CA 292 Speed Parts - Clifford Dual Carb Manifold + Carbs - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**67_C20** · 02-14-2012, 05:57 PM

Fits 292 and 250 I6 engines. Used dual 4bbl Intake manifold, with water heat added (does not interfere with shorty headers). A dual 4bbl manifold with water heat is not a common part!

Also for sale, 4 slightly used carburators - 2 x 4bbl 390 CFM Holleys and 2 x 2bbl Holley Webers. Non-progressive linkages with both sets of carburators. Ended up deciding to simplify life and went with a single 4 bbl manifold. Ran great, looked great, but both dual setups drank fuel and are better suited for strip not street...had to learn that the hard (and expensive) way. Someone with more time could probably rejet or switch to progressive linkage.

Need to sell to fund another project. $500 takes all. I will sell either pair of carbs for $200 or the manifold separately for $200.

Fesser · 03-07-2012, 05:29 PM

What model are the Holley 4 barrels? Do they have chokes? Would you feel comfortable running them as is or do you think they need rebuilding?

**67_C20** · 03-07-2012, 09:38 PM

Fesser - sorry, my mistake. I took them out and they are Holley 6448 350 cfm 2 barrels. Link to Summit: http://www.summitracing.com/parts/HLY-0-7448/. They have maybe 50 miles on them, so I would say no, they shouldn't need rebuilding. Manual choke. Let me know...and thanks for your interest!

Fesser · 03-07-2012, 11:51 PM

Which setup worked better?

**67_C20** · 03-08-2012, 12:07 AM

Actually, the Holley Webers did. A little more of a challenge because they needed a bell crank to keep the mechanical liinkage, but it ran great from 2,500 rpm and up. Needed a little work on jetting down the idle circuit or maybe setting up a progressive linkage and I think it would have been there. But I ended up putting the truck in storage and then had someone else go through it a few years later and they didn't want to get into dual carbs, so I had it converted to a single 4bbl. The dual 350s ran REALLY rich at the low end, but I have a feeling either would have done the job eventually. Right now this is my daily driver and I'd rather concentrate on PS and PB. But neither set of carbs have been molested, I hope that's clear.

**Tmend** · 03-08-2012, 03:09 AM

Are you selling complete setup with all the linkage? If buy of you what else will I need to purchase ?
Posted via Mobile Device

**Tmend** · 03-08-2012, 03:16 AM

Pm sent
Posted via Mobile Device

**PICKMUP** · 03-08-2012, 03:49 PM

I'll take the set..all....thanks, frank

**PICKMUP** · 03-10-2012, 11:06 PM

Quote:

Originally Posted by PICKMUP

I'll take the set..all....thanks, frank

Any news on what happened here??? Status?

**PICKMUP** · 03-14-2012, 03:26 PM

Are these still available???

**LockDoc** · 03-14-2012, 09:57 PM

Quote:

Originally Posted by PICKMUP

Are these still available???

Frank,

He was on the board today at 7:05pm. Did you try sending him a PM?

LockDoc

02-14-2012, 05:57 PM	#1
67_C20 New Member Join Date: Nov 2011 Location: Forest Park, IL Posts: 10	292 Speed Parts - Clifford Dual Carb Manifold + Carbs Fits 292 and 250 I6 engines. Used dual 4bbl Intake manifold, with water heat added (does not interfere with shorty headers). A dual 4bbl manifold with water heat is not a common part! Also for sale, 4 slightly used carburators - 2 x 4bbl 390 CFM Holleys and 2 x 2bbl Holley Webers. Non-progressive linkages with both sets of carburators. Ended up deciding to simplify life and went with a single 4 bbl manifold. Ran great, looked great, but both dual setups drank fuel and are better suited for strip not street...had to learn that the hard (and expensive) way. Someone with more time could probably rejet or switch to progressive linkage. Need to sell to fund another project. $500 takes all. I will sell either pair of carbs for $200 or the manifold separately for $200. Attached Images

03-07-2012, 05:29 PM	#2
Fesser Registered User Join Date: Feb 2010 Location: Napa, CA Posts: 519	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs What model are the Holley 4 barrels? Do they have chokes? Would you feel comfortable running them as is or do you think they need rebuilding?

03-07-2012, 09:38 PM	#3
67_C20 New Member Join Date: Nov 2011 Location: Forest Park, IL Posts: 10	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs Fesser - sorry, my mistake. I took them out and they are Holley 6448 350 cfm 2 barrels. Link to Summit: http://www.summitracing.com/parts/HLY-0-7448/. They have maybe 50 miles on them, so I would say no, they shouldn't need rebuilding. Manual choke. Let me know...and thanks for your interest!

03-07-2012, 11:51 PM	#4
Fesser Registered User Join Date: Feb 2010 Location: Napa, CA Posts: 519	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs Which setup worked better?

03-08-2012, 12:07 AM	#5
67_C20 New Member Join Date: Nov 2011 Location: Forest Park, IL Posts: 10	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs Actually, the Holley Webers did. A little more of a challenge because they needed a bell crank to keep the mechanical liinkage, but it ran great from 2,500 rpm and up. Needed a little work on jetting down the idle circuit or maybe setting up a progressive linkage and I think it would have been there. But I ended up putting the truck in storage and then had someone else go through it a few years later and they didn't want to get into dual carbs, so I had it converted to a single 4bbl. The dual 350s ran REALLY rich at the low end, but I have a feeling either would have done the job eventually. Right now this is my daily driver and I'd rather concentrate on PS and PB. But neither set of carbs have been molested, I hope that's clear.

03-08-2012, 03:09 AM	#6
Tmend Senior Member Join Date: Nov 2010 Location: Reseda CA Posts: 1,294	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs Are you selling complete setup with all the linkage? If buy of you what else will I need to purchase ? Posted via Mobile Device __________________ Some progress is better then no progress

03-08-2012, 03:16 AM	#7
Tmend Senior Member Join Date: Nov 2010 Location: Reseda CA Posts: 1,294	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs Pm sent Posted via Mobile Device __________________ Some progress is better then no progress

03-08-2012, 03:49 PM	#8
PICKMUP "Trucks with Class" Join Date: Jul 2000 Location: OLYMPIA, WA, USA Posts: 8,139	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs I'll take the set..all....thanks, frank __________________ Email: frankeham@comcast.net Phone: 360-956-7170

03-14-2012, 03:26 PM	#10
PICKMUP "Trucks with Class" Join Date: Jul 2000 Location: OLYMPIA, WA, USA Posts: 8,139	Re: 292 Speed Parts - Clifford Dual Carb Manifold + Carbs Are these still available??? __________________ Email: frankeham@comcast.net Phone: 360-956-7170



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.