The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-13-2010, 04:25 AM   #1
cppursell
Registered User
 
cppursell's Avatar
 
Join Date: Dec 2008
Location: San Francisco, CA
Posts: 144
Question High compression engine and pinging

Hey,

I just put in my '67 C10 a small block 350, with a non-stock cam and small chambered 283 heads on it. According to my cousin (which this engine is his), it has an 11.2:1 compression ratio. Last night, we got it in and started, and today I drove it around with 87 fuel. It runs smooth and strong and accelerates fine, but if I push a little more on the throttle it starts pinging. Any more pedal and it would start pinging and knocking worse (BTW this is with a 600cfm Edelbrock performer carb). I played around with the timing and it seems to run decent on 17 advanced for now. I plan to experiment with higher octane fuel, and:

I'd love your input on how I should go about with using higher octanes for this experimental engine. I don't know what to do to get rid of the pinging in this higher compression motor. I appreciate your help!

Tidbits:
I'm in CA, so all I can get is 91 (as far as I know). I do not know about octane boosters. There's a local airport where I could possibly try aircraft fuel.
cppursell is offline   Reply With Quote
Old 10-13-2010, 04:52 AM   #2
Hottrucks
Redefining LowBudget
 
Hottrucks's Avatar
 
Join Date: Mar 2009
Location: lebanon Cow Hampshire
Posts: 4,538
Re: High compression engine and pinging

aircraft/race fuel would be best but very pricey.....this motor maybe a bit over built for street use I would consider putting in thicker head gaskets to drop the compretion as much as I could...9.5:1 is as much as most can stand on 93 octane without pulling a bunch of timing out of them maybe down as low as 8 to12*(OH boy I'm gonna get flamed for that) being old school and been though this I have used trany fluid to slow the burn down (ouch I'm going to get it again)

Alot is going to depend on what your going to use the truck for???
__________________
1970 C10 CST fleetside 472 ....big dreams little cash...
SunShine Syndicate..

Mikes Sandwich Fair Run OCT 8th 2011
Hottrucks is offline   Reply With Quote
Old 10-13-2010, 07:14 AM   #3
SSedan64
Registered User
 
SSedan64's Avatar
 
Join Date: Oct 2008
Location: Macon, GA.
Posts: 89
Re: High compression engine and pinging

I think you have the wrong Heads for the engine. 283 Heads have tiny 1.72" Intake valves & chambers. Larger chamber & valve needed.
SSedan64 is offline   Reply With Quote
Old 10-13-2010, 07:52 AM   #4
cdowns
Senior Member
 
cdowns's Avatar
 
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
Re: High compression engine and pinging

dream on with 87octane
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane

MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF

DONT BELIEVE EVERYTHING YOU THINK

TAKE MY ADVISE;I DON'T USE IT ANYWAY
cdowns is offline   Reply With Quote
Old 10-13-2010, 08:25 AM   #5
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

17 degrees static is far too much initial advance. I'd start by setting the timing per the sticky.

But....it ain't gonna run on 87 octane at 11.2. It's going to take premium fuel with a splash of some sort of octane increaser - avgas, racing gas or an aftermarket booster.
Ticker is offline   Reply With Quote
Old 10-13-2010, 12:18 PM   #6
cppursell
Registered User
 
cppursell's Avatar
 
Join Date: Dec 2008
Location: San Francisco, CA
Posts: 144
Re: High compression engine and pinging

Quote:
Originally Posted by Hottrucks View Post
aircraft/race fuel would be best but very pricey.....this motor maybe a bit over built for street use I would consider putting in thicker head gaskets to drop the compretion as much as I could...9.5:1 is as much as most can stand on 93 octane without pulling a bunch of timing out of them maybe down as low as 8 to12*(OH boy I'm gonna get flamed for that) being old school and been though this I have used trany fluid to slow the burn down (ouch I'm going to get it again)

Alot is going to depend on what your going to use the truck for???
I'll try even lower timing for the heck of it. I have heard from another source that a few ounces of tranny fluid in the tank does work. I'll try that too.
This is my only vehicle and daily driver. My (stock) 350 got busted from an oil leak while driving, and this engine was the closest solution to getting my truck on the road again.
cppursell is offline   Reply With Quote
Old 10-13-2010, 12:21 PM   #7
cppursell
Registered User
 
cppursell's Avatar
 
Join Date: Dec 2008
Location: San Francisco, CA
Posts: 144
Re: High compression engine and pinging

Quote:
Originally Posted by Ticker View Post
17 degrees static is far too much initial advance. I'd start by setting the timing per the sticky.

But....it ain't gonna run on 87 octane at 11.2. It's going to take premium fuel with a splash of some sort of octane increaser - avgas, racing gas or an aftermarket booster.
OK, I'll try less advance. Sorry, what do you mean setting per the sticky?

Yes, I was thinking before I'd try premium with a booster. Will do.
cppursell is offline   Reply With Quote
Old 10-13-2010, 12:37 PM   #8
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

Quote:
Originally Posted by cppursell View Post
I have heard from another source that a few ounces of tranny fluid in the tank does work. I'll try that too.
I wouldn't; it's not going to increase the octane although it may slow the rate of combustion. One thing for sure - it's a solvent and it's going to raise all kinds of Hell with the carb.

Another option, not a great one - but workable - would be to go with a really thick head gasket. Going from an .028 to like an .056 or .060 would drop the CR into the 10.5 or so range which is a heckuva lot more reasonable and will probably run with full ignition advance on premium fuel...barely.

You end with with a horrifying quench, but this is all about making what you have work...
Ticker is offline   Reply With Quote
Old 10-13-2010, 12:38 PM   #9
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

Quote:
Originally Posted by cppursell View Post
what do you mean setting per the sticky?
See this post; long-winded but pretty good and although it looks a little intimidating it's not all that hard to do - and well worth a couple hours investment.

http://67-72chevytrucks.com/vboard/s...d.php?t=290498
Ticker is offline   Reply With Quote
Old 10-13-2010, 01:49 PM   #10
nd72c10
Registered User
 
Join Date: May 2007
Location: north dakota
Posts: 26
Re: High compression engine and pinging

Do you know anything about the engine that you just stuck these random heads onto? cam part #?

What is the casting number from the cylinder heads? How was it determined that they are small chambered 283 heads?
__________________
--------------------------
'72 C10 - 350, TH350 - blown headgasket, under construction
'84 K5 Blazer - 305, 700R4, Serpentine conversion, DD
'97 Tahoe 2DR 4X4 - 350, 4L60E, 3.73, SPORT
nd72c10 is offline   Reply With Quote
Old 10-13-2010, 05:08 PM   #11
cableguy0
Senior Member
 
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,950
Re: High compression engine and pinging

11.2-1 with iron heads is gonna to beat the pistons apart from all the pinging. DO NOT just go out and drive it even though its pinging. You will be sweeping the engine up when the internals exit via the window they make in the oil pan. Your best bet is to find something else to drive daily. You need over 100 octane to safely run that engine if it does indeed have 11.2-1 comp.Tickers suggestion will work also but if you pull those heads off to change gaskets you might as well just swap them for something with a more reason combustion chamber size.
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.
cableguy0 is offline   Reply With Quote
Old 10-13-2010, 05:21 PM   #12
pockets
Registered User
 
pockets's Avatar
 
Join Date: Sep 2010
Location: Broken Arrow, OK
Posts: 428
Re: High compression engine and pinging

I would go with the timing suggestions as well. The cam can play a lot into it as well. A slightly big (I know that is a bit ambiguous) cam can actually help as it will bleed off compression at lower RPMs, but that might not be a first fix.

11.2 is a tad high but not totally unreasonable, except for maybe those heads. even vettes nowadays run 11:1 and don't have to have 90+ octane fuel. My dad ran a 10.25:1 BBC for 17 years with only 87 octane and drove it all over the country.
__________________
Project Bad Karma
pockets is offline   Reply With Quote
Old 10-13-2010, 05:28 PM   #13
cableguy0
Senior Member
 
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,950
Re: High compression engine and pinging

there is no comparison between modern combustion chamber shapes in aluminum heads and the old tech of the 60's heads. You also have to keep in mind these are computer controlled engines with everything being monitored and adjusted constantly.
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.
cableguy0 is offline   Reply With Quote
Old 10-13-2010, 07:13 PM   #14
fastwillie 696969
~Rest In Peace~
 
fastwillie 696969's Avatar
 
Join Date: May 2005
Location: CALIFORNIA NOR CAL
Posts: 9,707
Re: High compression engine and pinging

retard the timing 4 to 8 degs
__________________
is it fast ? it has a lighting bolt donut?


B___H please, I can remove 90% of your so called "beauty" with a kleenex
fastwillie 696969 is offline   Reply With Quote
Old 10-13-2010, 08:30 PM   #15
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

Quote:
Originally Posted by cableguy0 View Post
there is no comparison between modern combustion chamber shapes in aluminum heads and the old tech of the 60's heads. You also have to keep in mind these are computer controlled engines with everything being monitored and adjusted constantly.
Totally different situation.

Last edited by Ticker; 10-13-2010 at 08:30 PM.
Ticker is offline   Reply With Quote
Old 10-13-2010, 11:45 PM   #16
GASoline71
"I ain't nobody, dork."
 
GASoline71's Avatar
 
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,959
Re: High compression engine and pinging

Quote:
Originally Posted by SSedan64 View Post
I think you have the wrong Heads for the engine. 283 Heads have tiny 1.72" Intake valves & chambers. Larger chamber & valve needed.
Yep...

Gary
__________________
'cuz chicks dig scars...

My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread.

The Rebuild of Creeping Death after the wreck

Quote:
Originally Posted by LONGHAIR View Post
I would never rebuild a 305.
Quote:
Originally Posted by prostreetC-10 View Post
I love using vacuum gauges as part of the carb tuning process. I hook the gauge to the inside of my garbage can and leave it there.
Quote:
Originally Posted by Marv D View Post
Remember Murphys 2nd law of mechanical relationships... "OPPOSING COMPONENTS ATTEMPTING TO OCCUPY THE SAME SPACE, AT THE SAME TIME, GENERALLY END UP OCCUPYING ADJOINING SPACE AT THE BOTTOM OF THE OIL PAN"
Quote:
Originally Posted by cableguy0 View Post
Its cheaper to listen to advice given when you ask for help than it is to ignore everyone and wait for carnage.
GASoline71 is offline   Reply With Quote
Old 10-14-2010, 10:27 AM   #17
LEEVON
Moderator
 
LEEVON's Avatar
 
Join Date: Jul 2006
Location: Ozark, MO
Posts: 4,888
Re: High compression engine and pinging

Just a thought...have you checked total timing? Could it be that you have too much mechanical and vacuum advance? Adjustable vacuum canisters are cheap, you can dial it back and get the total timing correct. I agree with the others, bring your initial back to about 12 degrees and see what happens. I run about 10.5:1 in my 350 and don't have detonation but then I make sure the total timing is in range too.
__________________
'20 Silverado Trail Boss ~ '17 Tahoe ~ '79 K15 Sierra Grande ~ '76 Blazer 2wd ~ '71 Cheyenne swb ~ '55 Pontiac Safari ~'50 3100 bagged ~ '80 Wife ~ Late model kids
LEEVON is offline   Reply With Quote
Old 10-14-2010, 04:49 PM   #18
cppursell
Registered User
 
cppursell's Avatar
 
Join Date: Dec 2008
Location: San Francisco, CA
Posts: 144
Re: High compression engine and pinging

Thanks for all your replies. I have yet to consider what everyone said, but I have an update: I filled up with 91 gas and used a Lucas 3x octane booster. After that I retarded the timing to 13 advanced. It runs much better now, with pinging only if I open the secondary barrels on the carb. I'll keep experimenting.
cppursell is offline   Reply With Quote
Old 10-14-2010, 06:47 PM   #19
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

Cool - but my only suggestion is stop experimenting until you get the timing set right as I noted previously.

It's not just about the initial timing but the total timing including advance, which from your description is where the issue is.
Ticker is offline   Reply With Quote
Old 10-14-2010, 08:56 PM   #20
GRX
Registered User
 
GRX's Avatar
 
Join Date: Jul 2010
Location: MD
Posts: 1,937
Re: High compression engine and pinging

Static & Dynamic compression are two different things. Have the cam specs?
__________________
1969 c-10 Step Side Long Bed. I-6 250cid = = 1969 Pontiac GTO hard top. 400, 4-speed.
GRX is offline   Reply With Quote
Old 10-14-2010, 09:52 PM   #21
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

On an engine of this type, putting in a "too big" cam to bleed off DCR just ends up with a generally crappy-running engine that doesn't detonate.

DCR is a useful concept - on an engine making > 1.4 HP/CID or so.
Ticker is offline   Reply With Quote
Old 10-14-2010, 10:01 PM   #22
bradh
Registered User
 
Join Date: Jan 2007
Location: Nebraska
Posts: 84
Re: High compression engine and pinging

If you get the total timing set and it still knocks try a cooler plug. If I'm not mistaken that's a .375 reach gasket type plug on 283 heads. A Champion RJ12YC should be in the ballpark.
bradh is offline   Reply With Quote
Old 10-14-2010, 10:05 PM   #23
cableguy0
Senior Member
 
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,950
Re: High compression engine and pinging

Bottom line is that for a couple hundred bucks you can do a head swap if you shop around and use stock parts. People are practically giving away old casting 350 heads. A quick valve job and resurface and 50 bucks in gaskets and your back on the road without risk of melting or shattering a piston. Your going to probably end up detuned to the point the engine will run like sh!t and not even be worth bothering to go wide open throttle anymore to finally get the pinging to stop with the heads you have currently
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member.
cableguy0 is offline   Reply With Quote
Old 10-15-2010, 12:10 AM   #24
Bad70sbchevy
Registered User
 
Bad70sbchevy's Avatar
 
Join Date: Aug 2009
Location: Newberry,FL
Posts: 277
Re: High compression engine and pinging

What about running a cam with a lot of overlap? I'm running 12:1 compression on 882 heads plus a 292 cam and I run it every day (its my daily driver) and still able to run on 93 (even on 87 it runs fine). This way it lowers your dynamic compression thus allowing you to run pump gas, but I'm no engine builder by any means so anybody please chime in if i'm wrong.
__________________
1970 Chevrolet C-10 w/355sbc
2010 Silverado Daily Driver
1971 Mercedes 280sl project car

Last edited by Bad70sbchevy; 10-15-2010 at 12:12 AM.
Bad70sbchevy is offline   Reply With Quote
Old 10-15-2010, 12:14 AM   #25
Ticker
Account Suspended
 
Join Date: Oct 2009
Location: Sammamish, WA
Posts: 2,404
Re: High compression engine and pinging

As previously noted, a cam with a lot of overlap on an engine making less than about 1.4 HP/CID just wastes power, gas and driveability. Your engine would make significantly more power (on the order of 10-15% or more) with a lower static CR and the RIGHT cam. And it would make far more power where it spends most of it's time - below 4500 RPM.

This isn't intended to be harsh, but using DCR to run a high static CR is just bad engine design on a low-power, low-RPM engine. It's a crutch to make a bad combo work - but it doesn't work well. 1 point of CR is worth maybe 1.5 - 3% MAX on an engine making less than 1.4 HP/CID or so...so shooting for high CR for a street engine *does not* make power. It's a design technique for high-powered racing engines that has made it's way into street design.

Last edited by Ticker; 10-15-2010 at 12:17 AM.
Ticker is offline   Reply With Quote
Reply

Bookmarks

Tags
283, 350, fuel, heads, octane


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:31 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com