The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board > Squarebody Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-16-2015, 04:43 AM   #1
jtodus
Registered User
 
Join Date: Sep 2015
Location: Sumter SC
Posts: 5
Ol' Jesse

What's up fellas. Been a long time reader but first post here. I've always wanted a square body and I recently came across one and scooped it up. Ol' Jesse my wife calls it because it reminds her of uncle Jesse from Dukes of Hazard. lol. Anyway, It seemed to have the basic things I was looking for. It's a 1987 GMC Sierra 4x4. One of the previous owners did an auto to manual transmission swap and put in an NV4500. The truck needs a lot of work and I'm willing to put the $$ in. Now, I'm no mechanic but I'm also not mechanically declined. I also have plenty of friends that are very mechanically inclined and between us we have everything we need to do the work that I plan on getting done. I picked this truck up right before I left on my deployment so I didn't get much time with it. I'm looking for guidance on what to buy and how I should do this rebuild. I've got a budget of around $15k. Things I know I need to do: Rebuild the motor and tranny. New front and rear axles. New gears. New clutch and all clutch parts. Needs to be re-wired. Lots of Cosmetic stuff. Pretty much a total rebuild. Not even sure if the 4WD works. it has no Front drive shaft in it. Any guidance would be greatly appreciated. I have about 6 1/2 Months before i'll be able to complete any of the work but would like to start ordering parts and getting them sent to my buddies garage. Ready to sponge....fill me with your knowledge!!!


This is the only pic I got on my phone before I left. I can get the wife to take some more if I need them.
Attached Images
 
jtodus is offline   Reply With Quote
Old 11-16-2015, 05:15 AM   #2
MTCK
Registered User
 
MTCK's Avatar
 
Join Date: Dec 2009
Location: Fairbanks, AK
Posts: 1,830
Re: Ol' Jesse

Cool truck and welcome. I hope you have a good and safe deployment. It's good you have a budget figured. Often times folks (myself included!) drastically underestimate the cost of these projects.

I don't know what your goals are for the truck, but 15k could go a real long ways or not very far at all. I'd make a list of what you want to do. Anything you can get at a salvage yard, and any work you can do yourself will help stretch that coin. That's a unique ride already with the 5 speed. Are you going to keep it fuel injected?
__________________
-Marcus

1991 V3500 L29 454 4L80E NP205 D60/14 Bolt 4.56's
1984 K30 292 TH400 NP205 D60/14 Bolt 4.56's flat bed 7'6" Meyer Plow
2022 Silverado 3500 L8T
Project Daily Driver
Project Heavy Hauler
Project Plow Truck
MTCK is offline   Reply With Quote
Old 11-16-2015, 04:03 PM   #3
Chevy_mud_truck
Registered User
 
Chevy_mud_truck's Avatar
 
Join Date: Feb 2015
Location: Lester West Virginia
Posts: 244
Re: Ol' Jesse

Little more information might help out. what's your plan when finished daily driver/weekend toy/any off-road use. If your doing upgrade try to plan it out to keep from buying stuff twice ask lots of questions if you're not sure on something working together there's a lot of good guy's on here that will know someone or have bolted up peace together off the wall combination of parts to build some sick rigs
Chevy_mud_truck is offline   Reply With Quote
Old 11-16-2015, 05:47 PM   #4
jtodus
Registered User
 
Join Date: Sep 2015
Location: Sumter SC
Posts: 5
I want to go big with it. It'll be a toy but not strictly off road use. I want to be able to turn 44s no problem if I decide to go that route. When my wife yelled at me for buying a "piece of ****" truck I told her it will be the most badass looking truck in town...by 2017 haha. As far as keeping it fuel injected...I don't see why not but I'm not partial either way.
Posted via Mobile Device
jtodus is offline   Reply With Quote
Old 11-17-2015, 01:48 AM   #5
Chevy_mud_truck
Registered User
 
Chevy_mud_truck's Avatar
 
Join Date: Feb 2015
Location: Lester West Virginia
Posts: 244
Re: Ol' Jesse

To run 44" tires I would recommend 1 ton axles with some with some 5:13 or so gears probably 14 to16 inchs of lift crossover steering and being such a short wheelbase some good driveshafts what will work with the angle that there going to be running at is going to be pretty step and I would run a 205 transfer case if it don't have one swapped in yet then of course the tires and wheels of your choice there's a lot of choices to choose from
My build is a 78 long bed 12" suspension 3" body 1tons Dana 60 front 14full floter 5:13 gears 454 turbo 400 203/205 doubler crossover steering with hydo assistance
Chevy_mud_truck is offline   Reply With Quote
Old 11-19-2015, 03:17 AM   #6
jtodus
Registered User
 
Join Date: Sep 2015
Location: Sumter SC
Posts: 5
Re: Ol' Jesse

Awesome thanks for the info. Keep the knowledge flowing fellas. My shopping list is growing. The worst part about this is not being able to show you guys in progress/final product pics for like 7 months.
jtodus is offline   Reply With Quote
Old 11-28-2015, 10:50 AM   #7
silverbear
Registered User
 
silverbear's Avatar
 
Join Date: Feb 2014
Location: Glen St. Mary, Florida
Posts: 304
Re: Ol' Jesse

If you are shopping for a wire harness, forum member GMACHINZ sells high quality stock replacement harnesses or upgraded units for reasonable prices. I have used some of his upgrades and am very pleased with them.
__________________
86 Chevrolet K10 350/SM465 Frankie SOLD
1995 GMC Yukon GT SOLD
1996 GMC Yukon GT
2010 Suburban 1500 4x4 5.3l/6L80e. Sold
2016 Silverado 2500HD Crew Cab 4x4 6.0l/6L80e
silverbear is offline   Reply With Quote
Old 11-30-2015, 06:46 AM   #8
jtodus
Registered User
 
Join Date: Sep 2015
Location: Sumter SC
Posts: 5
Thanks fella. It's definitely on the list.
Posted via Mobile Device
jtodus is offline   Reply With Quote
Old 12-01-2015, 12:52 AM   #9
Chevy_mud_truck
Registered User
 
Chevy_mud_truck's Avatar
 
Join Date: Feb 2015
Location: Lester West Virginia
Posts: 244
Re: Ol' Jesse

Just about forgot to mention steering box support/brace and reinforce plate
Chevy_mud_truck is offline   Reply With Quote
Old 12-01-2015, 01:34 AM   #10
jtodus
Registered User
 
Join Date: Sep 2015
Location: Sumter SC
Posts: 5
Re: Ol' Jesse

What about the clutch? Since it was an automatic and a previous owner did the manual conversion, do I need find a clutch/components from a manual square body?
Posted via Mobile Device
jtodus is offline   Reply With Quote
Reply

Bookmarks

Tags
1987, 4x4, gmc, sierra, square body


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:51 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com