DBW Gas Pedal Adpater bracket for truck/suv pedal - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Hart_Rod** · 11-27-2014, 01:06 AM

DBW mounting bracket for 03-07 Truck/SUV Pedal

$120 Shipped via USPS (**adjusted 10/4/2022)

Paypal: robhartley@aol.com, enter "TPB" in message block.

*** All purchases now include: USPS shipping in CONUS, paypal fees and all the necessary hardware to install the pedal bracket. ***

After receiving many of requests for pedal bracket that will work with the 03-07 truck pedal, I fabricated this pedal bracket. This is a bolt in bracket that uses the 03-07 truck/SUV DBW pedal (may fit others) for the 67-72 LS conversions. Let me know if you have any questions or suggestions.

*****
GEN IV flat brackets for the 05+ Corvette Pedal can be found here: http://67-72chevytrucks.com/vboard/s...d.php?t=631165
*****

**** PEDAL MOUNT INSTALL INSTRUCTIONS ****

1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten.

2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit.

3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts.

4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket.

5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly.

6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly.

7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary.

8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly.

9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket.

NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly.

If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase!

**Hart_Rod** · 12-03-2014, 11:24 AM

bump

CustomK5 · 11-21-2015, 04:21 PM

Hello was wondering if these are still available doing a 5.3 swap out of a 05 in a 72 blazer

**Hart_Rod** · 11-21-2015, 07:32 PM

Quote:

Originally Posted by CustomK5

Hello was wondering if these are still available doing a 5.3 swap out of a 05 in a 72 blazer

Yes sir! $100 paypal robhartley@aol.com. Thanks!

ivanandjuri · 01-26-2017, 10:22 PM

Quote:

Originally Posted by Hart_Rod

bump

Do u still make these?
Posted via Mobile Device

ivanandjuri · 01-26-2017, 10:24 PM

Quote:

Originally Posted by ivanandjuri

Do u still make these?
Posted via Mobile Device

If so, I'll take one.
Posted via Mobile Device

**Hart_Rod** · 01-27-2017, 07:14 AM

Quote:

Originally Posted by ivanandjuri

If so, I'll take one.
Posted via Mobile Device

Yes I do! Price and PayPal info is in post #1.

**Hart_Rod** · 02-01-2017, 10:03 AM

Quote:

Originally Posted by ivanandjuri

If so, I'll take one.
Posted via Mobile Device

DBW mounting bracket for 03-07 Truck/SUV Pedal
$100 Shipped via USPS
Paypal: robhartley@aol.com, enter "TPB" in message block.

NC_John · 02-03-2017, 07:44 PM

Here's a bump for a solid little part. I had to notch mine to clearance for the back-half wiring plug but fits great. (I painted mine too)

**Hart_Rod** · 12-05-2014, 10:09 AM

3 brackets sold. 9 left.

**Hart_Rod** · 12-09-2014, 10:40 AM

5 brackets sold. 7 left.

**Hart_Rod** · 12-12-2014, 09:50 AM

6 brackets sold, 6 left.

**Hart_Rod** · 12-12-2014, 11:55 AM

**** INSTALL INSTRUCTIONS ****

Pedal mount instructions:

1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten.

2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit.

3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts.

4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket.

5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly.

6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly.

7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary.

8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly.

9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket.

NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly.

If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase!

205harleyman · 12-12-2014, 11:29 PM

I want one

**Hart_Rod** · 12-13-2014, 10:05 AM

Quote:

Originally Posted by 205harleyman

I want one

Sweet! PayPal information is in the first post of the thread. Let me know so I can ship it today.

**Hart_Rod** · 12-14-2014, 02:49 PM

Quote:

Originally Posted by smbrouss70

I want one Rob!

Shipped. THANKS!

Quote:

Originally Posted by 205harleyman

I want one

Do u still want one?

smbrouss70 · 12-13-2014, 03:21 PM

I want one Rob!

205harleyman · 12-20-2014, 07:53 PM

Sorry, I forgot about it, but just sent paypal

**Hart_Rod** · 12-23-2014, 01:04 PM

Quote:

Originally Posted by 205harleyman

Sorry, I forgot about it, but just sent paypal

No worries! It shipped yesterday. Thanks again.

R

**dayj1** · 01-04-2015, 12:33 AM

Bump for a great seller. The bracket installed easily and is a great time saver.

elimontfort · 01-06-2015, 12:45 PM

hi I was wondering if you have any brackets left?

**Hart_Rod** · 01-06-2015, 01:09 PM

Quote:

Originally Posted by elimontfort

hi I was wondering if you have any brackets left?

Yes I do! The price is 100.00, Paypal is robhartley@aol.com. Thanks!

Quote:

Originally Posted by dayj1

Bump for a great seller. The bracket installed easily and is a great time saver.

Thanks Jonathan!

Roz · 01-06-2015, 01:44 PM

Just got your PM, I'll take one well!

**Hart_Rod** · 01-06-2015, 01:50 PM

Quote:

Originally Posted by Roz

Just got your PM, I'll take one well!

Thanks!

Roz · 01-06-2015, 02:06 PM

Quote:

Originally Posted by Hart_Rod

Thanks!

PayPal sent!

12-03-2014, 11:24 AM	#2
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	Re: Gas Pedal Adpater bracket for truck/suv pedal bump __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

11-21-2015, 04:21 PM	#3
CustomK5 Registered User Join Date: Aug 2015 Location: Redding ca Posts: 17	Re: Gas Pedal Adpater bracket for truck/suv pedal Hello was wondering if these are still available doing a 5.3 swap out of a 05 in a 72 blazer

02-03-2017, 07:44 PM	#9
NC_John Registered User Join Date: Jul 2013 Location: Rockwell, NC Posts: 1,639	Re: DBW Gas Pedal Adpater bracket for truck/suv pedal Here's a bump for a solid little part. I had to notch mine to clearance for the back-half wiring plug but fits great. (I painted mine too) __________________ 1970 C-10 LWB "Blu" Instagram (current build pictures) 70_nc_c10

12-05-2014, 10:09 AM	#10
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	Re: Gas Pedal Adpater bracket for truck/suv pedal 3 brackets sold. 9 left. __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3 Last edited by Hart_Rod; 12-09-2014 at 10:53 AM.

12-09-2014, 10:40 AM	#11
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	Re: Gas Pedal Adpater bracket for truck/suv pedal 5 brackets sold. 7 left. __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3 Last edited by Hart_Rod; 12-09-2014 at 10:52 AM.

11-27-2014, 01:06 AM	#1
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	DBW Gas Pedal Adpater bracket for truck/suv pedal DBW mounting bracket for 03-07 Truck/SUV Pedal $120 Shipped via USPS (adjusted 10/4/2022) Paypal: robhartley@aol.com, enter "TPB" in message block. * All purchases now include: USPS shipping in CONUS, paypal fees and all the necessary hardware to install the pedal bracket. * After receiving many of requests for pedal bracket that will work with the 03-07 truck pedal, I fabricated this pedal bracket. This is a bolt in bracket that uses the 03-07 truck/SUV DBW pedal (may fit others) for the 67-72 LS conversions. Let me know if you have any questions or suggestions. * GEN IV flat brackets for the 05+ Corvette Pedal can be found here: http://67-72chevytrucks.com/vboard/s...d.php?t=631165 * PEDAL MOUNT INSTALL INSTRUCTIONS ** 1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten. 2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit. 3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts. 4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket. 5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly. 6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly. 7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary. 8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly. 9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket. NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly. If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase! Attached Images __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3 Last edited by Hart_Rod; 10-04-2022 at 10:54 AM. Reason: -

12-12-2014, 09:50 AM	#12
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	Re: Gas Pedal Adpater bracket for truck/suv pedal 6 brackets sold, 6 left. __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

12-12-2014, 11:55 AM	#13
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,860	Re: Gas Pedal Adpater bracket for truck/suv pedal ** INSTALL INSTRUCTIONS ** Pedal mount instructions: 1. Start by bolting your truck/SUV DBW pedal assembly to the mount bracket using the provided 3/4" 1/4-20 bolt. Do not tighten. 2. Next, loosely bolt the mount bracket to the firewall using the three nutserts in the firewall where the original pedal was mounted. You can do this by aligning the three pre-drilled holes on the right side of the mount bracket. Use three 3/4" 1/4-20 bolts to attach to the firewall that were included in your kit. 3. Next, align the left edge of the mount bracket with the raised vertical firewall brace. There are two pre-drilled holes on the top and bottom on the left edge that will be used as a guide to install the provided self-tapping bolts. 4. After you attach the left side of the mount bracket to the raised brace, you can tighten the three bolts on the right side of the bracket using a 7/16 socket. 5. When the pedal bracket is securely attached, you can adjust the pedal position as desired by moving the top of the DWB pedal assembly left or right. If necessary, there is also about 1/2" up or down adjustment from the slotted hole in the bottom of the DBW pedal assembly. 6. After you have the pedal in the position that you like, use a 7/16 socket to tighten the bottom bolt holding the DBW pedal assembly. 7. Next, you should actuate the pedal up and down to check for any interference in the movement. There shouldn't be any, but all the trucks are a little different so be sure to check. If there is any interference, loosen the bolt and adjust as necessary. 8. Once the DBW pedal assembly is adjusted, make sure the bottom bolt is tight and remove the mounting bracket and DBW pedal assembly from the firewall as one piece. This will hold the pedal in your desired position and allow you to drill the top hole to finish mounting the pedal assembly. 9. Next, mark the top pedal assembly hole using the DBW pedal assembly as a guide. Remove pedal assembly and then drill a 1/4" hole where previously marked. Re-install the pedal assembly with the provided 1/4" bolt and nut and tighten. This nut should be tacked in place, just like the one on the bottom, so that the DBW pedal assembly can be removed by itself without removing the entire pedal mount bracket. NOTE: If you don't have a welder, you can just tighten the top bolt and leave the DBW pedal on the bracket for reassembly. If you have any questions or suggestion about the installation, please let me know. Thanks for your purchase! Attached Images __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3 Last edited by Hart_Rod; 02-10-2015 at 04:08 PM.

12-12-2014, 11:29 PM	#14
205harleyman Registered User Join Date: May 2011 Location: birmingham, al Posts: 209	Re: Gas Pedal Adpater bracket for truck/suv pedal I want one __________________ 205harleyman 1972 K5 Blazer 2002 5.3 ltr engine and transmission Vintage Air 1999 tan leather bucket seats and console w/1999 back seat 20inch Torque Thrust Wheels Corvette Madrid Red with Tan Top Hope to be driving soon!!!

12-13-2014, 03:21 PM	#17
smbrouss70 Registered User Join Date: Sep 2003 Location: Rayne, LA Posts: 2,784	Re: Gas Pedal Adpater bracket for truck/suv pedal I want one Rob! __________________ Steven "If dogs don't go to heaven, when I die I want to go wherever they went." -- Will Rogers R.I.P. Oscar R.I.P. Ratchet 1967 Pontiac GTO - Dad was the Original Owner 1970 Chevy 2wd SWB "Oscar's Truck" 1970 Chevy 2wd Blazer "Ratchet's Blazer" 2013 Chevy 2500HD Crew Cab Duramax/Allison Z71 LTZ "Brown Sugar" 2017 Chevy Suburban "BDB" 2020 Chevy Blazer Premier "Foxy" Member of Louisiana Classic Truck Club (LCTC) Shop Build

12-20-2014, 07:53 PM	#18
205harleyman Registered User Join Date: May 2011 Location: birmingham, al Posts: 209	Re: Gas Pedal Adpater bracket for truck/suv pedal Sorry, I forgot about it, but just sent paypal __________________ 205harleyman 1972 K5 Blazer 2002 5.3 ltr engine and transmission Vintage Air 1999 tan leather bucket seats and console w/1999 back seat 20inch Torque Thrust Wheels Corvette Madrid Red with Tan Top Hope to be driving soon!!!

01-04-2015, 12:33 AM	#20
dayj1 Senior Member Join Date: Jul 2009 Location: Athens, AL Posts: 499	Re: Gas Pedal Adpater bracket for truck/suv pedal Bump for a great seller. The bracket installed easily and is a great time saver.

01-06-2015, 12:45 PM	#21
elimontfort Registered User Join Date: Jun 2011 Location: Sunbury, N.C Posts: 140	Re: Gas Pedal Adpater bracket for truck/suv pedal hi I was wondering if you have any brackets left?

01-06-2015, 01:44 PM	#23
Roz Registered User Join Date: Apr 2014 Location: Cleveland TN Posts: 31	Re: Gas Pedal Adpater bracket for truck/suv pedal Just got your PM, I'll take one well!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.