The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-16-2016, 12:33 AM   #1
67ChevNut
Registered User
 
Join Date: Mar 2009
Location: Eagle Pass,
Posts: 195
Show me your Boyd Welding Gas Tank Connections

I bought this gas tank a while back and I am just getting ready to install it. I know there are fuel line kits to use with it, what I like to see is specific pictures of the fuel line connections, and what fittings were used. Trying to find out if I should buy a fuel line kit, or if there are other ways to connect it. Appreciate your replies.
Attached Images
  
67ChevNut is offline   Reply With Quote
Old 10-16-2016, 08:15 PM   #2
Clyde65
1965 Chevy C10, 2005 4.8L/4l60
 
Clyde65's Avatar
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,545
Re: Show me your Boyd Welding Gas Tank Connections

I don't have pix but I just got -6 Russell fuel line from summit for feed and return. 20' is how I bought mine. Since I have an external pump, I had to buy more fittings but that's what I did and used dual line rubber lined hose clamps every 18".

Hope this helps.
__________________
Clyde65

Rebuild of Clyde
http://67-72chevytrucks.com/vboard/s...84#post8338184

69 Aristocrat Lo Liner build
http://67-72chevytrucks.com/vboard/s...84#post7561684



support our troops!
Clyde65 is offline   Reply With Quote
Old 10-17-2016, 05:32 PM   #3
67ChevNut
Registered User
 
Join Date: Mar 2009
Location: Eagle Pass,
Posts: 195
Smile Re: Show me your Boyd Welding Gas Tank Connections

Thanks for the reply Clyde. I am contemplating different options right now, will look into yours. I went to Lowe's and bought a couple of fittings for my gas tank. Trying to see if I can do this without buying the complete fuel line kit. I noticed it doesn't have all the fittings I need so I will need to buy extra fittings if I go with the Tanks Inc EfI fuel line kit, or the Boyd Welding fuel line kit.

I want to do this as soon as possible. Looking at the twist-lok Russell fittings too. Just like to get a few more ideas. I will post whatever I ended up using. Thank you again.
67ChevNut is offline   Reply With Quote
Old 10-21-2016, 12:00 PM   #4
Jonce
Registered User
 
Jonce's Avatar
 
Join Date: Jul 2006
Location: Twin Cities, MN
Posts: 115
Re: Show me your Boyd Welding Gas Tank Connections

This is the setup I ran on my '71.

Diagram of parts


Parts


I used the original fuel line vent from and mounted it inside my drivers side step side wheel well using the existing bolts.


I hope that helps.

Edit: I don't have a LSx in my truck (yet) but I'm running the FiTech fuel injection with the Boyd Welding tank
__________________
__________________________________
1971 GMC Stepside
350HO Deluxe 330hp, TH350 w/Gear Vendors, 3.73 Eaton posi, Fitech EFI, Boyd's Welding Tank, Ridler wheels, ECE 4/6" drop, front/rear sway bar
________________________________
Jonce is offline   Reply With Quote
Old 10-23-2016, 06:38 PM   #5
solidaxel
Registered User
 
solidaxel's Avatar
 
Join Date: Dec 2002
Location: Cactus Patch So. Az
Posts: 4,749
Re: Show me your Boyd Welding Gas Tank Connections

Here is what I used, all the lines were from the Parker Store AN-6 and -8
Attached Images
  
__________________
53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD)
53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25
55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73
62 Solidaxle Corvette Roman Red (327
340hp 4spd 3:36) C4 & C5 suspension tube chassis
LS 3 4L70E
65 Corvette Coupe 327 350hp 4spd 4:11
78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42
2000 S-Type 3.0 (wife cruiser)
2003 GMC SCSB 5.3 4L60E 3:42
solidaxel is offline   Reply With Quote
Old 10-24-2016, 06:08 PM   #6
67ChevNut
Registered User
 
Join Date: Mar 2009
Location: Eagle Pass,
Posts: 195
Re: Show me your Boyd Welding Gas Tank Connections

Thanks for that diagram and the picture, I will probably use half of those parts listed. Pictures help a lot, thank you.

I have not done this yet, but I was also thinking on using hard aluminum 3/8 pipe, flare it and use new fittings on the ends, I like the braided fuel line though. Not sure which way exactly to go yet, I know I have to buy the corvette filter. Once I get that I'll connect the fuel lines.

Like to try to spend as little as possible, lol. I'll post pics once I am done.
67ChevNut is offline   Reply With Quote
Old 10-25-2016, 10:45 AM   #7
zach_carver
Registered User
 
zach_carver's Avatar
 
Join Date: Aug 2014
Location: Blue Ridge,GA
Posts: 508
Re: Show me your Boyd Welding Gas Tank Connections

I used Russel AN fittings and braided fuel line. I don't have exact parts list though.. I pieced mine together from summit. I used the internal Aeromotive pump with my vette FPR also. Worked great so far and no more gas fumes!
__________________
1965 C10 LS2/4l70, WHITE, 5/7 DROP

LINK TO SUPER SNOOPY C10 BUILD---> http://67-72chevytrucks.com/vboard/s...d.php?t=689283

1977 C10 SILVERADO HAWAIIAN BLUE, 5/5" DROP, LS6/4L80E

1976 CHEVY K5, 350/350, YUBA GOLD/SADDLE
zach_carver is offline   Reply With Quote
Reply

Bookmarks

Tags
boy, fittings, fuel, ls1, swap


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:34 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com