|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-30-2015, 06:12 PM
|
#1 |
|
Registered User
 
Join Date: Dec 2012
Location: Los Banos CA
Posts: 2,705
|
Front slip drive line gasket
Like the thread name states. I cannot find the little cork/fiber gasket that holds the grease on a front pRt of the slip driveline. Where the TC end attaches to the axle end. Sorry no picture at this time. But I have looked everywhere online. I am not sure about the name of the gasket. I hope someone understands what I am saying.
Thanks.
__________________
1956 Chevy Bel Air 2 door 1956 Chevy 210 4 Door 1970 K20 LWB project the Hulk build w/Supercharged 4.8L-ly2/4L60E HULK BUILD 1970 C10 Yellow/White Deluxe LWB w/ 5.3L-LC9/6L80E 1968 K10 LWB Dark green my son calls it "THE HULK Jr"HULK JR *SOLD* GO  GO!!!
|
|
|
|
05-31-2015, 06:52 PM
|
#2 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: Front slip drive line gasket
I do, check Denny's Driveshafts.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
05-31-2015, 07:24 PM
|
#3 |
|
Registered User
Join Date: Dec 2012
Location: Los Banos CA
Posts: 2,705
|
Re: Front slip drive line gasket
I looked all over. No one has information online about it. I will call when I get out of work
__________________
1956 Chevy Bel Air 2 door 1956 Chevy 210 4 Door 1970 K20 LWB project the Hulk build w/Supercharged 4.8L-ly2/4L60E HULK BUILD 1970 C10 Yellow/White Deluxe LWB w/ 5.3L-LC9/6L80E 1968 K10 LWB Dark green my son calls it "THE HULK Jr"HULK JR *SOLD* GO GO!!!
|
|
|
|
|
06-01-2015, 06:16 PM
|
#4 |
|
Registered User
Join Date: Dec 2012
Location: Los Banos CA
Posts: 2,705
|
Re: Front slip drive line gasket
Local drive line shop said they are called drive line dust caps.
this is link to Denny's Drive shaft dust cap
__________________
1956 Chevy Bel Air 2 door 1956 Chevy 210 4 Door 1970 K20 LWB project the Hulk build w/Supercharged 4.8L-ly2/4L60E HULK BUILD 1970 C10 Yellow/White Deluxe LWB w/ 5.3L-LC9/6L80E 1968 K10 LWB Dark green my son calls it "THE HULK Jr"HULK JR *SOLD* GO GO!!!
Last edited by First c10; 06-01-2015 at 06:30 PM. |
|
|
|
|
06-01-2015, 08:22 PM
|
#5 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
Re: Front slip drive line gasket
Learn something new everyday. Thanks!
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
