SBC Intake Bolt ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

quickchevy · 05-09-2009, 04:37 PM

Going to replace my intake.I read where arp bolts are shorter than they use to make.That you should use BBC intake bolts because they are longer.SBC is 1.00 and BBC are 1.25.Its a performer eps.What do yall think.

cdowns · 05-09-2009, 05:42 PM

i never pay attention to prepacked bolt kits i always measure what i need and use the correct length bolts

fdbdw · 05-23-2009, 10:32 AM

hey quick, getting ready to install a new intake and was wondering what you ended up doing for bolts, hope it whent well

quickchevy · 05-23-2009, 10:57 AM

Been busy and have not got around to it.I have arp bolt kit for small block chevy.

70c10 · 05-23-2009, 08:50 PM

I called ARP last year and was told the SBC bolts are what you need for the aftermarket intakes but I remember a board member had problems and switched to the longer BBC bolts with no problems.

quickchevy · 05-23-2009, 10:12 PM

Thanks.Thought i saw it on here at some point.

Marv D · 05-24-2009, 11:20 AM

Especially with aftermarket intakes and heads, you need to pay attention to the bolts that line up with a couple of the pushrods. If you use too LONG of a bolt you will make contact and bend or rub the pushrod. Especially in aftermarket heads where they have shifted the valve / rocker/pushrod placement to make bigger intake ports this can be a serious ugly. The two end bolts are blind holes (meaning they are not a 'through hole' with threads all the way through a hole) The threads will not go 100% to the bottom of the hole in that boss cast at the end of the heads. Just make sure your bolt is the right length to have plenty of thread contact, but not bottom in the hole. Your particular intake gasket material, and intake flange thickness will be different than the stock setup so like cdowns said you really need to just measure what you need for each bolt to get it 100% right.

quickchevy · 05-24-2009, 05:19 PM

Ok thanks.Its a ELD eps intake and camel back heads fel pro 1256

fdbdw · 06-09-2009, 07:45 AM

hey quikchevy
just installed my eld eps and 1406 and wanted to catch up with ya and let you now that i used 1" bolts and they were plenty long enough I have stock heads so probably some difference there, just letting ya know

05-09-2009, 04:37 PM	#1
quickchevy Registered User Join Date: Apr 2008 Location: Augusta,Ga Posts: 119	SBC Intake Bolt ? Going to replace my intake.I read where arp bolts are shorter than they use to make.That you should use BBC intake bolts because they are longer.SBC is 1.00 and BBC are 1.25.Its a performer eps.What do yall think.

05-09-2009, 05:42 PM	#2
cdowns Senior Member Join Date: Jan 2003 Location: daytonabeach Posts: 22,956	Re: SBC Intake Bolt ? i never pay attention to prepacked bolt kits i always measure what i need and use the correct length bolts __________________ 71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY

05-23-2009, 10:32 AM	#3
fdbdw Registered User Join Date: Jan 2009 Location: colorado springs Posts: 479	Re: SBC Intake Bolt ? hey quick, getting ready to install a new intake and was wondering what you ended up doing for bolts, hope it whent well

05-23-2009, 10:57 AM	#4
quickchevy Registered User Join Date: Apr 2008 Location: Augusta,Ga Posts: 119	Re: SBC Intake Bolt ? Been busy and have not got around to it.I have arp bolt kit for small block chevy.

05-23-2009, 08:50 PM	#5
70c10 67-72 Addict! Join Date: Feb 2002 Location: The TAX State! Posts: 7,857	Re: SBC Intake Bolt ? I called ARP last year and was told the SBC bolts are what you need for the aftermarket intakes but I remember a board member had problems and switched to the longer BBC bolts with no problems. __________________ Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads

05-23-2009, 10:12 PM	#6
quickchevy Registered User Join Date: Apr 2008 Location: Augusta,Ga Posts: 119	Re: SBC Intake Bolt ? Thanks.Thought i saw it on here at some point.

05-24-2009, 11:20 AM	#7
Marv D Registered Truck Offender Join Date: May 2008 Location: hells training ground (aka Ariz) Posts: 3,118	Re: SBC Intake Bolt ? Especially with aftermarket intakes and heads, you need to pay attention to the bolts that line up with a couple of the pushrods. If you use too LONG of a bolt you will make contact and bend or rub the pushrod. Especially in aftermarket heads where they have shifted the valve / rocker/pushrod placement to make bigger intake ports this can be a serious ugly. The two end bolts are blind holes (meaning they are not a 'through hole' with threads all the way through a hole) The threads will not go 100% to the bottom of the hole in that boss cast at the end of the heads. Just make sure your bolt is the right length to have plenty of thread contact, but not bottom in the hole. Your particular intake gasket material, and intake flange thickness will be different than the stock setup so like cdowns said you really need to just measure what you need for each bolt to get it 100% right. __________________ Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral.

05-24-2009, 05:19 PM	#8
quickchevy Registered User Join Date: Apr 2008 Location: Augusta,Ga Posts: 119	Re: SBC Intake Bolt ? Ok thanks.Its a ELD eps intake and camel back heads fel pro 1256

06-09-2009, 07:45 AM	#9
fdbdw Registered User Join Date: Jan 2009 Location: colorado springs Posts: 479	Re: SBC Intake Bolt ? hey quikchevy just installed my eld eps and 1406 and wanted to catch up with ya and let you now that i used 1" bolts and they were plenty long enough I have stock heads so probably some difference there, just letting ya know



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.