![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Sep 2005
Location: Smith Mountain Lake Virginia
Posts: 1,537
|
HELP! Last minute Sunday night - TO Bearing problem
Hey all need some quick help,
All day work around the house - last few before dark, changed the throw out bearing - 72, 6 cylinder - I CAN NOT get the tranny back up to the bell housing - only 4 bolts - hangs up about 1 1/4" - I tried up, down, side to side, lower front, raise front, same on the other end - now have clutch pedal engaged (pedal depressed and held in with block) - even tried two bolts in bottom holes taking up any slack - didn't want to force so I stopped - Any help much appreciated (and the mosquito's are coming!!!!)
__________________
"A cat will almost always blink when hit between the eyes with a ball peen hammer" (you don't always have to state the obvious) Wear your PPE! You can eat with false teeth but you can't see with a false eye. 1959 Studebaker Silverhawk 350/400 1972 C10 L6 3OTT 2005 F350 - Built - whew! Last edited by Luvlegs; 05-20-2007 at 07:12 PM. |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Sep 2005
Location: Smith Mountain Lake Virginia
Posts: 1,537
|
Re: Last minute Sunday night - TO Bearing problem
ttt
__________________
"A cat will almost always blink when hit between the eyes with a ball peen hammer" (you don't always have to state the obvious) Wear your PPE! You can eat with false teeth but you can't see with a false eye. 1959 Studebaker Silverhawk 350/400 1972 C10 L6 3OTT 2005 F350 - Built - whew! |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Feb 2007
Location: Dallastown , Pa
Posts: 261
|
Re: Last minute Sunday night - TO Bearing problem
Turn the tail shaft on the tranny , sounds like the splines aren't lined up between the tranny and clutch
|
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Sep 2005
Location: Smith Mountain Lake Virginia
Posts: 1,537
|
Re: Last minute Sunday night - TO Bearing problem
Been trying that also - it didn't seem to make any "clicking" noises like it was almost catching.... I'll do it some more - any more ideas? I found two posts where guys used long bolts and just kept going around tightening them.... I'm afraid that might break something.....
__________________
"A cat will almost always blink when hit between the eyes with a ball peen hammer" (you don't always have to state the obvious) Wear your PPE! You can eat with false teeth but you can't see with a false eye. 1959 Studebaker Silverhawk 350/400 1972 C10 L6 3OTT 2005 F350 - Built - whew! |
![]() |
![]() |
![]() |
#5 |
I am a Referee of life.
Join Date: Jun 2000
Location: Greensboro N.C.
Posts: 13,993
|
Re: Last minute Sunday night - TO Bearing problem
Sounds like you haven't got the input shaft aligned with the crankshaft.Did you use an alignment tool when you pulled the tranny?It keeps the clutch disc splined hole centered with the crank hole for the input shaft.
That's the first thing that came to my mind.I did my first many years ago and did not know to do this.I spent 2 days on a simple job.
__________________
The 47-present Chevrolet and GMC Truck Message Board Network,it's owners,moderators,members,and associates of any type should not be held responsible for my opinion. You can't fix stupid,not even with duct tape. "My appearance is due to the fact that "GOD" does punish you for having too much fun!" Barrett-Jackson has perfected alchemy,they make rust into gold! "You can lead a horse to water but you can't saddle a duck" "Cleverly disguised as a 'Responsible Adult' "Sometimes your Knight in shining armor is just a retard in tinfoil" |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Apr 2007
Location: Hayward CA
Posts: 27
|
Re: Last minute Sunday night - TO Bearing problem
Did you dry fit the bearing before instolling ?
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: May 2005
Location: PA
Posts: 2,696
|
Re: Last minute Sunday night - TO Bearing problem
Use floor jacks if need be, and get the engine and trans as perfectly lined up as possible. If they don't go straight in, or with a slight twist, something is wrong. Get the trans out of the way, and look in to see if the clutch disk is somewhat centered with the pilot bearing.
Take your time getting it perfectly lined up. I've had them be a real PITA, and the next time, they fall together. |
![]() |
![]() |
![]() |
#8 |
Senior Member
![]() Join Date: Sep 2005
Location: Lewisville, Nc
Posts: 10,234
|
Re: Last minute Sunday night - TO Bearing problem
why is the pedel depressed? this will release the clucth disc causeing it no to line up
__________________
David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube |
![]() |
![]() |
![]() |
#9 | |
Registered User
Join Date: Nov 2006
Location: Monroe, WA
Posts: 87
|
Re: Last minute Sunday night - TO Bearing problem
Quote:
Yup. Pull them back apart a few inches, insert your clutch alignment tool, then release the clutch pedal and leave it that way. If you don't have your tranny's input shaft there to hold the disk in place and you release the pressure plate, the disk will fall down and you won't be able to put it back together. If you don't have the long bolts to make 'rails', you can still insert the lower bolts to get an idea of your alignment and then just measure the distances all around to make sure you're going in straight. |
|
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Sep 2005
Location: Smith Mountain Lake Virginia
Posts: 1,537
|
Re: Last minute Sunday night - TO Bearing problem
I called my dad - it's been 20 years since he's worked on one - I had to have it done before dark - he said "crank it over" and the try again... I hesitated, but said wth and did it - I got back underneath picked it up off the jack and it slid in.... done!
__________________
"A cat will almost always blink when hit between the eyes with a ball peen hammer" (you don't always have to state the obvious) Wear your PPE! You can eat with false teeth but you can't see with a false eye. 1959 Studebaker Silverhawk 350/400 1972 C10 L6 3OTT 2005 F350 - Built - whew! |
![]() |
![]() |
![]() |
Bookmarks |
|
|