![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Big Block Dipstick Problem
I needed a dipstick for my 68 with a Mark iV big block transplant. I bought one from a local parts store and the oil would not register on the stick. I pulled the tube and placed it on a similar oil pan laying around the shop. I filled it with 6 quarts of fluids to see where it would come to the dipstick, still no luck. My question is, how much fluid should be in the oil pan? Should the level surpass the sump? Do I need a better dipstick? Here's a picture of the mock up with 6 qts and it doesn't touch the tube or stick.
![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Dec 2012
Location: Upstate , New York
Posts: 647
|
Re: Big Block Dipstick Problem
5.5 quarts to fill my big block. My pickup is only 3/8 from the bottom of the pan
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2010
Location: Grand Terrace, Ca.
Posts: 1,607
|
Re: Big Block Dipstick Problem
I have a 502 in my truck. When I pull the dip stick and tube the stick sticks out from the bottom of the tube a few inches. Is this a universal dip stick and tube or an oil pan/motor specific dip stick and tube? If universal, you will need to determine how much oil your pan holds and adjust the dip stick tube length until you have the proper reading on the stick when the pan is full. Is there an O-ring and shoulder/seat on the tube for the O-ring to stop against?
|
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Re: Big Block Dipstick Problem
Quote:
|
|
![]() |
![]() |
![]() |
#5 | |
Registered User
Join Date: Nov 2010
Location: Grand Terrace, Ca.
Posts: 1,607
|
Re: Big Block Dipstick Problem
Quote:
What did the motor come out of? |
|
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Feb 2004
Location: Williamsburg, Ohio
Posts: 1,781
|
Re: Big Block Dipstick Problem
I have a chrome tube and stick from summit in my 402. I added 5 qts marked the stick then added the 6th and marked the stick.. I also used a conventional plug wire cap end --rubber-- slid over tube and over the pan insert and used a fuel line hose clamp to seal it better to the pan. I do like my 402 n my 67 4wd.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Nov 2006
Location: Sun City, Arizona
Posts: 430
|
Re: Big Block Dipstick Problem
Thank you, but for learning purposes, I am curious how close the oil level in a full pan is supposed to be to the baffle
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Dec 2013
Location: DALLAS, TX
Posts: 268
|
Re: Big Block Dipstick Problem
that all depends on the size of your pan. does the dipstick stick out of the end of the tube? the one I bought for mine sticks out about an inch. the one I originally picked up was for a small block and just the tip stuck out.
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Nov 2008
Location: Wappingers Falls, NY
Posts: 25
|
Re: Big Block Dipstick Problem
i once did the same thing, fooling around with oil capacities with the pan off, I was trying to optimize the oil level for a drag car with a bbc.
That was over 20 years ago, but iirc, 5 or 6 quarts does not reach the baffle, just as your pic shows. Looks like you need to get a real GM dipstick and tube.
__________________
F/S: 1972 C30 Stakebed parts truck F/S: 1967 C10 lwb stepside very rough 1978 C10 Longbed |
![]() |
![]() |
![]() |
#10 |
Proprietor of Dale's Corner
![]() Join Date: Nov 2012
Location: Vacaville , CA
Posts: 16,103
|
Re: Big Block Dipstick Problem
My 89 k30 usually with 454 and oil cooler calls for 8 tats in the owners manual
__________________
"Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man |
![]() |
![]() |
![]() |
Bookmarks |
|
|