Window Crank and Door Handle Removal - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Dick Dale · 09-08-2004, 10:08 PM

I cannot get those things off. I know there is a pin or spring that holds them on but no luck. Any tips, advise, prayers are all welcome. Idiot proof pictures would be great.

Joe67 · 09-08-2004, 10:14 PM

You need to visit the local auto parts store and pick up a window crank removal tool for a few bucks

There is a C clip behind each handle, use the tool like this:

71swb4x4 · 09-08-2004, 10:15 PM

I alwys use a screw driver to gently pry the handle out a bit and a needle nose plier or tweezer to grab the clip. It would be much easier to by the right tool though.

jimfulco · 09-08-2004, 11:06 PM

I use a piece of coathanger wire with a 1"x3" loop on one end for maneuverability, & a tiny hook (bent, then cut) on the other end that grabs the clip in the center. Watch those clips, they tend to fly out of sight real fast.

67cst · 09-08-2004, 11:23 PM

even with that tool it can be a pain in the arse, especially if those clips get bent, ive found that the original clips work a lot better then the ones on the help rack at the parts store too, so like jimfulco says, dont let them go flyin!

68w/sbc406 · 09-08-2004, 11:51 PM

i have used the red shop rags before. terry cloth works too but kinda thick.

mrein3 · 09-09-2004, 07:46 AM

I bought one of the tools 67c10step has pictured above after about 10 years of trying to use the methods others talked about.

BUY THE TOOL

Not having that tool is like trying to remove a phillips head screw with a coat hanger.

Blue Beard · 09-09-2004, 07:58 AM

I've got one of those tools, been using it for years.

Some other methods will cause damage.

Old Dave · 09-09-2004, 08:28 AM

Go buy the tool. Best $4 I ever spent...

A few 72's · 09-09-2004, 10:07 AM

I have one of the removal tools, but have also used the free paint can openers from the hardware stores. Slide the curved tip under the handle and it will fit around the center of the clip. Just pull the clip out.

Iminocca · 09-09-2004, 04:13 PM

The clip removal tool is well woth the money! Since no one else mentioned it, you don't need the tool for reinstalling the clip, just push the clip all the way back in place and slip the handle back on to the shaft. The end of the shaft is tapered and the clip slips over it and locks into place. Took me a couple of years to figure that one out!
Patrick

Dick Dale · 09-09-2004, 05:32 PM

I got them off. Driver side window was stubborn, and thank god I am replacing the panels.

09-08-2004, 10:08 PM	#1
Dick Dale Excelsior, You Fathead. Join Date: Jun 2004 Location: Valparaiso, In Posts: 937	Window Crank and Door Handle Removal I cannot get those things off. I know there is a pin or spring that holds them on but no luck. Any tips, advise, prayers are all welcome. Idiot proof pictures would be great. __________________ Go Navy. The Sea Is Ours. Budget 350 Build http://67-72chevytrucks.com/vboard/s...38#post2264638

09-08-2004, 10:14 PM	#2
Joe67 67 is sold Join Date: Apr 2001 Location: Troy, Michigan Posts: 6,738	You need to visit the local auto parts store and pick up a window crank removal tool for a few bucks There is a C clip behind each handle, use the tool like this: __________________ Joe - Formerly 67c10step ------------------------------- 1967 Chevy Stepside - ECE 4/6, fuelcell, 5lug - SOLD gr8lakes - My ebay auctions Click here to order forum apparel :: Click here to become a subscribing member

09-08-2004, 10:15 PM	#3
71swb4x4 Senior Member Join Date: Nov 2003 Location: Brookings, SD Posts: 10,497	I alwys use a screw driver to gently pry the handle out a bit and a needle nose plier or tweezer to grab the clip. It would be much easier to by the right tool though. __________________ Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs.

09-08-2004, 11:23 PM	#5
67cst i love summertime Join Date: Jul 2002 Location: Kelowna BC Posts: 4,303	even with that tool it can be a pain in the arse, especially if those clips get bent, ive found that the original clips work a lot better then the ones on the help rack at the parts store too, so like jimfulco says, dont let them go flyin! __________________ 1967 shortbox stepside Chevy, 365 hp 327, th400. GLOVE BOX LIGHTS FORSALE, click link for info http://67-72chevytrucks.com/vboard/s...d.php?t=273724

09-08-2004, 11:51 PM	#6
68w/sbc406 Got Light Emitting Diode? Join Date: Apr 2004 Location: Newberg, OR Posts: 2,485	i have used the red shop rags before. terry cloth works too but kinda thick. __________________ 1968 1/2 ton 2wd lwb 6 lug disc and bags up front. Next c notch and rear bags '02 Chevy Silverado LT ext cab short bed 2WD 5/7 drop on 22's(the family car) 1993 Cherokee work ride/weekend wheeler

09-08-2004, 11:06 PM	#4
jimfulco Registered User Join Date: May 2003 Location: Shreveport LA Posts: 3,170	I use a piece of coathanger wire with a 1"x3" loop on one end for maneuverability, & a tiny hook (bent, then cut) on the other end that grabs the clip in the center. Watch those clips, they tend to fly out of sight real fast.

09-09-2004, 07:46 AM	#7
mrein3 Registered User Join Date: Feb 2000 Location: Center City, MN, USA Posts: 3,253	I bought one of the tools 67c10step has pictured above after about 10 years of trying to use the methods others talked about. BUY THE TOOL Not having that tool is like trying to remove a phillips head screw with a coat hanger. __________________ '70 cab, '71 chassis, 383, TH350, NP205. '71 Malibu convertible '72 Malibu hard top Center City, MN

09-09-2004, 07:58 AM	#8
Blue Beard Registered User Join Date: Jan 2003 Location: Washington State Posts: 8,834	I've got one of those tools, been using it for years. Some other methods will cause damage. __________________ 1970 Chev CST 2003 Harley Fatboy 1975 Chevrolet Step Van 1956 Chev Bel Air 1977 Blazer 2WD For Sale $3000.00 1978 Blazer 2WD For Sale $7000.00 1978 Silverado 2005 Monte Carlo

09-09-2004, 08:28 AM	#9
Old Dave Is a bullfrog waterproof? Join Date: Nov 2000 Location: OLATHE, KANSAS Posts: 1,130	Go buy the tool. Best $4 I ever spent... __________________ "It is better to remain silent and be thought a fool, than to open one's mouth and remove all doubt." Ben Franklin __________________ 1970 Chevy shortbed 2002 Harley Custom Chopper (Long sucker) 1998 K2500 5.7L 5-speed Longbed 1st two are My son's toys...they just live in my garage! 1997 GMC K1500 Suburban 1993 S-10 Blazer 4D (youngest son's daily driver) 2000 Dodge Ram 4WD Ext. Cab (5.9L) Wife is a late year 1951

09-09-2004, 10:07 AM	#10
A few 72's Registered User Join Date: Mar 2004 Location: Alabama Posts: 705	I have one of the removal tools, but have also used the free paint can openers from the hardware stores. Slide the curved tip under the handle and it will fit around the center of the clip. Just pull the clip out. __________________ 1972 C10 SWB 350 / T400 1972 SWB GMC 350/T350 1972 Cheyenne 20 super "long horn". 402BB / T400 1972 Suburban C10 Deluxe 350 / T350 and a few more.. http://www.myspace.com/afew72s

09-09-2004, 04:13 PM	#11
Iminocca Registered User Join Date: Aug 2004 Location: Orange County Posts: 10	The clip removal tool is well woth the money! Since no one else mentioned it, you don't need the tool for reinstalling the clip, just push the clip all the way back in place and slip the handle back on to the shaft. The end of the shaft is tapered and the clip slips over it and locks into place. Took me a couple of years to figure that one out! Patrick __________________ '71 C20 Camper Special

09-09-2004, 05:32 PM	#12
Dick Dale Excelsior, You Fathead. Join Date: Jun 2004 Location: Valparaiso, In Posts: 937	I got them off. Driver side window was stubborn, and thank god I am replacing the panels. __________________ Go Navy. The Sea Is Ours. Budget 350 Build http://67-72chevytrucks.com/vboard/s...38#post2264638



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.