exhaust manifolds - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**JIMs70GMC** · 06-28-2002, 11:21 AM

I swapped out my stock center dump ramhorns for the vette ones. Anybody swapping out an I6 and needs some SBC exhaust manifolds, email me and make an offer. The studs look good, I did break one though. Could have pics in a couple days.

714x4lover · 07-07-2002, 12:20 PM

IM INTERESTED IN YOUR RAMHORNS. I WOULD BUY THEM IF THERE IN GOOD SHAPE AND THE PRICE IS RIGHT. I EMAILED YOU BUT DID NOT RECIEVE REPLY. I'M READY TO INSTALL NEW EXHAUST ALL I LACK IS THE RAMHORNS. THANKS 714X4LOVER

**JIMs70GMC** · 07-07-2002, 09:13 PM

Kinda busy the past few days. I sent you a PM.

06-28-2002, 11:21 AM	#1
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	exhaust manifolds I swapped out my stock center dump ramhorns for the vette ones. Anybody swapping out an I6 and needs some SBC exhaust manifolds, email me and make an offer. The studs look good, I did break one though. Could have pics in a couple days. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

07-07-2002, 12:20 PM	#2
714x4lover Registered User Join Date: Jun 2002 Location: Show Low, Arizona Posts: 211	ramhorns IM INTERESTED IN YOUR RAMHORNS. I WOULD BUY THEM IF THERE IN GOOD SHAPE AND THE PRICE IS RIGHT. I EMAILED YOU BUT DID NOT RECIEVE REPLY. I'M READY TO INSTALL NEW EXHAUST ALL I LACK IS THE RAMHORNS. THANKS 714X4LOVER

07-07-2002, 09:13 PM	#3
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Kinda busy the past few days. I sent you a PM. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.