|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-29-2020, 03:15 AM
|
#1 |
|
Registered User
Join Date: Sep 2013
Location: Newton,N.C.
Posts: 317
|
Front spindles Center line question.
My Truck is a '71 with disc brakes, 5 lug 2wd.
It is already "seems" low in the front. Still a bunch of space between the fender lip and top of tire, but that might be the function of the 26" tall tires. But truck looks lower Than I'd think a stock 70's truck would be. So my question is, a stock front spindle Where is it in relation to the knuckles upper and lower mounting/ball joint. I am trying to figure out if someone already put drop spindles on it or not and not sure how to tell a stock knuckle from a dropped knuckle/spindle As I don't know what measurement the spindle center to upper ball joint mounting flange would be stock, and/or lower ball joint mounting flange to spindle center . Thanks. |
|
|
|
12-29-2020, 09:26 AM
|
#2 |
|
Senior Member
 
Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: Front spindles Center line question.
This should help .
 Always post pictures ( if possible ) with your questions ,It helps to get good answers . http://67-72chevytrucks.com/vboard/s...d.php?t=462976
__________________
 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop |
|
|
|
|
12-29-2020, 10:19 AM
|
#3 | |
|
Registered User
Join Date: Sep 2013
Location: Newton,N.C.
Posts: 317
|
Re: Front spindles Center line question.
Quote:
Thanks, that will help. Yes photo's are always a help. But vehicle and I are 2000+ miles away from each other ATM. |
|
|
|
|
|
12-29-2020, 01:47 PM
|
#4 |
|
The Older Generation
  
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,412
|
Re: Front spindles Center line question.
-
Someone may have cut 1 coil off of the front springs. That would drop it about 2" and it would be hard to tell to the casual viewer. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
|
|
|
|
12-29-2020, 01:53 PM
|
#5 |
|
Registered User
Join Date: Oct 2016
Location: Dallas Texas
Posts: 3,053
|
Re: Front spindles Center line question.
.
From Grumpy's post/link...drop spindle on right: -klb
__________________
67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi 07 335 sport turbo 6sp 94 Trans Am GT LT1 6sp posi -- sold after 22yrs 99 540 sport V8 6sp -- sold 73 240z L24 4sp -- given to friend 68 C10 step 350/350 3.73 open -- sold |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
