The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > All 4x4 Tech & Off Roading

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-07-2022, 10:40 AM   #1
scottmitchellrose
Registered User
 
Join Date: Feb 2015
Location: durham nc
Posts: 124
70 k10 front problems

2 years into trouble. replaced wheel bearings twice but she keeps eating them- causing the steering to pull to the right magically- dangerous. I have an 85 from axle i picked up for 300 (disc brakes). rather than swapping the whole axle, can I just replace it from the 'knuckles' on out? or is it best to just swap the whole thing- ball joints, etc. will not line up? Any videos or tips on such a swap? I think I need a different booster, master cylinder and portioning valve. Any recommendations for that setup too? Thanks a lot.
scottmitchellrose is offline   Reply With Quote
Old 02-07-2022, 10:41 AM   #2
scottmitchellrose
Registered User
 
Join Date: Feb 2015
Location: durham nc
Posts: 124
Re: 70 k10 front problems

Quote:
Originally Posted by scottmitchellrose View Post
2 years into trouble. replaced wheel bearings twice but she keeps eating them- causing the steering to pull to the right magically- dangerous. I have an 85 from axle i picked up for 300 (disc brakes). rather than swapping the whole axle, can I just replace it from the 'knuckles' on out? or is it best to just swap the whole thing- ball joints, etc. will not line up? Any videos or tips on such a swap? I think I need a different booster, master cylinder and portioning valve. Any recommendations for that setup too? Thanks a lot.
oh- and will the hub knobs/ spring/ locks work on the 85 or are they different from the 70?
scottmitchellrose is offline   Reply With Quote
Old 02-15-2022, 05:45 PM   #3
duallyjams
Registered User
 
duallyjams's Avatar
 
Join Date: May 2007
Location: Deale Md
Posts: 4,663
Re: 70 k10 front problems

Had the same problem. I tried replacing with a used one off of a spare rear that I have but had the same problem, the bearing did not have a tight / snug fit, luckily the aftermarket world has plenty, replaced with a new one, problem solved.



Name:  IMG_3259.jpg
Views: 441
Size:  43.3 KB
__________________
James

63 GMC V6 4speed carryall
65 chevy swb bbw V8 auto
68 K20 327/4 speed, buddy buckets
2002 GMC CC Dually Duramax

64 GMC lwb 3/4 V6 4speed SOLD
66 GMC swb bbw buddy buckets SOLD

IG duallyjams

The only thing that stays the same is constant change!
duallyjams is offline   Reply With Quote
Old 02-16-2022, 10:03 AM   #4
scottmitchellrose
Registered User
 
Join Date: Feb 2015
Location: durham nc
Posts: 124
Re: 70 k10 front problems

[QUOTE=duallyjams;9035302]Had the same problem. I tried replacing with a used one off of a spare rear that I have but had the same problem, the bearing did not have a tight / snug fit, luckily the aftermarket world has plenty, replaced with a new one, problem solved.



thanks a lot- that spindle in the photo- it will fit a 1970 (drum) k10? where did you get it?! Scott
scottmitchellrose is offline   Reply With Quote
Old 02-16-2022, 10:09 AM   #5
duallyjams
Registered User
 
duallyjams's Avatar
 
Join Date: May 2007
Location: Deale Md
Posts: 4,663
Re: 70 k10 front problems

[quote=scottmitchellrose;9035534]
Quote:
Originally Posted by duallyjams View Post
Had the same problem. I tried replacing with a used one off of a spare rear that I have but had the same problem, the bearing did not have a tight / snug fit, luckily the aftermarket world has plenty, replaced with a new one, problem solved.



thanks a lot- that spindle in the photo- it will fit a 1970 (drum) k10? where did you get it?! Scott
It's for a big bearing disc brakes. I bought it off of Ebay.
__________________
James

63 GMC V6 4speed carryall
65 chevy swb bbw V8 auto
68 K20 327/4 speed, buddy buckets
2002 GMC CC Dually Duramax

64 GMC lwb 3/4 V6 4speed SOLD
66 GMC swb bbw buddy buckets SOLD

IG duallyjams

The only thing that stays the same is constant change!
duallyjams is offline   Reply With Quote
Old 02-16-2022, 05:16 PM   #6
61K10
Registered User
 
61K10's Avatar
 
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
Re: 70 k10 front problems

Scott---go to the 60-66 forum and the build section--search for 61k10 build. all the info toward the end (disc on the closed knuckle). New spindles from Yukon-hubs from Rockauto. they are big bearing spindles and hubs.
All the outer stuff of the 85 will be the big bearing stuff. It's all in my build--good luck

Kimble
__________________
1961 chevy K10

my build is------------61K10 build
61K10 is offline   Reply With Quote
Old 03-03-2022, 04:29 AM   #7
Richard
Senior Member
 
Join Date: Dec 1999
Location: Southern California
Posts: 2,856
Re: 70 k10 front problems

RuffStuff has small and big bearing spindles for the Dana 44.
Big bearing https://www.ruffstuffspecialties.com/R2590.html
Small bearing https://www.ruffstuffspecialties.com/r2573.html
__________________
Richard
1972 K10 Custom Deluxe SWB Fleetside
My build https://67-72chevytrucks.com/vboard/...d.php?t=800746
Richard is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:40 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com