The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-17-2012, 05:09 PM   #1
Bradydz
Registered User
 
Bradydz's Avatar
 
Join Date: Sep 2011
Location: Medford, Oregon
Posts: 119
Any idea what this wire is for?

(if you saw this post previously, I reposted because it was moved to truck audio, which doesn't really even make sense..)

I bought the LMC keyless entry kit, and when I opened it, I understand what to do with everything, except this yellow wire. It connects to the controller away from the rest of the wiring harness, and it is not mentioned ANYWHERE in the instructions. Anyone have an idea what it's for? It splits into two wires, and is only about 4 feet long.
Attached Images
    
Bradydz is offline   Reply With Quote
Old 01-17-2012, 06:40 PM   #2
Larry64
Registered User
 
Join Date: Sep 2011
Location: Lewisburg, TN
Posts: 315
Re: Any idea what this wire is for?

I would call LMC & ask them.
Larry
Larry64 is offline   Reply With Quote
Old 01-17-2012, 08:45 PM   #3
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: Any idea what this wire is for?

looks like shrink wrapped diodes in there. There are cars, like older BMW that take a positive pulse to lock and a negative pulse to unlock, so when I was installing a keyless on them I wold use just the positive lock output (that should be where that two pin plugs into, where the lock and unlock outputs are on the brain) and put diodes in just like that. Looks like a pre made harness for doing it. There are also cars with factory alarm systems that need the same setup.

The LMC keyless is probably just a generic keyless that they include with their relays and actuators to make it specific to your truck. I have a whole toolbox of stuff that "came in the box" and didnt fit the application, I say give it a chuck over the nearest shoulder.
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 01-17-2012, 08:48 PM   #4
Bradydz
Registered User
 
Bradydz's Avatar
 
Join Date: Sep 2011
Location: Medford, Oregon
Posts: 119
Re: Any idea what this wire is for?

Quote:
Originally Posted by joedoh View Post
looks like shrink wrapped diodes in there. There are cars, like older BMW that take a positive pulse to lock and a negative pulse to unlock, so when I was installing a keyless on them I wold use just the positive lock output (that should be where that two pin plugs into, where the lock and unlock outputs are on the brain) and put diodes in just like that. Looks like a pre made harness for doing it. There are also cars with factory alarm systems that need the same setup.

The LMC keyless is probably just a generic keyless that they include with their relays and actuators to make it specific to your truck. I have a whole toolbox of stuff that "came in the box" and didnt fit the application, I say give it a chuck over the nearest shoulder.
So you're saying it should be fine without hooking it up to anything? I just wanted to make sure, so I don't have it all installed, and not having it work.
Bradydz is offline   Reply With Quote
Old 01-17-2012, 10:20 PM   #5
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: Any idea what this wire is for?

Id bet there is a second harness that plugs in there, with a blue and a green wire. It may be a separate harness with two bosch relays. give me a picture of the wiring diagram and I can help you.
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 01-18-2012, 03:35 AM   #6
Bradydz
Registered User
 
Bradydz's Avatar
 
Join Date: Sep 2011
Location: Medford, Oregon
Posts: 119
Re: Any idea what this wire is for?

Quote:
Originally Posted by joedoh View Post
Id bet there is a second harness that plugs in there, with a blue and a green wire. It may be a separate harness with two bosch relays. give me a picture of the wiring diagram and I can help you.
The diagram is TINY, and my phone won't get a big enough picture, to where it would be legible..
I just don't really understand what that could be used for, seeing as it splices into one wire. The left and right actuator, along with all the wires, are all on the main harness, with no yellow wires anywhere.
Bradydz is offline   Reply With Quote
Old 01-18-2012, 03:50 AM   #7
Bradydz
Registered User
 
Bradydz's Avatar
 
Join Date: Sep 2011
Location: Medford, Oregon
Posts: 119
Re: Any idea what this wire is for?

Quote:
Originally Posted by joedoh View Post
Id bet there is a second harness that plugs in there, with a blue and a green wire. It may be a separate harness with two bosch relays. give me a picture of the wiring diagram and I can help you.
Wait, I just found something I must've skipped over before on the main harness. There are two wires that do not go to anything I have, and one wire is white, the other is brown. I just looked at the tiny wiring diagram, and the two I found go off to the left, and connect to a, "spare negative trigger", and where the wires are, the white says "unlock", the other says, "lock". Is this yellow wire with relays considered a negative trigger, you think?
Bradydz is offline   Reply With Quote
Old 01-18-2012, 10:56 AM   #8
joedoh
Senior Member
 
joedoh's Avatar
 
Join Date: May 2007
Location: Doodah Kansas
Posts: 7,774
Re: Any idea what this wire is for?

no I would guess those as auxiliary outputs for trunk pop or triggering a remote start.

I think you are putting to much emphasis on this. If you cant get a picture of the wiring diagram I am just guessing, but it is really common to have universal parts in the box that arent used. Like I said, I have a toolbox full. Its also pretty common not to use every single wire on the plug, when I did keyless there were always wires I chopped off short, like positive door inputs for some ford models, or trunk pop wiring when the car didnt have a trunk, or dome light triggers when the customer didnt select that option.

the yellow with diodes is 90% likely to be not used. if you get a picture of the pinout or wiring diagram, I can tell you for sure. cheers!
__________________
the mass of men live lives of quiet desperation


if there is a problem, I can have it.

new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393
joedoh is offline   Reply With Quote
Old 01-18-2012, 12:51 PM   #9
MTBADBOB
Registered User
 
Join Date: Oct 2011
Location: Boulder, MT
Posts: 24
Re: Any idea what this wire is for?

Could it be the signal wire for the remote??? I've seen these type of units have a long, seperate wire to extend for the pick-up of the remote signal from long distances. I'm with joedoh, leave it off & see if everything works ok.

Last edited by MTBADBOB; 01-18-2012 at 12:55 PM. Reason: lack of info
MTBADBOB is offline   Reply With Quote
Reply

Bookmarks

Tags
keyless, lmc, wire


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:00 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com