72 cheyenne dream - The 1947 - Present Chevrolet & GMC Truck Message Board Network

The Cheyenne Kid · 02-17-2006, 02:12 AM

Howdy all,

I’m the new kid in town (Pardon the pun. I can’t believe that name was available). I would like to ask ya’ll’s advice on my winter, now spring project.

Here’s what I got:

Mr. Green Jeans – 1971 Custom Deluxe C20 with newer 350 and new T350 (slated for my 80 CJ7) A/C cab (basically junk). Truck converted to a dually with the lowest geared rear end I’ve ever driven. 54 +/- MPH at 3000 RPM (500 something?), Trailing arm suspension and a flatbed. Gets 6-7 MPG. I drove this rolling pile of junk from Houston to Salt Lake City pulling a 4 horse trailer full of tools and with the bed stacked cab high with more junk and a John boat. I looked like Jed Clampet except none of the family would ride with me. If I can find a picture I’ll post it.

The Great Pumpkin – 1972 Custom K20, 350 and 465/NP205, Eaton rear, Dana 44(?) front, Spicer manual hubs. Non a/c cab (heavy rust in windshield frame, rockers and passenger floor pan). Gets 6.5-7 MPG. Bought in Seattle and drove to SLC with very little problem.

Blue Bell – 1972 Cheyenne Super Camper Special C20, 402 BB and 400T. 4:10 rear, factory heavy duty springs, a/c, tilt cruise, aux fuel tank …etc. (no vacuum gauge or tach. Why would someone order all this stuff and then skimp on a tach?) 99% complete. Rusty doors, cab corners, rockers (in & out), and all cab supports. Older repaint. Gets 10 MPG with stuck choke and need of tune up. Bought locally. Think tranny needs fluid change, filter, bands tightened.

The Dream:

Black Beauty - 1972 Cheyenne Super Camper Special 402 BB, 4X4, 4sp or 400T, dually w/ flatbed, 4” lift, aux. fuel tank, a/c, cruise, power locks/windows, tilt, Black on black, 10 + MPG.

Senerios:

1. Pull Cheyenne front clip and cab off and set on 4x4 frame (Labor intensive disconnecting wiring, a/c …etc. but, will allow for detailed painting)

Set 402 in 4X4 frame (New mounts? Body lift? Shift motor forward? Bigger radiator (use AT radiator?)?....etc?)

(Mount Clutch pedal in AT cab and cut hole in firewall for clutch rod, mount linkage assembly…etc?)

2. Pull 4X4 running gear off 4X4 frame

Remove front rear 2WD suspension

Mount 4X4 axels, springs, tranfercase

Cut holes in hump for shifter(s)

Misc?

A. Convert NP 205 and T400 to be compatible ( X-member(s), adaptors, machine work, yoke changes, output shaft change, possible tranny rebuild or sell existing and buy different)

B. Install manual tranny/tranfercase (Mount Clutch pedal in AT cab and cut hole in firewall for clutch rod, mount linkage assembly…etc?)

Misc?

I’m open for any and all suggestions, comments, direction and/or additional info. I’ve read through most of the archived comments on the web page but didn’t see this exact set up.

**N2TRUX** · 02-17-2006, 11:09 AM

Welcome to the forum Cheyenne Kid. I moved a copy of your post to the Welcome Forum. You might get a better response there.

jsbgump · 02-17-2006, 01:33 PM

Welcome to the board from Texas

97silv5.7 · 02-17-2006, 06:01 PM

Welcome to the board from Maine!

**Ron 586** · 02-18-2006, 02:09 AM

Welcome from West Tennessee. Thats quite a parts department you've got started. With that many choices you can't miss. BTW are you building a driver, show, or sell and buy something else truck out of this. Keep us posted on progress.

Bandit76 · 02-18-2006, 02:47 AM

Welcome from Kelowna, BC

OJOE · 02-18-2006, 09:11 AM

welcome from montgomery al

krue · 02-19-2006, 01:10 AM

Welcome to the board from South Mississippi!

LUV2XCLR8 · 02-19-2006, 08:11 AM

From West 10-UH-C

**special-K** · 02-19-2006, 08:42 PM

Welcome.Great Pumpkin is an old Asplundt truck,eh?

*SassyChevyGirl* · 02-20-2006, 12:16 AM

Hi! Welcome to the board!

The Cheyenne Kid · 02-27-2006, 02:37 AM

Cheyenne Dream update:

I've decided to go with senerio #1. I'm building a daily driver and this should be the last truck I buy/build. Yes, The Great Pumkin was an Asphlund truck. As you can tell, I'm pretty good at tearing thingss apart. I hope it goes back together as easy. Blue Bell's cab & clip are in the body shop. I'm now searching for a good chevy big block rebuilder in my neighborhood (Salt Lake City, UT). Any recommendations?

71SWBChevy · 02-27-2006, 04:35 PM

from KY!

**yote1234** · 04-04-2006, 12:47 AM

hello.....from az

**special-K** · 04-04-2006, 10:12 AM

Restore the Great Pumpkin back to it`s original Asplund spendor!!!Matbe they`d wanna buy it from you.

HotRod71 · 04-04-2006, 12:54 PM

Welcome aboard from TN

1969k10stepside · 04-06-2006, 12:23 PM

welcome

chevy_fatman · 04-09-2006, 09:31 PM

to the forum from PA!

gmcracing92 · 04-09-2006, 10:25 PM

from ND!!

*rage'nrat638* · 04-10-2006, 01:43 PM

welcome nice trucks...from il the rust belt...mark

The Cheyenne Kid · 10-08-2015, 09:28 PM

Hello All,

Long time since I was here. I'm now trying to list my Black Beauty on the classifieds but, cant find the link to do so. Any suggestions?

02-17-2006, 11:09 AM	#2
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: 72 cheyenne dream Welcome to the forum Cheyenne Kid. I moved a copy of your post to the Welcome Forum. You might get a better response there. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

02-17-2006, 01:33 PM	#3
jsbgump Gone Fishing Join Date: Aug 2005 Location: Fort Worth, Texas 76135 Posts: 12,361	Re: 72 cheyenne dream Welcome to the board from Texas __________________ 68 Chevy Short Fleetside LSX Swap Under Way 3.73 posi 2.5/4 drop Frame of resto has been started 2022 Hyundai Tucson Limited 2019 Chevy Traverse Redline Edition Wifes Ride Build Thread http://67-72chevytrucks.com/vboard/s...=1#post3483616

02-17-2006, 06:01 PM	#4
97silv5.7 MooMoo Join Date: Feb 2004 Location: Shapleigh, Maine Posts: 2,424	Re: 72 cheyenne dream Welcome to the board from Maine! __________________ '97 ext 4x4 3" body lift and 7'6" Fisher MM2 '04 Polaris 700 twin EFI sold 2-1-07 '07 Polaris 800 twin EFI Stealth Limited Edition Support the Board! Or deal with me foo! Its all fun and games till you find out shes 16.

02-18-2006, 02:09 AM	#5
Ron 586 RIP Mr Ron Join Date: Dec 2005 Location: Big Sandy, Tn. 38221 Posts: 8,166	Re: 72 cheyenne dream Welcome from West Tennessee. Thats quite a parts department you've got started. With that many choices you can't miss. BTW are you building a driver, show, or sell and buy something else truck out of this. Keep us posted on progress. __________________ Ron (Mr Round Tuit) Be kinder than necessary, for everyone you meet is fighting some kind of battle TN Message Forum TN Facebook Group SETN Truck Show My Photobucket Last edited by Ron 586; 02-18-2006 at 02:10 AM.

02-18-2006, 02:47 AM	#6
Bandit76 Registered User Join Date: Feb 2006 Location: BC Canada Posts: 3,606	Re: 72 cheyenne dream Welcome from Kelowna, BC __________________ 2011 Chev Silverado LT 1500 4x4 Crew Cab 5.3l 2005 Toyota 4Runner family beater ...would have more but my yard ain't all that big... ..nothing like a Chevy fence all bought and paid for.. ...there's a few holes in it though...

02-17-2006, 02:12 AM	#1
The Cheyenne Kid Registered User Join Date: Feb 2006 Location: Lufkin, TX Posts: 9	72 cheyenne dream Howdy all, I’m the new kid in town (Pardon the pun. I can’t believe that name was available). I would like to ask ya’ll’s advice on my winter, now spring project. Here’s what I got: Mr. Green Jeans – 1971 Custom Deluxe C20 with newer 350 and new T350 (slated for my 80 CJ7) A/C cab (basically junk). Truck converted to a dually with the lowest geared rear end I’ve ever driven. 54 +/- MPH at 3000 RPM (500 something?), Trailing arm suspension and a flatbed. Gets 6-7 MPG. I drove this rolling pile of junk from Houston to Salt Lake City pulling a 4 horse trailer full of tools and with the bed stacked cab high with more junk and a John boat. I looked like Jed Clampet except none of the family would ride with me. If I can find a picture I’ll post it. The Great Pumpkin – 1972 Custom K20, 350 and 465/NP205, Eaton rear, Dana 44(?) front, Spicer manual hubs. Non a/c cab (heavy rust in windshield frame, rockers and passenger floor pan). Gets 6.5-7 MPG. Bought in Seattle and drove to SLC with very little problem. Blue Bell – 1972 Cheyenne Super Camper Special C20, 402 BB and 400T. 4:10 rear, factory heavy duty springs, a/c, tilt cruise, aux fuel tank …etc. (no vacuum gauge or tach. Why would someone order all this stuff and then skimp on a tach?) 99% complete. Rusty doors, cab corners, rockers (in & out), and all cab supports. Older repaint. Gets 10 MPG with stuck choke and need of tune up. Bought locally. Think tranny needs fluid change, filter, bands tightened. The Dream: Black Beauty - 1972 Cheyenne Super Camper Special 402 BB, 4X4, 4sp or 400T, dually w/ flatbed, 4” lift, aux. fuel tank, a/c, cruise, power locks/windows, tilt, Black on black, 10 + MPG. Senerios: 1. Pull Cheyenne front clip and cab off and set on 4x4 frame (Labor intensive disconnecting wiring, a/c …etc. but, will allow for detailed painting) Set 402 in 4X4 frame (New mounts? Body lift? Shift motor forward? Bigger radiator (use AT radiator?)?....etc?) (Mount Clutch pedal in AT cab and cut hole in firewall for clutch rod, mount linkage assembly…etc?) 2. Pull 4X4 running gear off 4X4 frame Remove front rear 2WD suspension Mount 4X4 axels, springs, tranfercase Cut holes in hump for shifter(s) Misc? A. Convert NP 205 and T400 to be compatible ( X-member(s), adaptors, machine work, yoke changes, output shaft change, possible tranny rebuild or sell existing and buy different) B. Install manual tranny/tranfercase (Mount Clutch pedal in AT cab and cut hole in firewall for clutch rod, mount linkage assembly…etc?) Misc? I’m open for any and all suggestions, comments, direction and/or additional info. I’ve read through most of the archived comments on the web page but didn’t see this exact set up. Attached Images Last edited by The Cheyenne Kid; 02-17-2006 at 02:19 AM.

02-18-2006, 09:11 AM	#7
OJOE Crew Cut Join Date: Dec 2005 Location: MONTGOMERY,AL Posts: 757	Re: 72 cheyenne dream welcome from montgomery al __________________ 85 SWB 1/2 TON CREWCAB/5.3 03 CHEV 3500 DURAMAX CREW CAB 85 CHEV SWB/TPI 06 CHEV TAHOE (WIFES) 30 MODEL A HOT ROD 07 HARLEY DAVIDSON BAGGER 09 STREET GLIDE AN D A LOT MORE JUNK

02-19-2006, 01:10 AM	#8
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,450	Re: 72 cheyenne dream Welcome to the board from South Mississippi! __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

02-19-2006, 08:11 AM	#9
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,470	Re: 72 cheyenne dream From West 10-UH-C __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

02-19-2006, 08:42 PM	#10
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: 72 cheyenne dream Welcome.Great Pumpkin is an old Asplundt truck,eh? __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

02-20-2006, 12:16 AM	#11
SassyChevyGirl Account Suspended Join Date: Dec 2004 Location: somewhere over the rainbow Posts: 1,284	Re: 72 cheyenne dream Hi! Welcome to the board!

02-27-2006, 02:37 AM	#12
The Cheyenne Kid Registered User Join Date: Feb 2006 Location: Lufkin, TX Posts: 9	Re: 72 cheyenne dream Cheyenne Dream update: I've decided to go with senerio #1. I'm building a daily driver and this should be the last truck I buy/build. Yes, The Great Pumkin was an Asphlund truck. As you can tell, I'm pretty good at tearing thingss apart. I hope it goes back together as easy. Blue Bell's cab & clip are in the body shop. I'm now searching for a good chevy big block rebuilder in my neighborhood (Salt Lake City, UT). Any recommendations? Attached Images

02-27-2006, 04:35 PM	#13
71SWBChevy Post Whore Join Date: Aug 2005 Location: Owensboro KY Posts: 11,905	Re: 72 cheyenne dream from KY! __________________ Drew '71 Chevy 350/TH350 Hugger Orange Currently just a rolling frame, body work soon to follow!!! Check out my Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=212927 Daily Driver: 1997 Chevrolet S-10 with more gears than pistons

04-04-2006, 12:47 AM	#14
yote1234 Senior Member Join Date: Feb 2003 Location: Gold Canyon Arizona Posts: 4,276	Re: 72 cheyenne dream hello.....from az __________________ 1971 K5 CST Blazer 1965 Chevelle Malibu 283 (sadly sold) 1968 Camaro 327 1968 Honda mini-trail z50a #377 1966 uh 1-D Huey

04-04-2006, 10:12 AM	#15
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: 72 cheyenne dream Restore the Great Pumpkin back to it`s original Asplund spendor!!!Matbe they`d wanna buy it from you. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~



Register or Log In To remove these advertisements.

04-04-2006, 12:54 PM	#16
HotRod71 Short, Fleet, Slammed, V8 Club Join Date: Mar 2006 Location: Kingsport,TN Posts: 450	Re: 72 cheyenne dream Welcome aboard from TN __________________ Bill 71 Chevy SWB Fleetside (WIP) www.4x4grace.com

04-06-2006, 12:23 PM	#17
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,020	Re: 72 cheyenne dream welcome

04-09-2006, 09:31 PM	#18
chevy_fatman Where's my beer? Join Date: Aug 2002 Location: I live in the state of denial.... Posts: 5,621	Re: 72 cheyenne dream to the forum from PA! __________________ Paul How do you make the invisible, visible?.........You take it away.

04-09-2006, 10:25 PM	#19
gmcracing92 Drillin oil on American Soil! Join Date: Apr 2005 Location: Minot. North Dakota Posts: 418	Re: 72 cheyenne dream from ND!! __________________ Travis 70 Chevy c20 2wd 75 Chevy k10 4x4 parts truck 92 GMC Sierra c1500 2wd DD 99 Chevy Reg Cab Sht Box 1500 2wd 05 GMC Sierra Denali white

04-10-2006, 01:43 PM	#20
rage'nrat638 Account Suspended Join Date: Mar 2003 Location: THE FALL GUY CHICAGO IL Posts: 5,883	Re: 72 cheyenne dream welcome nice trucks...from il the rust belt...mark

10-08-2015, 09:28 PM	#21
The Cheyenne Kid Registered User Join Date: Feb 2006 Location: Lufkin, TX Posts: 9	Re: 72 cheyenne dream Hello All, Long time since I was here. I'm now trying to list my Black Beauty on the classifieds but, cant find the link to do so. Any suggestions?

Register or Log In To remove these advertisements.