Transfer case part question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

CheyLadd · 10-28-2007, 10:20 AM

The fitting for the speedometer cable on the piece that bolts to the rear of my 205 transfer case is a mess and is leaking a bunch of oil. First, what is this part called, and second, anyone know where I can get one? Is this a part I can get at napa? I am assuming I need to replace the whole piece and not just the speedometer input portion. If wrong, please let me know. I haven't torn it apart yet. Thanks. BTW, the truck is a 72 k10 swb.

**Yukon Jack** · 10-28-2007, 04:07 PM

I'm not seeing it on this link but go here and give these guys a call http://quad4x4.com/New%20Process%20N...fer%20Case.htm

CheyLadd · 10-28-2007, 04:18 PM

I should have pulled it apart before I asked. The prior owner had put a gob of sealant around the fitting. After getting all of that off, I took it apart and it was simply missing an o-ring. Problem fixed. Wish they were all that easy.

SoCal71K20 · 11-10-2007, 11:11 AM

Sorry for the late reply. Checkout www.norcalbigdawgs.net/Gallery/album49
Anyhow, if that site doesn't come up, you need GM # 326561 Sleeve. Rubber part of sleeve will wear out over time and cause fluid leak at this point. Real easy to change out. Good luck.

CheyLadd · 11-10-2007, 01:27 PM

Socal. Thanks. I finally get it. I have been trying to seal the speedo cable thinking it was missing something. I will get the part ordered.

10-28-2007, 10:20 AM	#1
CheyLadd Registered User Join Date: Oct 2006 Location: Glendora, CA Posts: 85	Transfer case part question The fitting for the speedometer cable on the piece that bolts to the rear of my 205 transfer case is a mess and is leaking a bunch of oil. First, what is this part called, and second, anyone know where I can get one? Is this a part I can get at napa? I am assuming I need to replace the whole piece and not just the speedometer input portion. If wrong, please let me know. I haven't torn it apart yet. Thanks. BTW, the truck is a 72 k10 swb.

10-28-2007, 04:07 PM	#2
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Re: Transfer case part question I'm not seeing it on this link but go here and give these guys a call http://quad4x4.com/New%20Process%20N...fer%20Case.htm __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

10-28-2007, 04:18 PM	#3
CheyLadd Registered User Join Date: Oct 2006 Location: Glendora, CA Posts: 85	Re: Transfer case part question I should have pulled it apart before I asked. The prior owner had put a gob of sealant around the fitting. After getting all of that off, I took it apart and it was simply missing an o-ring. Problem fixed. Wish they were all that easy.

11-10-2007, 11:11 AM	#4
SoCal71K20 Registered User Join Date: Jan 2002 Location: Lemon Grove, California Posts: 152	Re: Transfer case part question Sorry for the late reply. Checkout www.norcalbigdawgs.net/Gallery/album49 Anyhow, if that site doesn't come up, you need GM # 326561 Sleeve. Rubber part of sleeve will wear out over time and cause fluid leak at this point. Real easy to change out. Good luck.

11-10-2007, 01:27 PM	#5
CheyLadd Registered User Join Date: Oct 2006 Location: Glendora, CA Posts: 85	Re: Transfer case part question Socal. Thanks. I finally get it. I have been trying to seal the speedo cable thinking it was missing something. I will get the part ordered.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.