TN Big Block Tig Welded Custom Exhaust.. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dhart · 06-15-2013, 06:31 PM

If you have or you are building a big block for a 67-72 C-10 I can tell you this is as nice of a professionally built exhaust system you will find.
It was built by a local high end fabricator here in Memphis and I can send you a link to his site if needed.
It was built for a high end 67- C-10 with a 565 fuel injected big block and it will fit fine on any standard short deck block and heads from 402-632.
It consists of 2 1/4 primary tubes, merge collectors to 3 inch Heddman x pipe and extensions. It was all hand tig welded, pipes are numbered and then sent out for jet hot coating.
I can tell you the fit is great with good ground clearance as well, two tubes go over the frame and plug access is excellent. This is not a one size fits most set of hookers, the build quality is as good or better than a set of Lemons headers.
The cost of this system was around 2000.00 It was used for around 2500 miles and pulled for a top shelf L/S swap.
I bought the engine and all associated parts that I am installing in my chevelle. I wanted to keep the exhaust for a future c-10 project but have decided to pass it on.
No issues with this one, no leaks, very very nice!
875.00 firm....... Reduced 750.00 plus shipping!
shipping 100.00 continental u.s.
Also these may very well fit 73-87 as they are very similar frame and cab setup.

VA72C10 · 06-15-2013, 06:38 PM

are there mufflers with it or just as shown? Does it go all the way to the rear or stop after the x in the pictures?

dhart · 06-15-2013, 06:48 PM

No mufflers, it was set up with Magnaflow 3 inch band clamped on with turn downs just in front of the rear diff. They can be taken over the rear or use just as they were set up previously. The truck they came off of had a braced Currie rear diff and stainless tank so over the rear would not work on it but again they can be finished whatever way you like as the muffler mount is in the right position.

darkhorse970 · 06-15-2013, 08:22 PM

Do you have any pics of it installed on the truck?
Posted via Mobile Device

dhart · 06-16-2013, 01:50 PM

Here is a link to the original build. After the engine work was complete a full frame off restoration was done all top shelf parts.
http://www.hotrodsolutions.net/ChevyC10page2.html

dhart · 06-18-2013, 09:15 PM

bump

dhart · 06-20-2013, 08:19 PM

To dA top
Posted via Mobile Device

dhart · 06-21-2013, 08:47 AM

Ttt
Posted via Mobile Device

dhart · 06-22-2013, 09:53 AM

back to da top

Critterman71 · 06-23-2013, 12:34 AM

Think these might fit a 71 3/4 ton?

dhart · 06-23-2013, 09:34 AM

I think they will, you can check with some other members but the frame and cab geometry is the same far as I know on 3/4 or half ton. I have never seen any parts that I scabbed off a 3/4 be any different besides hubs springs and such. Let me know it is a nice setup.
Posted via Mobile Device

dhart · 06-24-2013, 02:14 PM

back to da top

dhart · 06-26-2013, 10:59 AM

Look
Posted via Mobile Device

dhart · 06-27-2013, 09:12 PM

Back up top
Posted via Mobile Device

dhart · 06-29-2013, 10:24 PM

Weekend bump
Posted via Mobile Device

dhart · 06-30-2013, 03:27 PM

look look

dhart · 07-03-2013, 03:34 PM

Look!
Posted via Mobile Device

Critterman71 · 07-03-2013, 10:42 PM

I would love to have them as they will work on my 3/4 ton with a slight brake line mod on the drivers side but at a total of 975.00 ( and they are worth it for sure) I just cant swing it as I bought a high end transmission last week. Good luck on the sale.

dhart · 07-04-2013, 01:51 PM

Yep I understand I saw the Trans you bought very nice you will really enjoy the 4l80 if I didn't have this th400 and gear vendors that is what I would get that was a good price on it too there not inexpensive to build.
Make an offer on the exhaust if interested.......
Posted via Mobile Device

dhart · 07-12-2013, 10:26 PM

Back too da top
Posted via Mobile Device

dhart · 07-21-2013, 11:22 PM

lOOk

dhart · 08-11-2013, 10:42 AM

need exhaust?

dhart · 08-12-2013, 08:39 PM

Ttt
Posted via Mobile Device

dhart · 08-17-2013, 09:49 AM

back to da top

dhart · 09-07-2013, 02:58 PM

Reduced price! cant hardly but a set of Hooker Super Comp for this price!

06-15-2013, 06:31 PM	#1
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Big Block Tig Welded Custom Exhaust.. If you have or you are building a big block for a 67-72 C-10 I can tell you this is as nice of a professionally built exhaust system you will find. It was built by a local high end fabricator here in Memphis and I can send you a link to his site if needed. It was built for a high end 67- C-10 with a 565 fuel injected big block and it will fit fine on any standard short deck block and heads from 402-632. It consists of 2 1/4 primary tubes, merge collectors to 3 inch Heddman x pipe and extensions. It was all hand tig welded, pipes are numbered and then sent out for jet hot coating. I can tell you the fit is great with good ground clearance as well, two tubes go over the frame and plug access is excellent. This is not a one size fits most set of hookers, the build quality is as good or better than a set of Lemons headers. The cost of this system was around 2000.00 It was used for around 2500 miles and pulled for a top shelf L/S swap. I bought the engine and all associated parts that I am installing in my chevelle. I wanted to keep the exhaust for a future c-10 project but have decided to pass it on. No issues with this one, no leaks, very very nice! 875.00 firm....... Reduced 750.00 plus shipping! shipping 100.00 continental u.s. Also these may very well fit 73-87 as they are very similar frame and cab setup. Attached Images Last edited by dhart; 09-07-2013 at 02:56 PM. Reason: Reduced price!

06-15-2013, 06:38 PM	#2
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Big Block Tig Welded Custom Exhaust.. are there mufflers with it or just as shown? Does it go all the way to the rear or stop after the x in the pictures? __________________ Looking for a 67-72 swb or blazer project in or around VA.

06-15-2013, 06:48 PM	#3
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. No mufflers, it was set up with Magnaflow 3 inch band clamped on with turn downs just in front of the rear diff. They can be taken over the rear or use just as they were set up previously. The truck they came off of had a braced Currie rear diff and stainless tank so over the rear would not work on it but again they can be finished whatever way you like as the muffler mount is in the right position.

06-15-2013, 08:22 PM	#4
darkhorse970 Registered User Join Date: May 2009 Location: Monroe, LA Posts: 2,105	Re: Big Block Tig Welded Custom Exhaust.. Do you have any pics of it installed on the truck? Posted via Mobile Device __________________ Keith SOLD - 1963 C10 Short Fleet 350/700R4 4/6 drop 1967 GMC Super Custom - Short Fleet COPO concept w/427 BBC T-400 w/Doug Nash overdrive 4/6 Drop, Buddy Buckets, etc... Frame Off (In Progress) I call it "Vulgar Display of Power" 1980 Silverado Original paint 49k Original miles 4/6 drop Check out my build thread here: http://67-72chevytrucks.com/vboard/s...=1#post6209941

06-16-2013, 01:50 PM	#5
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Here is a link to the original build. After the engine work was complete a full frame off restoration was done all top shelf parts. http://www.hotrodsolutions.net/ChevyC10page2.html

06-18-2013, 09:15 PM	#6
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. bump

06-20-2013, 08:19 PM	#7
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. To dA top Posted via Mobile Device

06-21-2013, 08:47 AM	#8
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Ttt Posted via Mobile Device

06-22-2013, 09:53 AM	#9
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. back to da top

06-23-2013, 12:34 AM	#10
Critterman71 Registered User Join Date: Nov 2008 Location: Lansing Mi Posts: 642	Re: Big Block Tig Welded Custom Exhaust.. Think these might fit a 71 3/4 ton?

06-23-2013, 09:34 AM	#11
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. I think they will, you can check with some other members but the frame and cab geometry is the same far as I know on 3/4 or half ton. I have never seen any parts that I scabbed off a 3/4 be any different besides hubs springs and such. Let me know it is a nice setup. Posted via Mobile Device

06-24-2013, 02:14 PM	#12
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. back to da top

06-26-2013, 10:59 AM	#13
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Look Posted via Mobile Device

06-27-2013, 09:12 PM	#14
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Back up top Posted via Mobile Device

06-29-2013, 10:24 PM	#15
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Weekend bump Posted via Mobile Device



Register or Log In To remove these advertisements.

06-30-2013, 03:27 PM	#16
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. look look

07-03-2013, 03:34 PM	#17
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Look! Posted via Mobile Device

07-03-2013, 10:42 PM	#18
Critterman71 Registered User Join Date: Nov 2008 Location: Lansing Mi Posts: 642	Re: Big Block Tig Welded Custom Exhaust.. I would love to have them as they will work on my 3/4 ton with a slight brake line mod on the drivers side but at a total of 975.00 ( and they are worth it for sure) I just cant swing it as I bought a high end transmission last week. Good luck on the sale.

07-04-2013, 01:51 PM	#19
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Yep I understand I saw the Trans you bought very nice you will really enjoy the 4l80 if I didn't have this th400 and gear vendors that is what I would get that was a good price on it too there not inexpensive to build. Make an offer on the exhaust if interested....... Posted via Mobile Device

07-12-2013, 10:26 PM	#20
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Back too da top Posted via Mobile Device

07-21-2013, 11:22 PM	#21
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. lOOk

08-11-2013, 10:42 AM	#22
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. need exhaust?

08-12-2013, 08:39 PM	#23
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Ttt Posted via Mobile Device

08-17-2013, 09:49 AM	#24
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. back to da top

09-07-2013, 02:58 PM	#25
dhart Registered User Join Date: Dec 2009 Location: Memphis TN Posts: 102	Re: Big Block Tig Welded Custom Exhaust.. Reduced price! cant hardly but a set of Hooker Super Comp for this price!

Register or Log In To remove these advertisements.