67 Camaro Build

[7dee2]

Short back story to start the 67 Camaro build. We acquired this project car in June 2011, previous owner had had enough Camaro fun and listed it in the local online classifieds. Here’s what the car looked like in September 2007 about the time the PO purchased it. From the ad copy it sounds like it was in need of some metal work, which is exactly what the PO started with a local shop.

[7dee2]

After a bunch of $$$ (according to the PO during our negotiations) and the shop closing its doors the Camaro was left in mid metal repair. Here’s how it looked when we found it.

[7dee2]

New two-piece floor, new trunk floor, both lower front fenders, front window channel and some right rocker repairs have been completed.

[Dieselwrencher]

Man, she has had a lot of metal work done to her. I'm in to follow this, it's going to be sweet.

[7dee2]

Thanks Ryan I hope so!




Car came with lots of parts here’s a few pics of the piles… Took several loads to get it all to our place.

[Clyde65]

Big project right there, hopefully all the metal work is done to your satisfaction!
My buddy had 6 or 7 of these when We were kids....iirc, he built them all with his dad and then sold them off to fund his college.


Good luck and great project!!

[7dee2]

Thanks Clyde65, what’s been done looks pretty good so one of our first moves is going to be inspecting that work again to refresh the memory. You know a good friend of mine also restored a pair of 69’s back in the day, both were big block cars and if I remember correctly it paid for (or darn close) his house that they still live in today.



Once the car got here it went to the media blaster. Only damage that we’ve found not caused by rust and earlier body work is this spot on the left rear inner structure next to the quarter window.

[Dieselwrencher]

Nice. The less rust repair the better! Have any plans for solid sub frame mounts or sub frame connectors etc?

[7dee2]

I agree that would be nice! Perhaps or polyurethane (?), sub frame connectors for sure.


Hit it with the DA, bolted on some wheels and pushed it outside for some pics, looked pretty good from a few feet away. Here’s some close ups, plenty of area’s that still need attention.

[7dee2]

Car is getting full rear quarters, mini tubs, tail pan, etc., etc., etc.

[7dee2]

Shortly after that last round of pics we tore the car back down to a shell, I’d no idea it would be a little over 5 years to get back to it.

[Dieselwrencher]

Man, I'm so jealous. I can't leave anything bare metal for that long without doing more work.

Do you plan to race this car ot will it just be a tribute car? From the research I've done on the bushings, the polys still flex a bit. So racers recommend solid ones. I plan to auto cross mine so I think I'm going solid on it.

[7dee2]

Oh no, don’t be jealous, best way to describe the next maneuver is stupid is as stupid does... Yes, and no, not a dedicated race car (no roll cage) but a very fun street car with some time slips in the glove box!


Here’s pics of us pulling it out of storage a few months ago, some dingus (me?) put it away without sealing it up.

[7dee2]

It’s sporting a presidential tan these days!

[Dieselwrencher]

Are you going to spray acid on it or a rust converter or just sand it off? It still doesn't look bad though.

[7dee2]

It’s not that bad and would sand off (flash rust), probably will end up sanding some areas but with it getting rear quarters, etc. It’ll probably get media blasted one more time after we’re done with all the metal repairs.



I did have a red on red 67 Camaro (327, glide, 10 bolt) back in high school for a short time. Always wanted a 67 Camaro, big block, 4-speed day two-ish type drag car. The plan has always been a tribute car to Grumpy’s Toy III. Don’t know if we’ll actually letter the car but I like everything about one of the first big block Camaro’s. Here’s some pic’s of the actual restored car owned by the Mecum’s and back in the day with Da’ Grump & George Hurst.

[Dieselwrencher]

That will be really cool. I want another 4 speed car to drive around too. I miss it so bad!

[7dee2]

Thanks Ryan, banging gears is a pretty good time!



For the purists, and it’s just interesting to know how this particular Camaro was originally equipped when it left the factory, the dealer, who bought it and the delivery date (just had a B-Day).

Trim tag is still in place and we have the protect-o-plate, after decoding both and verifying it’s not anything really special (nice colors) I don’t feel bad about making into something better, IMO.

Trim Tag:
11 = Nov. B = 2nd Week R830 = Los Angles Plant Code#
ST 67- = 1967 12637 = Coupe, custom int. LOS = Van Nuys, CA. 8297 = Body #
TR 797-Z = Parchment custom buckets H-H = Mountain Green
W = Tinted Windshield 2G = Center Console 3K = RPO Z21, style trim group

Protect-O-Plate:
K = Parchment/Black (Carpet, instrument panel, and steering wheel are black)
HH = Mountain Green / Mountain Green
123377Lxxxxxx 1 = Chevrolet, 2 = Camaro, 3 = for 6-cylinder engine, 37 = coupe, 7 = 1967 model, L = Los Angeles, CA. xxxxxx = vehicle serial number sequence
B = Bay City (1 bbl/2 bbl))
F0922LN = F for Flint (MI) Motor Facility (L6 engines), 09 = month of year, 22 = day of month, LN = eng suffix code (without K19 (smog) 250ci/155HP L22 L6, 3- or 4-spd trans, no-A/C
PA1107G PA = 3.08 Ratio, 10 Bolt axle, 8.125 in. diameter ring gear, Non – Positraction, Standard Brake 11 = month of year, 07 = day of month, G = Detroit Gear & Axle plant
K = November 1966
S7P09 = Saginaw Manual 3-speed

[Dieselwrencher]

Very cool! I just got a 71 RS and I've been trying to find the build sheet to verify it is an RS. I only have 1 place left to look and I hope it's there. Other wise oh well. It's just a 307/PG car so it wouldn't be worth what a big block car would be. Haha

[rgunlock]

Just found that you'd started this thread. I'll be following. I drove a '69 Camaro my Sr. year and through college. Would love to get another one. For now I'll have to live vicariously through your build.

[7dee2]

Originally Posted by Dieselwrencher

Very cool! I just got a 71 RS and I've been trying to find the build sheet to verify it is an RS. I only have 1 place left to look and I hope it's there. Other wise oh well. It's just a 307/PG car so it wouldn't be worth what a big block car would be. Haha

Congrats good for you, I really like the RS frontend on second gens! Hope you find it, we have the build sheets for Blue and our C10, that stuff is just cool.

Originally Posted by rgunlock

Just found that you'd started this thread. I'll be following. I drove a '69 Camaro my Sr. year and through college. Would love to get another one. For now I'll have to live vicariously through your build.

Thanks Rick, I always appreciate your thoughts and comments.



Using a plumb bob and making marks on the floor the subframe has passed our simple squareness test. Pulled the old body mounts and found that the left rear mount is going to need some attention, but the rest are in really great shape.

[gringoloco]

Hey, a local Camaro build! Know where any more are hiding? We are looking for a 67-69 Camaro or 67-68 fastback Rustang

[ajviper]

Always nice to see Gen 1 cars being brought back to life.

[7dee2]

Originally Posted by gringoloco

Hey, a local Camaro build! Know where any more are hiding? We are looking for a 67-69 Camaro or 67-68 fastback Rustang

You betcha Chris! Don’t know of any personally but this 69 popped up on KSL a couple of days ago, https://www.ksl.com/auto/listing/4339502?ad_cid=4 might be something? Oops, and it's gone just that fast! That is where we found ours it was on KSL but they go really fast these days.

Originally Posted by ajviper

Always nice to see Gen 1 cars being brought back to life.

Thanks ajviper!




Time to say good bye to the wood cart its done its job and it’s just way to wobbly so, up, up and away! Using the same plumb bob technique and making marks on the floor the shell also passed the high-tech squareness test. While doing this and looking closely at all the alignment holes (firewall & frame rails) they are all original and mounted to original inner panels which have not been removed by any previous work.

[gringoloco]

Originally Posted by 7dee2

You betcha Chris! Don’t know of any personally but this 69 popped up on KSL a couple of days ago, https://www.ksl.com/auto/listing/4339502?ad_cid=4 might be something? Oops, and it's gone just that fast! That is where we found ours it was on KSL but they go really fast these days.

I called and texted on that as soon as I saw it. Poof, gone! We’ll keep looking.

Keep up the good work!