350 swap help - The 1947 - Present Chevrolet & GMC Truck Message Board Network

lukespence · 02-21-2018, 02:06 PM

Hey,

I am new to the whole 63 c-10 modding stuff and need some help. Recently bought a 63 chevy with a 283 in it and a 4 speed. We took out the old 283 and dropped in a 350. The 350 was out of a 68. so the engine mounts worked fine. the only problem is that with the engine bolted in there is still a gap between the bell housing and then block. whats up with that?

Thanks Luke

**Clyde65** · 02-21-2018, 03:01 PM

Is the converter seated properly?

Tried loosening motor mount bolts and perch bolts, then tighten the trans bolts?

shortstep60 · 02-21-2018, 03:40 PM

Get under your truck and see if you can move the tork converter. If you cant move the tork converter you don't have it all the way back in the trans.

rvrfoot · 02-26-2018, 08:19 PM

Quote:

Originally Posted by Clyde65

Is the converter seated properly?

Tried loosening motor mount bolts and perch bolts, then tighten the trans bolts?

They just read the 350 and thought it was a 350 thans.

**The Rocknrod** · 02-21-2018, 03:51 PM

If the torque converter is attached to the flywheel then to the crank . . .
As was said already - the torque converter is probably not seated correctly.

geezer#99 · 02-21-2018, 04:11 PM

Where did you guys read anything about an automatic tranny swap?
I read that he still has the 4 speed.
That needs to be clarified!
Then we can answer his question.
If he still has the 4 speed it’s likely the input shaft isn’t seated into the pilot bearing.

**The Rocknrod** · 02-21-2018, 04:19 PM

It's not my fault, I drink in the morning. Everybody knows that.

geezer#99 · 02-21-2018, 04:34 PM

Quote:

Originally Posted by The Rocknrod

It's not my fault, I drink in the morning. Everybody knows that.

But it’s afternoon and evening somewhere too!
I know that quandry.
So much beer, so little time!

**The Rocknrod** · 02-21-2018, 05:16 PM

Quote:

Originally Posted by geezer#99

But it’s afternoon and evening somewhere too!
I know that quandry.
So much beer, so little time!

Doc wont let me have beer anymore I'm too sweet if you know what I mean. But that Jack Daniels Green Label Mmm, Mmm, Mmmmm

lukespence · 02-21-2018, 05:28 PM

yes it is a manual 4 speed. used a clutch alignment tool beforehand. the engine is bolted up to the frame. so it should work. I think I just realized the problem. the flywheel on the engine is from when it had a t5 connected to it. is that the problem is that different.

geezer#99 · 02-21-2018, 06:37 PM

Shouldn’t matter.
Should slide right in.
You might need to reverse the process.
Bolt the bell to the motor and then slide the tranny in place.
Or hook up your clutch linkage so someone can depress the clutch to release the disc and let the tranny slide in.

61K10 · 02-22-2018, 03:40 PM

he said the engine is bolted to the mounts. bellhousing bolted down? Mounts in the forward holes?

Wrenchbender Ret · 02-22-2018, 05:47 PM

Some bell housings are for a 10 in. clutch. If you put a flywheel & 11 or 12 in clutch in it won't clear & leaves a gap.

02-21-2018, 02:06 PM	#1
lukespence Registered User Join Date: Feb 2018 Location: Austin Posts: 4	350 swap help Hey, I am new to the whole 63 c-10 modding stuff and need some help. Recently bought a 63 chevy with a 283 in it and a 4 speed. We took out the old 283 and dropped in a 350. The 350 was out of a 68. so the engine mounts worked fine. the only problem is that with the engine bolted in there is still a gap between the bell housing and then block. whats up with that? Thanks Luke

02-21-2018, 03:01 PM	#2
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,545	Re: 350 swap help Is the converter seated properly? Tried loosening motor mount bolts and perch bolts, then tighten the trans bolts? __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

02-21-2018, 03:40 PM	#3
shortstep60 Registered User Join Date: Nov 2013 Location: Mayetta, Kansas Posts: 439	Re: 350 swap help Get under your truck and see if you can move the tork converter. If you cant move the tork converter you don't have it all the way back in the trans.

02-21-2018, 03:51 PM	#5
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: 350 swap help If the torque converter is attached to the flywheel then to the crank . . . As was said already - the torque converter is probably not seated correctly. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

02-21-2018, 04:11 PM	#6
geezer#99 Registered User Join Date: Aug 2009 Location: Bowser Posts: 13,715	Re: 350 swap help Where did you guys read anything about an automatic tranny swap? I read that he still has the 4 speed. That needs to be clarified! Then we can answer his question. If he still has the 4 speed it’s likely the input shaft isn’t seated into the pilot bearing.

02-21-2018, 04:19 PM	#7
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: 350 swap help It's not my fault, I drink in the morning. Everybody knows that. __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

02-21-2018, 05:28 PM	#10
lukespence Registered User Join Date: Feb 2018 Location: Austin Posts: 4	Re: 350 swap help yes it is a manual 4 speed. used a clutch alignment tool beforehand. the engine is bolted up to the frame. so it should work. I think I just realized the problem. the flywheel on the engine is from when it had a t5 connected to it. is that the problem is that different.

02-21-2018, 06:37 PM	#11
geezer#99 Registered User Join Date: Aug 2009 Location: Bowser Posts: 13,715	Re: 350 swap help Shouldn’t matter. Should slide right in. You might need to reverse the process. Bolt the bell to the motor and then slide the tranny in place. Or hook up your clutch linkage so someone can depress the clutch to release the disc and let the tranny slide in.

02-22-2018, 03:40 PM	#12
61K10 Registered User Join Date: Feb 2012 Location: pleasant valley--placerville ca Posts: 3,039	Re: 350 swap help he said the engine is bolted to the mounts. bellhousing bolted down? Mounts in the forward holes? __________________ 1961 chevy K10 my build is------------61K10 build

02-22-2018, 05:47 PM	#13
Wrenchbender Ret Registered User Join Date: Oct 2005 Location: Overland Park, Ks. Posts: 5,228	Re: 350 swap help Some bell housings are for a 10 in. clutch. If you put a flywheel & 11 or 12 in clutch in it won't clear & leaves a gap.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.