The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current Classic GM Trucks Classifieds > The 1967-1972 Chevrolet & GMC Pickups Parts Board > Blazer and Suburban Stuff

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-26-2012, 01:19 AM   #1
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Hinge plates for 72 Blazer hatch

I have two sets of hinge plates for the inside of the hatch on a 72 double wall hatch. I'm not sure if they would fit a single wall as I have not seen a one with the hatch. One of mine was completely roached so I had new ones made. Making 6 was as cheap as 2 since the bending process was quite hairy. These are brand new 16 gauge re-pops from a local machine/sheet metal fab shop. They may be out by a thousandth or so but very usable!

I'm asking $60 apiece or $100 a set.
Attached Images
  
72K5NTX is offline   Reply With Quote
Old 02-27-2012, 10:47 PM   #2
woodymm3
Registered User
 
woodymm3's Avatar
 
Join Date: Mar 2008
Location: Oklahoma city
Posts: 490
Re: Hinge plates for 72 Blazer hatch

ok where do these go?
woodymm3 is offline   Reply With Quote
Old 02-27-2012, 11:35 PM   #3
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

Inside hatch where the hinges bolt up.
Attached Images
  
72K5NTX is offline   Reply With Quote
Old 03-02-2012, 12:30 AM   #4
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

ttt
72K5NTX is offline   Reply With Quote
Old 03-02-2012, 12:34 AM   #5
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

Will take $40 a piece or $80 a set.....
72K5NTX is offline   Reply With Quote
Old 03-15-2012, 10:31 PM   #6
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

ttt
72K5NTX is offline   Reply With Quote
Old 03-31-2012, 01:12 AM   #7
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

Any offers???
72K5NTX is offline   Reply With Quote
Old 06-11-2012, 11:35 PM   #8
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

Any body rebuilding a hatch could use these to make it like new, mine sagged really bad on one side due to these plates being too thin/rusted through, fixed it good as new.

Any offers???
72K5NTX is offline   Reply With Quote
Old 08-24-2012, 08:38 PM   #9
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

ttt ... any offers
72K5NTX is offline   Reply With Quote
Old 08-05-2013, 10:55 PM   #10
amcgeh01
Senior Member
 
amcgeh01's Avatar
 
Join Date: Jul 2009
Location: SoCal
Posts: 206
Re: Hinge plates for 72 Blazer hatch

Hmm, I would have to check my single wall and see if I have an issue existing there already.. Of course I am assuming it even has the same hinges but they may not..
__________________
********************************************
In-work on my 5.3L/4L65E/NP208 case conversion into a 1972 GMC JImmy 4x4... Not as simple as it looks folks..
amcgeh01 is offline   Reply With Quote
Old 08-05-2013, 11:10 PM   #11
72K5NTX
Registered User
 
72K5NTX's Avatar
 
Join Date: Jan 2012
Location: Dallas Tx
Posts: 59
Re: Hinge plates for 72 Blazer hatch

I think all the hatches have these in them. But like the picture shows, they are actually inside the top to reinforce the hinge mount. Mine were rusted to pieces and I couldn't get my hatch to line up properly. Luckily the previous owner had sanded/cut about a half an inch off the bottom of one side of the hatch so that it would at least look like it lined up. You can imagine some of the problems this caused after correction. Gotta love K5 remuddlers.
72K5NTX is offline   Reply With Quote
Old 08-06-2013, 12:05 AM   #12
Nermal67
Active Member
 
Join Date: Jun 2013
Location: Montrose Colorado
Posts: 129
Re: Hinge plates for 72 Blazer hatch

Wouldn't happen to have any latches and the loops that mount to the top by any chance? Thanks. Dave
Nermal67 is offline   Reply With Quote
Reply

Bookmarks

Tags
hatch, hinge, topper door


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:59 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com