The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-08-2012, 07:07 PM   #1
Spassmacher
Registered User
 
Join Date: May 2011
Location: Portland, Oregon
Posts: 26
Is a 750 carb too big for a 327?

There's a good price on Edelbrock 1407 Performer series 750 cfm carb right now, but I was wondering if it's too big for my 327. I went the Vortec route w/ appropriate Edelbrock intake. I don't have the specs on my engine on me, but it's built up pretty well. I hear different things about whether 750 is too big for a 327, but i think I'm up over 400hp (if only barely) with my setup. What has been your guys' experience with this?
Posted via Mobile Device
Spassmacher is offline   Reply With Quote
Old 03-08-2012, 07:07 PM   #2
ProStreet68SB
The Engine Whisperer
 
ProStreet68SB's Avatar
 
Join Date: Sep 2006
Location: Ohio
Posts: 770
Re: Is a 750 carb too big for a 327?

YES YES YES! It's way to big!
ProStreet68SB is offline   Reply With Quote
Old 03-08-2012, 07:18 PM   #3
kriswvu1202
Registered User
 
kriswvu1202's Avatar
 
Join Date: Sep 2011
Location: Morgantown, WV
Posts: 111
Re: Is a 750 carb too big for a 327?

The way to accurately size a carburetor for an aplication is to take the cubic inches divided by 2 multiplied by the maximum RPM over 1,728. (327/2 x 6,500/1,728) = 615.017. The biggest carb your engine will need is a 650 cfm, and unless you plan on running wide open, high rpm all the time, a 600 cfm will be plenty. Plus, with a smaller carb, the throttle response is much better. The P.O. of my truck put a 750 cfm Edelbrock on the original 307. It ran fine, but was an absolute dog when you put your foot in it. Just bogged and accelerated lazily. I switched to a 600 cfm Holley and the difference was like night and day. Much crisper and when you stomp it, it goes right now...That said, I have a nice 750 cfm Edelbrock performer I'll sell you cheap. HAHA
__________________
"And when you discover what you will be in your life, set out to do it as if God Almighty called you at this particular moment in history to do it. Don't just set out to do a good job. Set out to do such a good job that the living, the dead or the unborn couldn't do it any better." -MLK
kriswvu1202 is offline   Reply With Quote
Old 03-08-2012, 08:15 PM   #4
ProStreet68SB
The Engine Whisperer
 
ProStreet68SB's Avatar
 
Join Date: Sep 2006
Location: Ohio
Posts: 770
Re: Is a 750 carb too big for a 327?

Quote:
Originally Posted by kriswvu1202 View Post
The way to accurately size a carburetor for an aplication is to take the cubic inches divided by 2 multiplied by the maximum RPM over 1,728. (327/2 x 6,500/1,728) = 615.017. The biggest carb your engine will need is a 650 cfm, and unless you plan on running wide open, high rpm all the time, a 600 cfm will be plenty. Plus, with a smaller carb, the throttle response is much better. The P.O. of my truck put a 750 cfm Edelbrock on the original 307. It ran fine, but was an absolute dog when you put your foot in it. Just bogged and accelerated lazily. I switched to a 600 cfm Holley and the difference was like night and day. Much crisper and when you stomp it, it goes right now...That said, I have a nice 750 cfm Edelbrock performer I'll sell you cheap. HAHA
That is all very true. Also remember that equation is designed for motors that are 100% volumetric efficient. Most street motors are lucky to be around the 80% range.
ProStreet68SB is offline   Reply With Quote
Old 03-09-2012, 05:42 AM   #5
GASoline71
"I ain't nobody, dork."
 
GASoline71's Avatar
 
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,947
Re: Is a 750 carb too big for a 327?

Find a Holley 1850 (600cfm).

You'll be very happy...

Gary
__________________
'cuz chicks dig scars...

My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread.

The Rebuild of Creeping Death after the wreck

Quote:
Originally Posted by LONGHAIR View Post
I would never rebuild a 305.
Quote:
Originally Posted by prostreetC-10 View Post
I love using vacuum gauges as part of the carb tuning process. I hook the gauge to the inside of my garbage can and leave it there.
Quote:
Originally Posted by Marv D View Post
Remember Murphys 2nd law of mechanical relationships... "OPPOSING COMPONENTS ATTEMPTING TO OCCUPY THE SAME SPACE, AT THE SAME TIME, GENERALLY END UP OCCUPYING ADJOINING SPACE AT THE BOTTOM OF THE OIL PAN"
Quote:
Originally Posted by cableguy0 View Post
Its cheaper to listen to advice given when you ask for help than it is to ignore everyone and wait for carnage.
GASoline71 is offline   Reply With Quote
Old 03-09-2012, 10:59 AM   #6
prostreetC-10
My Carbon Footprint
 
prostreetC-10's Avatar
 
Join Date: Oct 2008
Location: Orygun
Posts: 5,527
Re: Is a 750 carb too big for a 327?

Agree with the above. Just remember the cfm calculator is just to get you into the ball park. There are a lot of variables in correctly picking the right carb though. 400hp is a lot of HP out of a 327. The Corvette 375hp 327 L84 was a nasty motor. You would have to have some pretty serious compontent to be in that range with a compression that is almost not streetable. How do you arrive at the 400 HP? Cool thing about a well built 327 is you can pull those rpms to the moon!
prostreetC-10 is offline   Reply With Quote
Old 03-09-2012, 11:52 AM   #7
OC 72
Registered User
 
OC 72's Avatar
 
Join Date: Dec 2011
Location: CA
Posts: 361
Re: Is a 750 carb too big for a 327?

Absolutley! I had a 750 on my 327 hot rod...had it jetted down..still too much. Ran a 600cfm and worked perfect!
OC 72 is offline   Reply With Quote
Old 03-09-2012, 12:20 PM   #8
j1970GMC
Registered User
 
Join Date: Aug 2010
Location: Northern CA
Posts: 185
Re: Is a 750 carb too big for a 327?

I think a 750 is too big. I have a David Vizard book that talks about a 750 on a small block, but it's really complicated, and he's building efficient, powerful engines. I didn't go that route because I'm not David Vizard.

I had an 750 Edelbrock 1411 on my 350. Ran like a pig but with a lean feeling spot when the secondaries opened. Jetted it with a calibration kit and no better. Talked to Edelbrock and they said that if I could make it work then I should call them to let them know how I did it (they were NOT rude, in fact they had excellent customer service). I switched to a Holley 670 Street Avenger I bought from a friend (which I think is actually more like a 600, per my conversation with the Holley tech) and it runs great.

I have an Edelbrock 1406 (600cfm) on my 327 and it runs great and still seems a little rich to me, although I have not tried to jet it yet so I could be wrong.
j1970GMC is offline   Reply With Quote
Old 03-09-2012, 02:08 PM   #9
SeventyOne
Registered User
 
Join Date: Mar 2007
Location: Oakland, Ca
Posts: 1,382
Re: Is a 750 carb too big for a 327?

Quote:
Originally Posted by kriswvu1202 View Post
The way to accurately size a carburetor for an aplication is to take the cubic inches divided by 2 multiplied by the maximum RPM over 1,728. (327/2 x 6,500/1,728) = 615.017.
Your equation is technically right, but you're doing way too much math.

327 x 6500 / 3456 = 615.017

CID x Max RPM / 3456 = CFM

No need for that extra division by 2.
SeventyOne is offline   Reply With Quote
Old 03-09-2012, 03:04 PM   #10
jhngardner367
Registered User
 
jhngardner367's Avatar
 
Join Date: Feb 2012
Location: Austin, Arkansas
Posts: 248
Re: Is a 750 carb too big for a 327?

Where does the 3456 # come from?
__________________
Always expect the unexpected,....but don't expect the unexpected to be the unexpected you expect !
I'm busier than a one-legged cat,in a sandbox!
Veteran..and proud !
I can't fix what ain't broke....you want I should break it?
jhngardner367 is offline   Reply With Quote
Old 03-09-2012, 03:18 PM   #11
SeventyOne
Registered User
 
Join Date: Mar 2007
Location: Oakland, Ca
Posts: 1,382
Re: Is a 750 carb too big for a 327?

Well like I just simplified the equation posted above, I am sure the 3456 is some formulation of air volumetrics, x Pi x the moons gravitational pull, etc, simplified down to a simple number...being 3456.

I have also seen the equation with an additional step...multiplying by a coefficient of efficiency. Most carbs/setups being only 85% efficient so you would then multiply the 615.xx cfm by .85 to give you a closer number.

Racing setups or blown applications might raise the coefficient to 1.1. 615.xx cfm x 1.1.

But it won't REALLY matter. just leave that step out and you're in the ballpark. It's not like someone actually makes a carb that fits your equation number EXACTLY...I mean can you go out and buy a 522.xx cfm or 676.xx carb?
SeventyOne is offline   Reply With Quote
Old 03-09-2012, 03:44 PM   #12
SeventyOne
Registered User
 
Join Date: Mar 2007
Location: Oakland, Ca
Posts: 1,382
Re: Is a 750 carb too big for a 327?

Good read on the explanation of the equation:

http://www.dragzine.com/tech-stories...e-combination/
SeventyOne is offline   Reply With Quote
Old 03-10-2012, 07:56 AM   #13
wakeup
Registered User
 
Join Date: Mar 2012
Location: Havelock, NC
Posts: 10
Re: Is a 750 carb too big for a 327?

I agree with most of the others above, it's probably more than that engine needs.

I've got a Edelbrock 1406 (600cfm) on my 383 and it turns 6000 rpm and feels strong!
__________________
-1984 K10 Custom Deluxe 383, Turbo 400, NP208, 44/12 Bolt. 6/3 lift, 36 TSL's, In need of some TLC
-1990 R20 Suburban 6.2, Turbo 400, Whatever came under the rear end. Totally stock, no rust, not pretty
-2008 TrailBlazer SS, Stock since new, 3SS, All black, if you want it, let me know!
wakeup is offline   Reply With Quote
Reply

Bookmarks

Tags
327, 750, carb, edelbrock, sbc


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:12 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com