hood shaking - The 1947 - Present Chevrolet & GMC Truck Message Board Network

krazy_texan · 01-12-2003, 12:02 AM

i have a problem when i wrecked my truck i grabbed a hood to put on the truck out of a salvage yard, well now i have the hood on and when i drive the truck the center of the hood shakes like it is just a real thin piece of sheet metal laying over the engine and shakes really bad

Mudder · 01-12-2003, 12:06 AM

on the inside of the hood theres two supports that run from front to back. do they have some 4inch wide fillers between them and the sheet metal?

PanelDeland · 01-12-2003, 12:08 AM

There are some rattle strips that fit between the X brace and the hood.They may need replacing(probably do after30+ years.These hoods are not known for their great strength in this area.I have heard of people putting cowl hoods on to get more hood stability,

Longhorn Man · 01-12-2003, 02:01 AM

Heh...I've never seen one NOT do that!

JoetheMobster · 01-12-2003, 02:51 AM

Here I thought I was the only one that had the hood shake!! Personally I don't mind it! Friendly reminder that I'm not in my dinky 4cyl car!!

MStokes · 01-12-2003, 01:06 PM

I've had my C20 for a long time and never had a problem with it shaking. When I got my C10 I noticed it did shake quite a bit. I was figuring on having to replace the strips between the sheet metal and the braces on the underside of the hood and hope that cleared it up.

Has anybody gone as far as putting in another cross brace to add more support right in the middle of the hood?

Mudder · 01-12-2003, 01:08 PM

Putting the strips in should take care of it if they fit tight.

casey · 01-18-2003, 07:59 PM

Does the 67-68 hood shake like that, they look stronger than the 69-72 hoods, this might be a dum question can a 67-68 hood fit on a 71 or is different on the front?

chevy2racr · 01-19-2003, 01:32 AM

well, if you modify the piss outta it. it'd take fabbingwork, I may try this some day, that or just get a whole 67-68 clip. found this pic a while back

Brewski* · 01-19-2003, 11:11 AM

My hood looked like it was going to fly off the truck it shook so bad. I not only put the new padding between the cross members and the sheetmetal but put new foam on the back and front stabilizers also. New hood bumper stops and new hood levelers and it is so rock solid it never moves at all. I think it was about 20.00 for all but worht every penny~~!

PanelDeland · 01-19-2003, 11:21 AM

67-68n hoods don't work with the later front clips.The way most people get the laid back look in front of the hood is to pie slice the hood and lay it back.I haven't done one (no body man here) but it does look cool and only someone who really knows these trucks would notice.

01-12-2003, 12:02 AM	#1
krazy_texan Registered User Join Date: Oct 2002 Location: West Des Moines, Ia Posts: 3,233	hood shaking i have a problem when i wrecked my truck i grabbed a hood to put on the truck out of a salvage yard, well now i have the hood on and when i drive the truck the center of the hood shakes like it is just a real thin piece of sheet metal laying over the engine and shakes really bad __________________ Krazy Texan My Trucks are made with Wrenches not Chop Sticks 1967 GMC 3/4 ton "Johnny Cash" 1990 v1500 suburban 1967 Ford f100 Swb 4x4 "green bean" GOD BLESS JESUS, JOHN WAYNE, AND THE ALAMO

01-12-2003, 12:08 AM	#3
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,993	There are some rattle strips that fit between the X brace and the hood.They may need replacing(probably do after30+ years.These hoods are not known for their great strength in this area.I have heard of people putting cowl hoods on to get more hood stability, __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"

01-12-2003, 02:51 AM	#5
JoetheMobster Listening since '86 Join Date: Sep 2001 Location: Canada Posts: 1,799	Here I thought I was the only one that had the hood shake!! Personally I don't mind it! Friendly reminder that I'm not in my dinky 4cyl car!! __________________ 2007 Saturn Aura - hey it WAS a GM product

01-12-2003, 01:06 PM	#6
MStokes Registered User Join Date: Aug 2002 Location: Meridian, Idaho Posts: 164	I've had my C20 for a long time and never had a problem with it shaking. When I got my C10 I noticed it did shake quite a bit. I was figuring on having to replace the strips between the sheet metal and the braces on the underside of the hood and hope that cleared it up. Has anybody gone as far as putting in another cross brace to add more support right in the middle of the hood? __________________ 1972 C-10 LWB, 400/350, 2WD 1972 C-20 Custom Camper, 350/350, 4WD (Converted)

01-19-2003, 01:32 AM	#9
chevy2racr So Many Ideas, So Little Money Join Date: Sep 2001 Location: Marshalltown, IA Posts: 1,610	well, if you modify the piss outta it. it'd take fabbingwork, I may try this some day, that or just get a whole 67-68 clip. found this pic a while back Attached Images __________________ 72 Blazer 3/4 ton running gear 4.10s NP205/TH350 350 4in lift half doors 71 C10 with 454 99 S-10 5.1L SBC 700R4 09 Malibu Marshalltown, Iowa

01-12-2003, 12:06 AM	#2
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	on the inside of the hood theres two supports that run from front to back. do they have some 4inch wide fillers between them and the sheet metal?

01-12-2003, 02:01 AM	#4
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Heh...I've never seen one NOT do that!

01-12-2003, 01:08 PM	#7
Mudder Registered User Join Date: Feb 2001 Location: East Central, MO Posts: 11,336	Putting the strips in should take care of it if they fit tight.

01-18-2003, 07:59 PM	#8
casey Registered User Join Date: Jan 2003 Location: Kelowna B.C. Canada Posts: 2,048	Does the 67-68 hood shake like that, they look stronger than the 69-72 hoods, this might be a dum question can a 67-68 hood fit on a 71 or is different on the front?

01-19-2003, 11:11 AM	#10
Brewski* Registered User Join Date: Aug 2001 Location: Rocky Mount, MO Posts: 1,293	My hood looked like it was going to fly off the truck it shook so bad. I not only put the new padding between the cross members and the sheetmetal but put new foam on the back and front stabilizers also. New hood bumper stops and new hood levelers and it is so rock solid it never moves at all. I think it was about 20.00 for all but worht every penny~~!

01-19-2003, 11:21 AM	#11
PanelDeland I am a Referee of life. Join Date: Jun 2000 Location: Greensboro N.C. Posts: 13,993	67-68n hoods don't work with the later front clips.The way most people get the laid back look in front of the hood is to pie slice the hood and lay it back.I haven't done one (no body man here) but it does look cool and only someone who really knows these trucks would notice. __________________ The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.