LS1 into a 73 cheyenne - The 1947 - Present Chevrolet & GMC Truck Message Board Network

smokedat · 12-10-2009, 02:51 AM

I'm in the process of doing a swap. Ls1 from a 98 Camaro into a 1973 Chevy truck s/wheelbase.

Engine: LS1 from 98 Camaro, modified with LS6 heads, LS6 intake manifold, 5 pin mass air flow, twin horn air intake. comp cams kit LSR 281-289 113. Headers from Street & Performance. Taylor 10.4mm ignition wires. Full set of billet pullys

No heater or A/C unit

Transmition: 4L60E

ford 9"

Strage center section with 4.11 gears

Rear suspension : 4 link from ridetech with ridetech adj. coilovers

Exhaust: dual, headers from Street & Performance 2 1/2" collectors, Hooker aero chamber mufflers, on 2 1/2" pipes, stainless tips from Cherry Bomb

Radiator: Griffin aluminum with trans cooler, in/out water lines on passenger side. Trans cooler lines on driver side.

Gas Tank: I will be running only 1 16 gallon tank from a 87 with in tank fuel pump, reason for upgrade is for the in tank baffles so the engine wont starv.

Gauges: Autometer

Harness: stock harness and computer, modified harness and re-tuned computer

Brakes:2010 C6 Corvette style front- 14" 6 piston rear-13.5" 4 piston - master cylinder from Wilwood note: may encounter vaccum issues due to cam and massive breaks, if so i will run an electric vaccum canister

More to follow.....

smokedat · 12-10-2009, 02:56 AM

pics

smokedat · 12-10-2009, 03:02 AM

exhaust

smokedat · 12-10-2009, 03:07 AM

some more pics

BIG10 · 12-10-2009, 03:39 AM

Very nice.

rongstad · 12-10-2009, 09:52 AM

X 2................nice

thump16 · 12-10-2009, 10:10 AM

awesome

Mr.Scary · 12-10-2009, 10:28 AM

pure LS powa!!!!!!!

menace121978 · 12-10-2009, 10:44 AM

that is awesome!!

what fans are you going with? and how many miles are on the motor/trans? the heads look like they've been gone through and cleaned up. SWEET!! looking forward to updates!!

DuckyTLK · 12-10-2009, 12:42 PM

epicccccc..

very nice photog skills my friend.

cant wait to see this together

Contagious209 · 12-10-2009, 02:04 PM

Awesome project. It's going to be badass when done

mhicks · 12-10-2009, 02:09 PM

Lookin good!

Thealien · 12-10-2009, 02:10 PM

another subscribed thread

smokedat · 12-10-2009, 02:32 PM

Any recommendations on the electric fan? i think I'm gonna go with the Jegs single 16" S-Blade 2200 CFM puller. The engine and tranny had 70K+ miles.

smokedat · 12-10-2009, 02:39 PM

deleted double post

menace121978 · 12-10-2009, 02:40 PM

i'm planning on the same radiator... but i gotta look into this. http://hotrodlane.cc/77chevytruck/77chevy.htm

apparently you can order the fans to go with the radiator.

btw, (if you dont mind) how much did the radiator alone set ya back?

here's a couple more options too...
http://bertok.us/agreif/fans/fanstech.htm
http://www.chevytalk.org/fusionbb/sh...hp?tid/194489/

menace121978 · 12-10-2009, 02:41 PM

oh yea, the intake runners sure look clean for 70k!

how did you gettem looking like that??

smokedat · 12-10-2009, 02:43 PM

deleted double post

smokedat · 12-10-2009, 02:46 PM

deleted double post

smokedat · 12-10-2009, 02:48 PM

deleted double post

clinebarger · 12-10-2009, 05:23 PM

Those are not 98 model heads 97&98 LS1s had perimeter bolt valve covers VS the center bolts on the 99 & up

STOCKISH · 12-10-2009, 05:27 PM

Gonna be sick. Cant wait to start a LSX swap of my own.

77shortstep · 12-10-2009, 05:35 PM

great start cant wait to see it finished

3r!c84 · 12-10-2009, 05:38 PM

he said it has ls6 heads

clinebarger · 12-10-2009, 06:18 PM

There not LS6 heads either. LS6 heads have a 243 casting number. It looks like 799 on these or 79somthing

12-10-2009, 02:51 AM	#1
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	LS1 into a 73 cheyenne I'm in the process of doing a swap. Ls1 from a 98 Camaro into a 1973 Chevy truck s/wheelbase. Engine: LS1 from 98 Camaro, modified with LS6 heads, LS6 intake manifold, 5 pin mass air flow, twin horn air intake. comp cams kit LSR 281-289 113. Headers from Street & Performance. Taylor 10.4mm ignition wires. Full set of billet pullys No heater or A/C unit Transmition: 4L60E ford 9" Strage center section with 4.11 gears Rear suspension : 4 link from ridetech with ridetech adj. coilovers Exhaust: dual, headers from Street & Performance 2 1/2" collectors, Hooker aero chamber mufflers, on 2 1/2" pipes, stainless tips from Cherry Bomb Radiator: Griffin aluminum with trans cooler, in/out water lines on passenger side. Trans cooler lines on driver side. Gas Tank: I will be running only 1 16 gallon tank from a 87 with in tank fuel pump, reason for upgrade is for the in tank baffles so the engine wont starv. Gauges: Autometer Harness: stock harness and computer, modified harness and re-tuned computer Brakes:2010 C6 Corvette style front- 14" 6 piston rear-13.5" 4 piston - master cylinder from Wilwood note: may encounter vaccum issues due to cam and massive breaks, if so i will run an electric vaccum canister More to follow..... Attached Images Last edited by smokedat; 12-21-2010 at 01:56 AM.

12-10-2009, 02:56 AM	#2
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne pics Attached Images

12-10-2009, 03:02 AM	#3
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne exhaust Attached Images

12-10-2009, 03:07 AM	#4
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne some more pics Attached Images

12-10-2009, 03:39 AM	#5
BIG10 Registered User Join Date: Dec 2008 Location: Jenks, OK Posts: 314	Re: LS1 into a 73 cheyenne Very nice. __________________ Jay 1978 Big 10 Silverado, 355 + 700R4 + 3.42 + factory tach + A/C + dual tanks + working cruise control = awesome highway cruiser.

12-10-2009, 09:52 AM	#6
rongstad Future: 86 on GenIV power! Join Date: Jun 2009 Location: San Antonio, Texas Posts: 105	Re: LS1 into a 73 cheyenne X 2................nice

12-10-2009, 10:10 AM	#7
thump16 Registered User Join Date: Jul 2005 Location: Valdosta GA Posts: 708	Re: LS1 into a 73 cheyenne awesome

12-10-2009, 10:28 AM	#8
Mr.Scary Project Optimus Prime Join Date: Jan 2009 Location: Dallas, TX Posts: 346	Re: LS1 into a 73 cheyenne pure LS powa!!!!!!! __________________ 84 SWB work in progress 89 burb 1500 (parts pig) LOL 08 ford focus (I know, I know) Wifes car "I said it b4 and i'll say it agian wiring is my worst enemy":devil:

12-10-2009, 10:44 AM	#9
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: LS1 into a 73 cheyenne that is awesome!! what fans are you going with? and how many miles are on the motor/trans? the heads look like they've been gone through and cleaned up. SWEET!! looking forward to updates!! __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list

12-10-2009, 12:42 PM	#10
DuckyTLK Registered User Join Date: Nov 2009 Location: whoremond beach, Florida Posts: 14	Re: LS1 into a 73 cheyenne epicccccc.. very nice photog skills my friend. cant wait to see this together

12-10-2009, 02:04 PM	#11
Contagious209 Registered User Join Date: Aug 2009 Location: Stockton Posts: 68	Re: LS1 into a 73 cheyenne Awesome project. It's going to be badass when done __________________ 1973 custom delux 20 with 454 project 2000 dodge neon

12-10-2009, 02:09 PM	#12
mhicks Registered User Join Date: Jan 2004 Location: Weatherford,Tx Posts: 747	Re: LS1 into a 73 cheyenne Lookin good!

12-10-2009, 02:10 PM	#13
Thealien Senior Member Join Date: Jun 2007 Location: Pine Ridge Florida Posts: 4,125	Re: LS1 into a 73 cheyenne another subscribed thread

12-10-2009, 02:32 PM	#14
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 into a 73 cheyenne Any recommendations on the electric fan? i think I'm gonna go with the Jegs single 16" S-Blade 2200 CFM puller. The engine and tranny had 70K+ miles. Attached Images

12-10-2009, 02:39 PM	#15
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	LS1 Swap to a 73 cheyenne deleted double post Last edited by smokedat; 12-16-2009 at 01:59 AM.



Register or Log In To remove these advertisements.

12-10-2009, 02:40 PM	#16
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: LS1 into a 73 cheyenne i'm planning on the same radiator... but i gotta look into this. http://hotrodlane.cc/77chevytruck/77chevy.htm apparently you can order the fans to go with the radiator. btw, (if you dont mind) how much did the radiator alone set ya back? here's a couple more options too... http://bertok.us/agreif/fans/fanstech.htm http://www.chevytalk.org/fusionbb/sh...hp?tid/194489/ __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list Last edited by menace121978; 12-10-2009 at 02:43 PM.

12-10-2009, 02:41 PM	#17
menace121978 Registered User Join Date: Jan 2009 Location: orangevale, ca Posts: 3,626	Re: LS1 into a 73 cheyenne oh yea, the intake runners sure look clean for 70k! how did you gettem looking like that?? __________________ "Dennis the Menace" 1978 Silverado (2wd, 1/2 ton, short bed)complete nut & bolt frame off restomod LQ9/4L80E MY LS SWAP/FRAME OFF BUILD BOOK 2006 TBSS way too much to list

12-10-2009, 02:43 PM	#18
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 Swap to a 73 cheyenne deleted double post Last edited by smokedat; 12-16-2009 at 02:01 AM.

12-10-2009, 02:46 PM	#19
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 Swap to a 73 cheyenne deleted double post Last edited by smokedat; 12-16-2009 at 02:02 AM.

12-10-2009, 02:48 PM	#20
smokedat Registered User Join Date: Nov 2009 Location: santa paula Ca Posts: 772	Re: LS1 Swap to a 73 cheyenne deleted double post Last edited by smokedat; 12-16-2009 at 02:03 AM.

12-10-2009, 05:23 PM	#21
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: LS1 into a 73 cheyenne Those are not 98 model heads 97&98 LS1s had perimeter bolt valve covers VS the center bolts on the 99 & up

12-10-2009, 05:27 PM	#22
STOCKISH Formerly- 1972SuperCheyenne Join Date: Oct 2008 Location: Wake Forest NC Posts: 5,782	Re: LS1 Swap to a 73 cheyenne Gonna be sick. Cant wait to start a LSX swap of my own. __________________ --Josh My Build Thread:http://67-72chevytrucks.com/vboard/s...d.php?t=799218 A good crossthread is better than Loctite any day. Life is not about what you have, but who you have to share it with.

12-10-2009, 05:35 PM	#23
77shortstep Registered User Join Date: Nov 2009 Location: Lebanon, MO Posts: 215	Re: LS1 Swap to a 73 cheyenne great start cant wait to see it finished __________________ 77 CHEVY - SHORT BED STEP SIDE 2WD 02 CHEVY - EXT CAB SHORT BED Z71 7 INCHES OF LIFT

12-10-2009, 05:38 PM	#24
3r!c84 Badass Join Date: Jan 2009 Location: lox. fl Posts: 4,586	Re: LS1 into a 73 cheyenne he said it has ls6 heads __________________ Think outside the box? -84c10 (1stcar)→My Build← -00 Saturn 5spd drop a gear and disappear! 1/4:13:90

12-10-2009, 06:18 PM	#25
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: LS1 into a 73 cheyenne There not LS6 heads either. LS6 heads have a 243 casting number. It looks like 799 on these or 79somthing

Register or Log In To remove these advertisements.