|
|
|
10-11-2005, 02:40 AM
|
#1 |
|
Registered User
Join Date: Dec 2003
Location: Glendale Arizona
Posts: 747
|
Converting to 4x4
Ok I have a 70 half ton long bed that I am thinking of converting to 4x4.
So can I just get a solid axle from any 67-87 chevy 4x4? Can I also just get a rear axle off any 67-87 4x4 and just bolt in the leaf springs and perchise (i have coils now) And will I need to get a different trans crossmeber or anything? And will I need to do something to my cab floor? ( its an automatic 2wd now)? And I have some full lenght hedmen hedders. Will those still work?
__________________
"A true hotrodder wouldn't be content untill he had created a car so violent, so hairy, so totally sick that the very act of dropping the hammer would result in instant death. Anything less results in the need to go faster." - Tony DeFeo Last edited by BowTieMan; 10-11-2005 at 02:45 AM. |
|
|
|
10-11-2005, 03:08 AM
|
#2 |
|
4 eyed fever
Join Date: Jul 2005
Location: Eureka, Nevada
Posts: 500
|
If your 2wd is a small block, it will have the low hump. 4wd and BB have the high hump. The hi hump bolts in and I think the low is one solid piece, so there will be some modification needed. Can't help with the rest. Someone more knowledgable will probably weigh in on this.
Al
__________________
1971 GMC 2500 4x4 1972 GMC Sierra Grande 1/2 t 4x4-#1 son's truck. Recently completed resto. 4 YO daughter," Daddy, I like your truck better than Mom's." (2000 F350-ranch truck) Smart kid!! |
|
|
|
|
10-11-2005, 05:38 AM
|
#3 |
|
Registered User
 
Join Date: Feb 2001
Location: East Central, MO
Posts: 11,336
|
I think that it has pretty much been determined here that the swap would be lots easier with a 4x4 frame and just swapping body parts. Swapping the parts over can be done but will take a lot of drilling and measuring. And yes the floor will need a high hump or u will need a body lift for the cab to clear the TC.
|
|
|
|
|
10-11-2005, 10:43 PM
|
#4 |
|
Junk/Daily Driver Club
Join Date: Feb 2004
Location: Manheim, PA 17545
Posts: 253
|
Like MUDDER67 said it will be a lot of work. I`m working on one right now that had a leaf spring rear under it. But then I`m also putting a Big Block in at the same time.
Good luck ! Willis
__________________
Daily Driver: 1970 C-20 400 sbc,sm-465,Dana 61 one ton SRW rear, 3.07 gears, locker.  There are three kinds of people: those who make things happen, those who watch things happen, and those who have no idea what happened! |
|
|
|
|
10-13-2005, 02:57 AM
|
#5 |
|
Senior Member
Join Date: Dec 2003
Location: Kingsport TN
Posts: 4,641
|
ABHaulR has a good right up on his web page about this PM him for ? . here is a link to his site. http://www.geocities.com/scbeoffroadunlimited/
__________________
Earl 68 2500 4x4 GMC Burb |
|
|
|
|
10-14-2005, 10:56 PM
|
#6 |
|
BlahBlahBlah
Join Date: Feb 2002
Location: Wa.
Posts: 19,816
|
too bad you arent closer i have a rolling 71 (disk brakes) 4x4 halfton long box chassis with auto tranny and transfer case still sitting in it. i paid 600 for it i would take 500. heck its down hill from washington to arizona. i could just point it your way and give it a shove.
|
|
|
|
|
10-21-2005, 09:18 PM
|
#7 | |
|
Designated A-hole!
Join Date: Mar 2003
Location: South Mississippi
Posts: 36,450
|
Re: Converting to 4x4
Quote:
__________________
"If it ain't broke, fix it 'til it is!" Being stupid ain't illegal.  We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck" |
|
|
|
|
|
10-22-2005, 10:10 AM
|
#8 |
|
Senior Member
Join Date: May 2004
Location: Binghamton, NY
Posts: 3,454
|
Re: Converting to 4x4
Too bad you weren't closer to here either. Freind of mine has a 71 3/4 4x4 for sale as well, open knuckle w/discs, 4 speed/205, Eaton rear with Detroit and 4:56s. CST interior, rusty but not too bad for $500.
__________________
2000 GMC CCSB 454/4L80 6” lift SAS 1999 Chevy CCSB 454/NV4500 6” lift 1999 GMC Yukon 350/4L60 4" SAS |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
