|
02-25-2014, 07:01 PM
|
#1 |
|
Registered User
Join Date: Oct 2012
Location: Greely, On, Canada
Posts: 89
|
Spindle Problem
I installed a set of CPP drop spindles (bought thru Borthers Truck) on my truck recently and one side (rf) sits higher up on the Ball Joint than the other. It's about 1/2" difference. You can't use the washer on R\F side. Here's the pics of each side. To Me the L/F looks correct with having more threads showing and sitting lower on the spindle. Brothers did warrenty me a new spindle (arrived today) but seems to be the same. I was curious if anyone else has had same problem??
__________________
64 C10 Stepside 350/4psd Driver/Project on air. Dom bags, Dual Viair and AccuAir 08 Ford F150 Limited- F-word ! Daily Driver .......................____ ..........._______l/  \____...........|_/(0)\_ll____/(0)_l. |
|
|
|
02-25-2014, 07:09 PM
|
#2 |
|
Registered User
Join Date: Sep 2009
Location: California Delta
Posts: 2,163
|
Re: Spindle Problem
Look to me like the left one is the problem. The cotter pin is way above the castle nut. Which spindle did they replace?
__________________
Name: Rich Current Ride: 1964 C-10 Short Fleetside Daily Driver: 2005 GMC crew cab short fleetside /2001 Chevy Tahoe Past GM Trucks: 1959 GMC short stepside 1968 GMC short stepside-4x4 1973 Chevy short stepside 1989 Chevy short fleetside-reg cab 1993 Chevy short fleetside-Xcab 2002 Chevy short fleetside-Xcab Save the dinosaurs, use synthetic oil. |
|
|
|
|
02-25-2014, 07:14 PM
|
#3 |
|
Registered User
Join Date: Feb 2013
Location: Sapulpa Oklahoma
Posts: 197
|
Re: Spindle Problem
I just installed CPP drop spindles last week and they both fit like the top photo . Dust shield just barely touching the bottom A arm. Is there a difference in your ball joints ?
|
|
|
|
|
02-25-2014, 09:31 PM
|
#4 |
|
Registered User
Join Date: Oct 2012
Location: Greely, On, Canada
Posts: 89
|
Re: Spindle Problem
They replaced the R/F. The ball joints are new 73-87 BJ. they are the same. Here's another pic of spindle. I asked if they could compare with known good spindles but I don't know if they did. Here's two other pics. I took these for guy @brothers.. anted to show using my finger difference.. I think one bore was machined wrong.
__________________
64 C10 Stepside 350/4psd Driver/Project on air. Dom bags, Dual Viair and AccuAir 08 Ford F150 Limited- F-word ! Daily Driver .......................____ ..........._______l/ \____...........|_/(0)\_ll____/(0)_l. |
|
|
|
|
02-25-2014, 10:01 PM
|
#5 |
|
Registered User
Join Date: Feb 2013
Location: Sapulpa Oklahoma
Posts: 197
|
Re: Spindle Problem
Or is one of your index fingers is bigger than the other LOL . Is it a tapered hole or can you drill out and fix. As expensive as they are they better send you another one. My drop spindles were for the stock 66 ball joints.
Last edited by firemanjimtfd; 02-25-2014 at 10:07 PM. |
|
|
|
|
02-26-2014, 02:43 AM
|
#6 | |
|
60-66 Nut
  Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,246
|
Re: Spindle Problem
I agree
I would say that the left spindle, lower hole was reamed too deep. Quote:
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
|
|
|
|
|
02-26-2014, 07:49 AM
|
#7 |
|
Registered User
Join Date: Oct 2010
Location: Independence,KS
Posts: 1,477
|
Re: Spindle Problem
I agree - the Left side is the concern. The cotter pin should go thru the castellated part of the nut, not that far above it.
I'd send CPP those pics and they should see the problem, too. |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
