76 Dana 44 Steering Arm - The 1947 - Present Chevrolet & GMC Truck Message Board Network

rano · 03-01-2011, 08:16 PM

I just picked a set of 76 Chevy 4x4 axles to put under my 55 pickup to replace some early 60s 4x4 axles. The front axle is a Dana 44 and the steering arm is missing. I need new studs, cone washers and nuts also. The stock arm would be within about 1-1/2" of the height if the pitman arm so an arm for a 4" plus lift will not work. Where can I find a stock arm, studs, cone washers and nuts?

71blazerdetroit · 03-01-2011, 08:55 PM

Everything but the arm , offroad design.
Then again, worth asking them if they have a stock arm laying around.

**Zoomad75** · 03-01-2011, 10:25 PM

Might need to go to a boneyard to pull one. Most that lifted a truck and installed the raised arm threw the old arm in the trashcan. I know I did.

rano · 03-03-2011, 07:10 PM

The studs are out. Found new studs, cones and nuts at Independent4x. Now working on finding a stock arm 73-78.

**special-K** · 03-04-2011, 09:07 AM

I'd post a WTB in the parts board. Let someone else do the hard work of pulling it

. Someone who installed a raised arm will have the stock one laying around. And,they were happy to pull it off to get their truck lifted

OldCreek · 03-04-2011, 02:04 PM

I'm pretty sure I've got a stock arm from my 71 K5 laying around at my barn. I held onto it in case I wanted to go back to stock height. It should be the same.

I'm not planning on heading over to the barn anytime soon, though. So, it may take a week or so to get it.... You could have it for the cost of shipping.

OldCreek · 03-04-2011, 02:05 PM

Btw, I highly recommend cross over steering...but if you've no lift...

rano · 03-05-2011, 09:05 AM

The knuckle steering arm I am looking for is GM #3979552 and is used from 1973-78 on 1/2 ton Dana 44s.

duallyjams · 03-08-2011, 09:05 AM

Quote:

Originally Posted by special-K

I'd post a WTB in the parts board. Let someone else do the hard work of pulling it

. Someone who installed a raised arm will have the stock one laying around. And,they were happy to pull it off to get their truck lifted

Do you have to be a supporting member to post a WTB ?

rano · 03-08-2011, 09:10 PM

Found a guy locally that has a stock arm he will sell me.

03-01-2011, 08:16 PM	#1
rano Registered User Join Date: Dec 2009 Location: Racine, WI Posts: 14	76 Dana 44 Steering Arm I just picked a set of 76 Chevy 4x4 axles to put under my 55 pickup to replace some early 60s 4x4 axles. The front axle is a Dana 44 and the steering arm is missing. I need new studs, cone washers and nuts also. The stock arm would be within about 1-1/2" of the height if the pitman arm so an arm for a 4" plus lift will not work. Where can I find a stock arm, studs, cone washers and nuts? __________________ 1955 Chevy 2nd Series Pickup, 4x4, 4 speed, from Arizona 1955 Chevy 210 Delray 283, 4 speed and 55 posi, old street racer 1967 Chevy Corvette 427/435 hp numbers matching, Top Flight 1973 Ford Bronco Hunting Rig Last edited by rano; 03-01-2011 at 08:16 PM.

03-01-2011, 08:55 PM	#2
71blazerdetroit Registered User Join Date: Oct 2010 Location: detroit, mi Posts: 67	Re: 76 Dana 44 Steering Arm Everything but the arm , offroad design. Then again, worth asking them if they have a stock arm laying around.

03-03-2011, 07:10 PM	#4
rano Registered User Join Date: Dec 2009 Location: Racine, WI Posts: 14	Re: 76 Dana 44 Steering Arm The studs are out. Found new studs, cones and nuts at Independent4x. Now working on finding a stock arm 73-78. __________________ 1955 Chevy 2nd Series Pickup, 4x4, 4 speed, from Arizona 1955 Chevy 210 Delray 283, 4 speed and 55 posi, old street racer 1967 Chevy Corvette 427/435 hp numbers matching, Top Flight 1973 Ford Bronco Hunting Rig

03-04-2011, 09:07 AM	#5
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: 76 Dana 44 Steering Arm I'd post a WTB in the parts board. Let someone else do the hard work of pulling it . Someone who installed a raised arm will have the stock one laying around. And,they were happy to pull it off to get their truck lifted __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 03-04-2011 at 09:07 AM.

03-04-2011, 02:04 PM	#6
OldCreek Registered User Join Date: Jan 2007 Location: Central Coast California Posts: 1,026	Re: 76 Dana 44 Steering Arm I'm pretty sure I've got a stock arm from my 71 K5 laying around at my barn. I held onto it in case I wanted to go back to stock height. It should be the same. I'm not planning on heading over to the barn anytime soon, though. So, it may take a week or so to get it.... You could have it for the cost of shipping. __________________ 1972 K20 Suburban 5.7/700r4/NP205 Dana 44/H052 Sold 1972 C10 5.3L/4L60E 12bolt 5Lug - Sold 1971 K5 Blazer 6.0L LQ9 4L60E NP205 Dana 44/H052!!! 1970 K3500 1ton CrewCab 8.1L/Allison1000/NP205 Dana 60/14B!!!! - Sold 1984 K10 SWB 7.4L/4L80e/NP208 Corp 10/12 bolt Sold 1988 V30 CCLB 7.4L/TH400/NP205/Dana 60/Dana 70/3.73!!! (Sold) 2003 K2500HD 8.1/Allison1000/NP263

03-01-2011, 10:25 PM	#3
Zoomad75 K5Camper Join Date: Mar 2004 Location: Pueblo, CO Posts: 1,513	Re: 76 Dana 44 Steering Arm Might need to go to a boneyard to pull one. Most that lifted a truck and installed the raised arm threw the old arm in the trashcan. I know I did. __________________ Rob Z. 1975 K5 350/465/205/D44/12b 4" lift on 35's- RIP 1991 K5 8.1L/NV4500/241/D44/14b FWC Camper

03-04-2011, 02:05 PM	#7
OldCreek Registered User Join Date: Jan 2007 Location: Central Coast California Posts: 1,026	Re: 76 Dana 44 Steering Arm Btw, I highly recommend cross over steering...but if you've no lift... __________________ 1972 K20 Suburban 5.7/700r4/NP205 Dana 44/H052 Sold 1972 C10 5.3L/4L60E 12bolt 5Lug - Sold 1971 K5 Blazer 6.0L LQ9 4L60E NP205 Dana 44/H052!!! 1970 K3500 1ton CrewCab 8.1L/Allison1000/NP205 Dana 60/14B!!!! - Sold 1984 K10 SWB 7.4L/4L80e/NP208 Corp 10/12 bolt Sold 1988 V30 CCLB 7.4L/TH400/NP205/Dana 60/Dana 70/3.73!!! (Sold) 2003 K2500HD 8.1/Allison1000/NP263

03-05-2011, 09:05 AM	#8
rano Registered User Join Date: Dec 2009 Location: Racine, WI Posts: 14	Re: 76 Dana 44 Steering Arm The knuckle steering arm I am looking for is GM #3979552 and is used from 1973-78 on 1/2 ton Dana 44s. __________________ 1955 Chevy 2nd Series Pickup, 4x4, 4 speed, from Arizona 1955 Chevy 210 Delray 283, 4 speed and 55 posi, old street racer 1967 Chevy Corvette 427/435 hp numbers matching, Top Flight 1973 Ford Bronco Hunting Rig Last edited by rano; 03-05-2011 at 09:06 AM.

03-08-2011, 09:10 PM	#10
rano Registered User Join Date: Dec 2009 Location: Racine, WI Posts: 14	Re: 76 Dana 44 Steering Arm Found a guy locally that has a stock arm he will sell me. __________________ 1955 Chevy 2nd Series Pickup, 4x4, 4 speed, from Arizona 1955 Chevy 210 Delray 283, 4 speed and 55 posi, old street racer 1967 Chevy Corvette 427/435 hp numbers matching, Top Flight 1973 Ford Bronco Hunting Rig



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.