|
05-03-2007, 11:57 AM
|
#1 |
|
Active Member
Join Date: Oct 2006
Location: wi
Posts: 190
|
New paint on my 72
Just thought i would post a pic of my jimmy after i finished it. This was my first paint and body job. the pic is 3 years old. i haven't been able to work on the truck in almost 2 years now. however all the engine and interior is done. i still need doors though. only thing holding me up is the drive shaft issues i have.
|
|
|
|
05-03-2007, 12:01 PM
|
#2 |
|
Registered User
 
Join Date: Jan 2007
Location: Columbus, Ohio
Posts: 4,339
|
Re: New paint on my 72
Looks good - nice truck.
So close to finishing it up - It will look good once it is done  Tom |
|
|
|
|
05-03-2007, 12:18 PM
|
#4 |
|
SKINNY TIRES RULE!
Join Date: Sep 2001
Location: Bothell, WA
Posts: 11,049
|
Re: New paint on my 72
What's your driveshaft issue?
__________________
bouncytruck 1972 K5 The Hauler 1994 K1500 Suburban The Daily2010 Kia Soul Wife's Ride2014 Fiat 500L |
|
|
|
|
05-03-2007, 02:16 PM
|
#5 |
|
Sofa King. We, Todd, Ed.
Join Date: Oct 2006
Location: Spokane, Wa.
Posts: 631
|
Re: New paint on my 72
Looks great, I'm surprised I dont see many black Blazers. Me likey.
__________________
~John 71 Blazer One Ton 65 Chevelle Station Wagon x2 59 Belair 2 Door 71 Chevy Open Road Van RV www.myspace.com/johnnywagon |
|
|
|
|
05-03-2007, 02:25 PM
|
#6 |
|
Active Member
Join Date: Oct 2006
Location: wi
Posts: 190
|
Re: New paint on my 72
the driveshaft u-joints will brake if i let the clutch out to fast. i have a 400 sbc .030 over with 10:1 compression. all the geometry is correct. no lift. and all parts were installed properly. i just gona upgrade all the yokes and joints.
Also, its not exactly black. its black cherry. it came off a 1982 gm car. i have been told a monty and also a caddy, but i aint to sure. |
|
|
|
|
05-03-2007, 03:03 PM
|
#7 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
|
Re: New paint on my 72
[QUOTE=gmcman7202;2156636]the driveshaft u-joints will brake if i let the clutch out to fast. i have a 400 sbc .030 over with 10:1 compression. all the geometry is correct. no lift. and all parts were installed properly. i just gona upgrade all the yokes and joints. QUOTE]
Pretty odd, they of course should be able to handle that. Are we just talking the rear driveshafts or are you doing that with it in 4wd? Good looking K5!
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
05-03-2007, 03:45 PM
|
#8 |
|
The LuvShack Garage
Join Date: Jan 2004
Location: Maple Grove, TN (West Side)
Posts: 30,475
|
Re: New paint on my 72
Nice
__________________
Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T |
|
|
|
|
05-03-2007, 04:55 PM
|
#9 |
|
I'm a poor spectator
Join Date: Aug 2006
Location: San Antonio, Tx
Posts: 2,287
|
Re: New paint on my 72
Don't rev it up so high
 . Also, you don't need doors to drive it.
__________________
2006 Jeep Unlimited IMPACT ORANGE 1993 Chevy 2500 4x4 ExCab LWB 454/NV4500 Tow rig  1977 Ford F100 2x4 LWB 1st truck I owned, still have it!!! 1979 Ford F150 4x4 SWB Built Ford Tough!!!  1971 Chevy Blazer 350 / SM465 / NP205 UNDER CONSTRUCTION Soon to have a LQ4 6.0!!! |
|
|
|
|
05-03-2007, 05:13 PM
|
#10 |
|
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,452
|
Re: New paint on my 72
Black Cherry, that sounds nice. Don't think I saw that before...More Pics, more pics.
Now that I look at it again, I see a slight red in the front fender where the sun hit it...coooooooooooooooooooool
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 05-03-2007 at 05:14 PM. |
|
|
|
|
05-03-2007, 05:18 PM
|
#11 |
|
Active Member
Join Date: Oct 2006
Location: wi
Posts: 190
|
Re: New paint on my 72
just the rear driveshaft. its got a sm465 with 3.73 posi and 33" tires. Also i am not reving it up that high. i have never gone above 5000 with the engine rpms and never let the clutch out anywhere near that. as far as 4wd, i dont have a front driveshaft.
|
|
|
|
|
05-04-2007, 10:51 AM
|
#12 |
|
Post Whore
Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,683
|
Re: New paint on my 72
Hmmm, that's pretty odd. Hope the upgrade solves the problem - just doesn't make any sense why your having that issue at all.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
|
|
|
|
05-04-2007, 10:55 AM
|
#13 |
|
Registered User
Join Date: May 2005
Location: Colorado
Posts: 138
|
Re: New paint on my 72
Is the engine bogging down before the u-joints break?? I'm wondering if maybe the rear-end is locked up. A torqie motor like a 400 is definitely strong enough to break stock u-joints when there is no give from the axle.
Awesome paint job by the way.
|
|
|
|
|
05-04-2007, 11:31 AM
|
#14 |
|
Active Member
Join Date: Oct 2006
Location: wi
Posts: 190
|
Re: New paint on my 72
no the engine does not bog down. i have broken the joints 3 times. first time was trying to break the tires loose, the other 2 i just let the clutch out a little fast on dry pavement. i am afraid to get stuck somewhere again.
Now here is the question. 1350 or 1410 series, as i understand 1310 are already on it. also, any special place to get the stuff from? Thanks guys for the comments and help. |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
