TX WTB 60-66 suburban or panel filler neck - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ljackson · 01-19-2014, 01:57 PM

60-66 suburban or panel filler neck, door and sheet metal. I want to install a door and fill assembly in my 64 fleet. I have the fuel tank already under the bed.

LT1 Burb · 01-19-2014, 02:19 PM

I have a door off of a 59 nomad, it might work if you can't find anything else.

ljackson · 01-19-2014, 02:26 PM

Thanks. I'll keep it in mind. Is it just the door? Do you have a pic? After a quick web search, it looks to have a lot of curve. Quite a bit more than fleetside bed?

**Captainfab** · 01-20-2014, 01:20 AM

I have some Suburban/Panel fuel fill doors with the surrounding sheetmetal. I'll have to check and see if I have any fill tubes left.

ljackson · 01-20-2014, 07:39 AM

Thanks, Capt

ljackson · 01-24-2014, 08:22 PM

Quote:

Originally Posted by Captainfab

I have some Suburban/Panel fuel fill doors with the surrounding sheetmetal. I'll have to check and see if I have any fill tubes left.

Any luck Capt.?

**Captainfab** · 01-25-2014, 12:29 PM

Sorry but I haven't had much time with working 12hrs a day 7 days a week. I did not find a filler tube at my shop, but I should have one at home in the garage. I just need to find the time to look for it. I'll try and get to it this weekend.

Quote:

Originally Posted by ljackson

Any luck Capt.?

ljackson · 02-09-2014, 11:36 AM

Thanks Capt for fixin me up, it looks good to me. It appears to be easily repairable. Just to be sure I understand how these fit, the "box" will go between the inner and outer bed sides (skins) and the filler will connect to my tank on the plane between the top of the frame and the bottom of the bed wood? When it is set up like described, the curves will match?

Capt. Said "It looks like the shipping will be $21.00 which makes the total $86.00". actual shipping was $32.75

Capt, I want it. PM sent

**Captainfab** · 02-09-2014, 02:07 PM

I haven't installed one of these in a pickup box yet, but yes the filler tube should pass between the top of the frame and the bed floor. If you are using the Blazer tank, you may have to modify the filler tube , the tank neck or both. It shouldn't be difficult to do.

The inner box of the filler door assembly will interfere with the inner bed panel. You will need to either trim the fill door box, or make a small bulge in your inner bed panel. The Suburbans and Panels have a bulge in the inner wall to accomodate the filler box.

I replied to your PM.

Quote:

Originally Posted by ljackson

Thanks Capt for fixin me up, it looks good to me. It appears to be easily repairable. Just to be sure I understand how these fit, the "box" will go between the inner and outer bed sides (skins) and the filler will connect to my tank on the plane between the top of the frame and the bottom of the bed wood? When it is set up like described, the curves will match?

Capt. Said "It looks like the shipping will be $21.00 which makes the total $86.00".

Capt, I want it. PM sent

ljackson · 02-09-2014, 04:43 PM

Quote:

Originally Posted by Captainfab

I haven't installed one of these in a pickup box yet, but yes the filler tube should pass between the top of the frame and the bed floor. If you are using the Blazer tank, you may have to modify the filler tube , the tank neck or both. It shouldn't be difficult to do.

The inner box of the filler door assembly will interfere with the inner bed panel. You will need to either trim the fill door box, or make a small bulge in your inner bed panel. The Suburban’s and Panels have a bulge in the inner wall to accommodate the filler box.

I replied to your PM.

Thanks for the info, I built my tank to between the frame rails.
If anyone that is following this wants to see what I built: http://67-72chevytrucks.com/vboard/s...d.php?t=428182 Post # 4.

Thanks, I have not been able to actually look a sub or panel. I’ve been trying to see from forum photos.

I believe this is going to work well.

PM sent regarding Payment

ljackson · 02-22-2014, 07:03 PM

The filler arrived in great shape. Thanks to Captainfab. Balance for shipping sent to capt's PP acct.

LT1 Burb · 02-09-2014, 12:15 PM

I did look at the wagon one and it is way to curved for a pickup.

ljackson · 02-09-2014, 12:31 PM

Quote:

Originally Posted by LT1 Burb

I did look at the wagon one and it is way to curved for a pickup.

Thanks for the input.

ABNGRNT13 · 02-23-2014, 12:13 PM

By chance, do you have another one of these door setups?

01-19-2014, 01:57 PM	#1
ljackson Registered User Join Date: Apr 2009 Location: Amarillo, Texas Posts: 636	WTB 60-66 suburban or panel filler neck 60-66 suburban or panel filler neck, door and sheet metal. I want to install a door and fill assembly in my 64 fleet. I have the fuel tank already under the bed. __________________ Father and son built. Driven daily since 2012. 283, 3 speed. Mostly original. '81 PS and disk front. Fuel tank relocate. Maintenance, repairs and upgrades on his dime now. http://zacks64longfleet.shutterfly.com/ Higher res. photos in my gallery.

01-19-2014, 02:19 PM	#2
LT1 Burb Registered User Join Date: Sep 2010 Location: Winchester Oregon, formerly Vancouver BC Posts: 2,949	Re: WTB 60-66 suburban or panel filler neck I have a door off of a 59 nomad, it might work if you can't find anything else.

01-19-2014, 02:26 PM	#3
ljackson Registered User Join Date: Apr 2009 Location: Amarillo, Texas Posts: 636	Re: WTB 60-66 suburban or panel filler neck Thanks. I'll keep it in mind. Is it just the door? Do you have a pic? After a quick web search, it looks to have a lot of curve. Quite a bit more than fleetside bed? __________________ Father and son built. Driven daily since 2012. 283, 3 speed. Mostly original. '81 PS and disk front. Fuel tank relocate. Maintenance, repairs and upgrades on his dime now. http://zacks64longfleet.shutterfly.com/ Higher res. photos in my gallery. Last edited by ljackson; 01-19-2014 at 02:33 PM.

01-20-2014, 01:20 AM	#4
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,250	Re: WTB 60-66 suburban or panel filler neck I have some Suburban/Panel fuel fill doors with the surrounding sheetmetal. I'll have to check and see if I have any fill tubes left. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

01-20-2014, 07:39 AM	#5
ljackson Registered User Join Date: Apr 2009 Location: Amarillo, Texas Posts: 636	Re: WTB 60-66 suburban or panel filler neck Thanks, Capt __________________ Father and son built. Driven daily since 2012. 283, 3 speed. Mostly original. '81 PS and disk front. Fuel tank relocate. Maintenance, repairs and upgrades on his dime now. http://zacks64longfleet.shutterfly.com/ Higher res. photos in my gallery.

02-09-2014, 11:36 AM	#8
ljackson Registered User Join Date: Apr 2009 Location: Amarillo, Texas Posts: 636	Re: WTB 60-66 suburban or panel filler neck Thanks Capt for fixin me up, it looks good to me. It appears to be easily repairable. Just to be sure I understand how these fit, the "box" will go between the inner and outer bed sides (skins) and the filler will connect to my tank on the plane between the top of the frame and the bottom of the bed wood? When it is set up like described, the curves will match? Capt. Said "It looks like the shipping will be $21.00 which makes the total $86.00". actual shipping was $32.75 Capt, I want it. PM sent __________________ Father and son built. Driven daily since 2012. 283, 3 speed. Mostly original. '81 PS and disk front. Fuel tank relocate. Maintenance, repairs and upgrades on his dime now. http://zacks64longfleet.shutterfly.com/ Higher res. photos in my gallery. Last edited by ljackson; 02-22-2014 at 06:50 PM.

02-22-2014, 07:03 PM	#11
ljackson Registered User Join Date: Apr 2009 Location: Amarillo, Texas Posts: 636	Re: WTB 60-66 suburban or panel filler neck The filler arrived in great shape. Thanks to Captainfab. Balance for shipping sent to capt's PP acct. __________________ Father and son built. Driven daily since 2012. 283, 3 speed. Mostly original. '81 PS and disk front. Fuel tank relocate. Maintenance, repairs and upgrades on his dime now. http://zacks64longfleet.shutterfly.com/ Higher res. photos in my gallery.

02-09-2014, 12:15 PM	#12
LT1 Burb Registered User Join Date: Sep 2010 Location: Winchester Oregon, formerly Vancouver BC Posts: 2,949	Re: WTB 60-66 suburban or panel filler neck I did look at the wagon one and it is way to curved for a pickup.

02-23-2014, 12:13 PM	#14
ABNGRNT13 Registered User Join Date: Dec 2013 Location: Fort Mitchell, AL (out the back gate of Ft Benning) Posts: 140	Re: WTB 60-66 suburban or panel filler neck By chance, do you have another one of these door setups? __________________ SSG Walker Harris '72 Cheyenne Longbed '66 Panel '66 Short Stepside '65 Short Fleetside



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.