![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Apr 2011
Location: Fairview Park, Ohio
Posts: 1,031
|
Rubber door bumper location and size?
Anyone got a pic of the rubber door bumpers on a truck.
I bought the kit but can seem to figure which hole is the location for the bumper. See pic. Need locations for these 3. Thanks! Mark Posted via Mobile Device |
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: Feb 2009
Location: Northern Nevada
Posts: 7,250
|
Re: Rubber door bumper location and size?
Not sure why three. Both my 71 & 72 use two per door. You should have two holes. One above the latch plate, one near the bottom of the door jam. The correct bumper is the one on top in your pic.
__________________
Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assembly kit for restoring the (a) truck from the ground up. My build thread, and more on the assembly kit https://67-72chevytrucks.com/vboard/...d.php?t=730025 |
![]() |
![]() |
![]() |
#3 |
Senior Member
![]() Join Date: Jun 2014
Location: Bushwood, MD
Posts: 510
|
Re: Rubber door bumper location and size?
Two of those are for the tailgate. The lower two in your pic. One of each for both sides
|
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Apr 2011
Location: Fairview Park, Ohio
Posts: 1,031
|
Quote:
Posted via Mobile Device |
|
![]() |
![]() |
![]() |
#5 |
Senior Member
![]() Join Date: Dec 1999
Location: TN/VA
Posts: 6,388
|
Re: Rubber door bumper location and size?
I am pretty sure they was three holes per side on the 67 and 68 if it still has the original rockers.
|
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,844
|
Re: Rubber door bumper location and size?
My '69 has always had 3 holes in each door jamb. However, from day one, only the top and bottom holes have had bumpers like the top one in the post 1 picture.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Oct 2017
Location: Glendale Colorado
Posts: 84
|
Re: Rubber door bumper location and size?
Really stupid question but how do you get those into the holes? mine seem too big to fit. I bought ones made for 67-72 chevy trucks.
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Apr 2011
Location: Fairview Park, Ohio
Posts: 1,031
|
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Oct 2017
Location: Glendale Colorado
Posts: 84
|
Re: Rubber door bumper location and size?
I tried this but it just seems like the pointed part is just too big. I press as hard as possible and it goes in a bit but can never get the whole pointed piece in. Just smashes down
|
![]() |
![]() |
![]() |
#10 | |
Registered User
Join Date: Apr 2011
Location: Fairview Park, Ohio
Posts: 1,031
|
Quote:
Posted via Mobile Device |
|
![]() |
![]() |
![]() |
#11 |
Senior Member
![]() Join Date: May 2010
Location: Wisconsin & Arizona
Posts: 4,844
|
Re: Rubber door bumper location and size?
I have had luck using silicone spray or silicone plumbers grease on the bumper and then pushing it in with a blunt Torx screwdriver or allen wrench of appropriate diameter inserted into the hole in the bumper.
Last edited by FirstOwner69; 12-05-2017 at 11:16 PM. |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Oct 2017
Location: Glendale Colorado
Posts: 84
|
Re: Rubber door bumper location and size?
I tried this as well. What size are the bumpers supppsed to be? Mine are 1/2 inch at the pointed part.
|
![]() |
![]() |
![]() |
#13 |
20' Daredevil (Ret)
![]() Join Date: May 2003
Location: Jefferson State
Posts: 13,647
|
Re: Rubber door bumper location and size?
Mine are also 1/2"..... and just below that tapered section, the part that will rest in the hole, is 5/16".
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Oct 2017
Location: Glendale Colorado
Posts: 84
|
Re: Rubber door bumper location and size?
|
![]() |
![]() |
![]() |
#15 |
20' Daredevil (Ret)
![]() Join Date: May 2003
Location: Jefferson State
Posts: 13,647
|
Re: Rubber door bumper location and size?
Not yet, the truck needs to be painted before I put the new bumpers in. Just lube 'em up and press one side in with a small screwdriver, then work your way around.
__________________
- Mike - 1972 K20 LWB 350/350/205 RIP El Jay |
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Oct 2017
Location: Glendale Colorado
Posts: 84
|
Re: Rubber door bumper location and size?
Just pushed one side in and pressed and they popped in. Still messing with the top spot on each side but the doors already close alot easier. Thanks for the help
|
![]() |
![]() |
![]() |
Bookmarks |
|
|