat Rod With a Modern Twist Build Thread Phase 1 "The Swap": 1949 3100 with S10 swap. Beginner build with ambition! Build Thread Phase 2 "The Drop": Beginner Build with Ambition gets Air Ride |
|
05-17-2018, 03:55 PM | #14 | |
Senior Member
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
haha I just did the same thing, installed my bed before starting and the fuel pump had gone bad sitting. had to pull the bed and reinstall it SOLO, broke the gas cap doing it. screwing up is actually called "experience", better than being a hair dryer (all hot air) in my opinion.
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
|
05-17-2018, 06:49 PM | #15 | |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
I WAS feeling like a “hair dryer” before when Mike as doing all the mechanical work and Marcos all the body work. That was due to my mom being in hospice and not wanting to sell my truck as an unfinished project. It now i just feel so damn inept. Seems the more I try to plan things out and the more careful I am the dumber the mistakes I make. Wouldn’t be so bad if it wasn’t in finished paint already, but SHEESH!!
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
|
05-17-2018, 07:45 PM | #16 | |
Senior Member
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
__________________
the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393 |
|
05-18-2018, 12:34 AM | #17 | |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
We’ll see what the future brings but if someone ever offers me stupid money for it I MIGHT consider building a little more “useable” version.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
|
05-15-2018, 07:08 PM | #18 |
Registered User
Join Date: Jul 2011
Location: Las Vegas - Nev. aka Sin City
Posts: 1,835
|
Re: Danny Boy is BAACK! w/ '55 Big Window
hey dan
what about 4 good ratchet straps for lifting the bed and tie them all together at the top to lift the bed --- instead of the bolts --- use blankets to protect paint . just an idea |
05-15-2018, 07:32 PM | #19 | |
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,317
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
Works well. Be careful when coming down though ...... ha !
__________________
FAKKY 57 PANEL BUILD |
|
05-15-2018, 09:10 PM | #20 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
I have really considered using ratchet straps around the outside of the bed - I have two very large ones, not the little 3/4” wide ones sold at Haror Freight. But I’m scared of bending the bedsides inward AND I'm afraid of leaving abrasions on the paint. Blankets would work if I double/triple them up and use painter’s tape to keep them from slipping.
I have two of those ratcheting bars that go across the bed in my big truck to keep cargo from moving that I might be able to use to keep the bedsides from bending inward - again if I somehow protect the new paint in the bedsides from where they hit. Maybe a couple layers of cardboard. I’d not consider any of this but the chance the eyebolts might open up under the weight of the full bed occurs to me as a nightmare! I keep thinking, “How many other ways are there that I can screw this up?!”
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
05-15-2018, 09:25 PM | #21 |
A320 Pilot/USAF Retired
Join Date: Mar 2009
Location: Charleston, SC
Posts: 2,622
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Dan,
If the bed is not bolted down, you might try jacking up the truck and placing jack stands at the corners of the bed or under the cross sills, then lowering the truck, leaving the bed elevated.??? Make sure to protect the back of the cab!
__________________
JJ My 1957 build: http://67-72chevytrucks.com/vboard/s...d.php?t=334552 http://www.trifive.com/forums/showthread.php?t=22037 Instagram - Chuckdriver57 |
05-16-2018, 11:19 PM | #22 | |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Quote:
Of course it's already jacked up and on jack sands but I certainly could do what you suggest and it would work. I only need less than 1 foot of space. 6" would even be enough. Totally agree on protecting the back of the cab. Thanks for the suggestion, JJ! PS: What's the latest on your main truck?
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! |
|
05-31-2018, 11:29 AM | #23 |
Senior Member
Join Date: Aug 2010
Location: Shasta Lake, CA.
Posts: 1,619
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Oh the humanity ...
Nothing like DIY screw ups to make you humble . But then you can say I did it my way and learned what not to do. On the plus side you can proudly say I built that .
__________________
Glen & Jane's Rides ‘57 GMC NAPCO Long Bed V8 4 speed Bought 2008 7 other cars & trucks , 5 trailers '56 Chevy Long Bed I6, 4 speed Bought 1990 Sold 8.22.2020 ’56 GMC Suburban Pickup V8, 4 speed Hydramatic Bought 1996 Sold 10.11.2020 My Other Tinkerings http://67-72chevytrucks.com/vboard/s...75#post8967275 |
06-01-2018, 11:52 PM | #24 |
Senior Member
Join Date: Nov 2008
Location: Glendora, CA
Posts: 6,338
|
Re: Danny Boy is BAACK! w/ '55 Big Window
Friday, June 1, 2018
Ok, so I FINALLY finished assembling my bed today.... the 4th time. Sheesh, this was a p.i.t.a! I wish I could blame it on something other than my own stupidity but I can’t, damn! Anyway, she gets flat bedded to the paint shop tomorrow for final hood fitment, to repair chips on the window trim (ANOTHER stupid thing!) & install rear fenders. Glass shop is next door so the front & back windows will go in too. I bought polished stainless hood X bars and I’m debating billet SS hood hinges - expensive but cheaper than when I started on the truck. Anyway, that’s the current status. PS: These rims are 17x8’s and offset is wrong. I will replace them eventually but for now I’ve ordered spacers. i put washers on the studs to get it on the truck tomorrow. I used 7/16” washers so I assume that’s the stud size. Anyone know what replacement longer studs I should order? I know zip about Fords and this is a Ford 8.8 rearend. Any advice appreciated.
__________________
'55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda! Last edited by Dan in Pasadena; 06-01-2018 at 11:59 PM. |
06-02-2018, 12:44 AM | #25 |
Registered User
Join Date: Jun 2017
Location: upper midwest
Posts: 1,129
|
Re: Danny Boy is BAACK! w/ '55 Big Window
|
Bookmarks |
|
|