![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Just Don't Stop!
![]() Join Date: Feb 2004
Location: Dallas
Posts: 1,239
|
Can someone measure the inside width of the wheeltub on a fleetside for me?
I just want to know the width of a fleetside bed stock. Like the dimension from the inner tub to the inner lip of the outer fender. I was wondering if there is any truth to the fleetsides have a more room than the stepside claim.
__________________
1968 C10 build in process TT LSA/6L90e/9" |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,947
|
FirstGen, they should be the same between the tubs. I can tget a measurement on my 68 after work for you if somebody doesn't beat me to it before then.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
![]() |
![]() |
![]() |
#3 |
Just Don't Stop!
![]() Join Date: Feb 2004
Location: Dallas
Posts: 1,239
|
I wonder what it would look like to tub a step side using fleet wheel tubs? I'm sure someone has done this, anyone have a pic?
Thanks Scoti!
__________________
1968 C10 build in process TT LSA/6L90e/9" |
![]() |
![]() |
![]() |
#4 | |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,947
|
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Nov 2004
Location: Moore, OK..73160
Posts: 207
|
just under 13" from inside edge of wheel tub to inside edge of bedside along arch. The inside of the bedside angles inward above the wheel arch and I didn't have a flashlight to look up in wheelwell to read tape. Hope it helps.
|
![]() |
![]() |
![]() |
#6 |
Just Don't Stop!
![]() Join Date: Feb 2004
Location: Dallas
Posts: 1,239
|
thanks for the reply. I think I will just use fleetside tubs. Scoti, do you have a set you want to sell me?
Thanks, Taylor
__________________
1968 C10 build in process TT LSA/6L90e/9" |
![]() |
![]() |
![]() |
#7 |
Got Big Block?
Join Date: Apr 2000
Location: West Texas
Posts: 1,510
|
First Gen, I've got a set. I'll email you some pics in the morning. Bad luck though, I just met up with a guy from Dallas (on Saturday) and swapped 12 bolts (car) that could've brought them back to you....
__________________
"Experience is what you get when you didn't get what you wanted." |
![]() |
![]() |
![]() |
Bookmarks |
|
|