![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Active Member
![]() Join Date: Jun 2019
Location: Gaithersburg, MD
Posts: 110
|
Heat/Sound Deadening Plan - Opinions?
For the floor/rearwall I'm looking at the Flatline pre-cut butyl/aluminum foil kits (floor, wall), plus a layer of Siless Liner (closed cell foam), plus a layer of double-sided aluminum foil/cotton jute, then ACC mass-backed carpet.
For the roof I'm looking at Flatline pre-cut kit, plus a layer of Siless Liner, then the USA-1 Industries vinyl wrapped ABS plastic headliner. For the firewall I'm looking at the jute/board OEM-style pad. I'm planning to roll/brush 1-2 coats of Eastwoods rust encapsulator on the firewall and floor first. They are in good shape now. I'm also planning to add some seam sealer where the kick panel sheet metal meets the floor. Any advice? |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Oct 2018
Location: Ontario Peterborough
Posts: 764
|
Re: Heat/Sound Deadening Plan - Opinions?
No advice here , sounds like you got it under control .
|
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Oct 2013
Location: Alabama
Posts: 1,221
|
Re: Heat/Sound Deadening Plan - Opinions?
don't discount the doors. a TON of noise and heat/cold is transmitted thru the hollow doors. sound deadener on the backside of the door skin as well as under the door panel will do wonders to help quieten it down & help some with thermal insulation.
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 2,553
|
Re: Heat/Sound Deadening Plan - Opinions?
2nd on the doors being a large noise source. Replace all the rubber and glass channels.
Otherwise looks like a good plan. |
![]() |
![]() |
![]() |
#5 |
Active Member
![]() Join Date: Jun 2019
Location: Gaithersburg, MD
Posts: 110
|
Re: Heat/Sound Deadening Plan - Opinions?
Thanks all! Will definitely do the doors too.
Here's my progress so far. After removing the glued-on jute from the cowl area, and as much of the glue as I could get off, I painted the entire firewall with Eastwoods rust encapsulator. Then I added a layer of Siless closed cell foam to the cowl area, down to the firewall pad. The rectangular sheets are the perfect size for this job; they'll reach from the firewall up to the top of the cowl. Finally, I installed the cardboard-backed jute firewall pad. I got the pad from Repops. It fit size-wise well and most of the pre-made holes made sense, but it was half as thick as the original. I wasn't happy about that, so I glued on a layer of jute that is faced with aluminum foil front and back. I got the foil jute from Classic Industries. Together, the Repops pad and the foil jute matched the factory thickness. Also, the Repops pad came with plastic mounting plugs. I used new rubber ones. Here's a CRITICAL tip when installing the rubber mounting plugs: Debur the holes! If you don't, the ridge/burs on the holes will simply dig into the head of the plug and it won't go through, no matter how hard you try. A little grease might help too. Does anybody know how on Earth I'm supposed to install triangular column cover plate? I knocked out the hole in the pad for the column, but there's got to be more to it than that. |
![]() |
![]() |
![]() |
#6 |
Senior Member
![]() Join Date: Dec 2009
Location: TN.
Posts: 8,148
|
Re: Heat/Sound Deadening Plan - Opinions?
You have got it down pat.
I helped my Nephew do (About) the same thing. It made a Huge difference in the road noise and heat difference.
__________________
________________________________________________________________________________________ ____________________________________________ 84 Chevy K-20 63 Impala (my high school car) http://67-72chevytrucks.com/vboard/s...Crew Cab Build |
![]() |
![]() |
![]() |
Bookmarks |
|
|