Question about body mount assembly - The 1947 - Present Chevrolet & GMC Truck Message Board Network

leftybass209 · 08-09-2013, 07:33 PM

I have a counterparts aftermarket body mount set for 69-72. My question is, do I reuse the square washer located under the front body mount? This is not the core support mount, but the actual front body mount under the floorboard. Thanks in advance.

67ctener · 08-09-2013, 08:33 PM

I also have the same kit and have no idea where anything goes
Posted via Mobile Device

leftybass209 · 08-09-2013, 09:27 PM

I have a good idea where the parts go, just not sure about that square washer. I will take a picture of this tomorrow, as my dad and I will be doing the cab swap then. Might be some trial and error, but hell or high water its getting done with pics tomorrow!
Posted via Mobile Device

JointTech · 08-09-2013, 09:34 PM

I got a kit from class heartbeat and I had to reuse my square washers in the front. I sandblasted and painted them. mine were rusty and this is a CA truck so im sure there are some completely gone ones back east. They dont look to be anything special. just a big washer.
I wonder if those are actually just factory spacers which is why they arent in ANY of the kits.

**LockDoc** · 08-09-2013, 10:01 PM

-
This thread might help a little.

http://67-72chevytrucks.com/vboard/s...d.php?t=192342

Just remember that the 1/2 ton and 3/4 ton body mounts are different. Also the '67 & '68 core support mounts are different than the '69 up..

LockDoc

leftybass209 · 08-09-2013, 10:10 PM

It is a 1/2 ton c10. Thanks for the replies!
Posted via Mobile Device

In The Ten Ring · 08-09-2013, 11:09 PM

Very timely my friends! I will soon be tackling this job as well. I got the kit from Classic Heartbeat....hope it works!

I plan to use my dremel tool to remove the tac weld on the forward cab bolts and I do plan to replace all bolts.

I'm getting a new radiator when I do this as well.

08-09-2013, 07:33 PM	#1
leftybass209 Registered User Join Date: Feb 2011 Location: Modesto, CA Posts: 2,186	Question about body mount assembly I have a counterparts aftermarket body mount set for 69-72. My question is, do I reuse the square washer located under the front body mount? This is not the core support mount, but the actual front body mount under the floorboard. Thanks in advance.

08-09-2013, 08:33 PM	#2
67ctener Registered User Join Date: Oct 2012 Location: Arlington Washington Posts: 1,808	Re: Question about body mount assembly I also have the same kit and have no idea where anything goes Posted via Mobile Device __________________ Scott 67 c10 sold 89 c1500 90 k2500 91 s10 #chevyonly

08-09-2013, 09:27 PM	#3
leftybass209 Registered User Join Date: Feb 2011 Location: Modesto, CA Posts: 2,186	Re: Question about body mount assembly I have a good idea where the parts go, just not sure about that square washer. I will take a picture of this tomorrow, as my dad and I will be doing the cab swap then. Might be some trial and error, but hell or high water its getting done with pics tomorrow! Posted via Mobile Device

08-09-2013, 09:34 PM	#4
JointTech Registered User Join Date: Feb 2012 Location: Mission Viejo, CA Posts: 1,856	Re: Question about body mount assembly I got a kit from class heartbeat and I had to reuse my square washers in the front. I sandblasted and painted them. mine were rusty and this is a CA truck so im sure there are some completely gone ones back east. They dont look to be anything special. just a big washer. I wonder if those are actually just factory spacers which is why they arent in ANY of the kits. __________________ 72 C20 Long Bed SB350 TH400 14 bolt rear end Extremely boring build thread

08-09-2013, 10:01 PM	#5
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,406	Re: Question about body mount assembly - This thread might help a little. http://67-72chevytrucks.com/vboard/s...d.php?t=192342 Just remember that the 1/2 ton and 3/4 ton body mounts are different. Also the '67 & '68 core support mounts are different than the '69 up.. LockDoc __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

08-09-2013, 10:10 PM	#6
leftybass209 Registered User Join Date: Feb 2011 Location: Modesto, CA Posts: 2,186	Re: Question about body mount assembly It is a 1/2 ton c10. Thanks for the replies! Posted via Mobile Device

08-09-2013, 11:09 PM	#7
In The Ten Ring Registered User Join Date: Jun 2013 Location: West Virginia Posts: 6,421	Re: Question about body mount assembly Very timely my friends! I will soon be tackling this job as well. I got the kit from Classic Heartbeat....hope it works! I plan to use my dremel tool to remove the tac weld on the forward cab bolts and I do plan to replace all bolts. I'm getting a new radiator when I do this as well.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.