FL FS: project left overs, gauges, shifter, engine, trans - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jamis · 05-12-2010, 12:22 PM

This is whats left of my project, thanks to all of you guys that bought the rest of the project. It was a pleasure meeting you guys

Hurst Promatic 2 shifter $150 shipped SOLD
Dolphin 6 gauge set mechanical speedo. The panel is just a mock up. You get the gauges, sending units and new speedo cable. $150 shipped SOLD

Vortec 350 everything on this engine is new but the block, crank and rods. Has about 2 hours of run time. If your interested I will give you the details $2500 no shipping

Holley Nascar 390 cfm, fuel line not included $250 shipped
http://www.holley.com/0-80507-1.asp

Rebuilt Turbo 400 long tail shaft, includes stock converter and B&M 3500 stall, trans cooler and new single piece drive shaft. This set up will fit a lowered SWB truck $800 no shipping

New fleet side, rear bed sill for steel floor $80 shipped

*ksjh1316* · 05-12-2010, 06:51 PM

What is the sizes on the gauges?

jamis · 05-12-2010, 07:16 PM

2 1/8 and 3 3/8

**leddzepp** · 05-12-2010, 08:21 PM

Great price on that Holley 390

gr8one · 05-12-2010, 08:42 PM

where are you located in florida?

jamis · 05-12-2010, 08:47 PM

Quote:

Originally Posted by leddzepp

Great price on that Holley 390

The pricing on those carb is out of control, I just dont have a use for it anymore and rather see it put to use then sitting on my shelf. I will also throw in a dozen or so diffrent size air bleeds for it and what ever other spare parts I may have. I think I may have some extra throttle blades and floats for it as well I cant remember

jamis · 05-12-2010, 08:48 PM

Quote:

Originally Posted by gr8one

where are you located in florida?

Naples

**BIG ORANGE** · 05-12-2010, 09:07 PM

Interested in single piece drivershaft, how long is it from center of joint to joint???? 29270

jamis · 05-13-2010, 08:30 AM

The drive shaft is 51 1/2 CTC but I dont have any idea what it would cost to ship something like that. The price for the shaft is $200 plus what ever the cost of shipping will be

68chevyfuelie · 05-13-2010, 09:23 AM

"Dolphin 6 gauge set mechanical speedo. The panel is just a mock up. You get the gauges, sending units and new speedo cable. $150 shipped" (Quote)

Is just the panel for sale? The way I read it, is that it's seperate. If it's not, did you buy it somewhere or make it? Thanks.

jamis · 05-13-2010, 09:35 AM

Quote:

Originally Posted by 68chevyfuelie

Is just the panel for sale? The way I read it, is that it's seperate. If it's not, did you buy it somewhere or make it? Thanks.

That panel you see is junk, I made it from a piece of scrap aluminum just so I could have gauges and do the wiring while I drove the project around.

68chevyfuelie · 05-13-2010, 09:44 AM

I understand that, but that's all I want, is a piece of aluminum to hold oil/water/tach gauges. I started to make one, but it's a pain in the butt. I'd still be interested in buying it if you change your mind. Thanks.

POPO1984 · 05-13-2010, 09:51 AM

will these guages fit the factory holes of a 72 c10 guage panel. what ohm rating is the fuel guage

**BIG ORANGE** · 05-13-2010, 10:04 AM

Quote:

Originally Posted by jamis

The drive shaft is 51 1/2 CTC but I dont have any idea what it would cost to ship something like that. The price for the shaft is $200 plus what ever the cost of shipping will be

Thanks but way to short,,,,

jamis · 05-13-2010, 10:28 AM

Quote:

Originally Posted by 68chevyfuelie

I understand that, but that's all I want, is a piece of aluminum to hold oil/water/tach gauges. I started to make one, but it's a pain in the butt. I'd still be interested in buying it if you change your mind. Thanks.

If it will help you out, you can have it just pay for the shipping.

jamis · 05-13-2010, 10:29 AM

Quote:

Originally Posted by BIG ORANGE

Thanks but way to short,,,,

funny...thats what the wife always says

jamis · 05-13-2010, 10:32 AM

Quote:

Originally Posted by POPO1984

will these guages fit the factory holes of a 72 c10 guage panel. what ohm rating is the fuel guage

Won’t fit with out some serious and hideous grinding. I can’t remember but it comes with its own fuel sending unit for use in a fuel cell.

68chevyfuelie · 05-13-2010, 06:34 PM

Let me know how much to ship to Ontario N2H 5H1, and PM me payment details. Thanks.

jmedero · 05-13-2010, 11:36 PM

Guage still available? If so let me know.
Thanks

jamis · 05-14-2010, 07:15 AM

Quote:

Originally Posted by jmedero

Guage still available? If so let me know.
Thanks

yes

POPO1984 · 05-14-2010, 09:19 AM

Thanks ill pass

Fesser · 05-14-2010, 12:05 PM

I'll take the guages if the guys in front of me don't.

Fesser · 05-14-2010, 12:06 PM

meant gauges, not guages

STINEY · 05-14-2010, 12:48 PM

Can you do $100 on the shifter? If so I'll take it today.

jmedero · 05-14-2010, 01:49 PM

I'll pass on guages. Thanks

05-12-2010, 12:22 PM	#1
jamis F.A.S.T. president Join Date: Sep 2003 Location: Florida Posts: 1,883	FS: project left overs, gauges, shifter, engine, trans This is whats left of my project, thanks to all of you guys that bought the rest of the project. It was a pleasure meeting you guys Hurst Promatic 2 shifter $150 shipped SOLD Dolphin 6 gauge set mechanical speedo. The panel is just a mock up. You get the gauges, sending units and new speedo cable. $150 shipped SOLD Vortec 350 everything on this engine is new but the block, crank and rods. Has about 2 hours of run time. If your interested I will give you the details $2500 no shipping Holley Nascar 390 cfm, fuel line not included $250 shipped http://www.holley.com/0-80507-1.asp Rebuilt Turbo 400 long tail shaft, includes stock converter and B&M 3500 stall, trans cooler and new single piece drive shaft. This set up will fit a lowered SWB truck $800 no shipping New fleet side, rear bed sill for steel floor $80 shipped __________________ F.A.S.T. President and Founder Fabricators for the Advancement of Sawsall Technology "A fear of the Sawsall is a sign of retarded sexual and emotional maturity." ~Sigmund Freud, "General Introduction to Psychoanalysis" Last edited by jamis; 06-12-2010 at 06:52 AM.

05-12-2010, 06:51 PM	#2
ksjh1316 Account Suspended Join Date: Jul 2007 Location: Wichita KS Posts: 1,599	Re: FS: project left overs, gauges, shifter, engine, trans What is the sizes on the gauges?

05-12-2010, 07:16 PM	#3
jamis F.A.S.T. president Join Date: Sep 2003 Location: Florida Posts: 1,883	Re: FS: project left overs, gauges, shifter, engine, trans 2 1/8 and 3 3/8 __________________ F.A.S.T. President and Founder Fabricators for the Advancement of Sawsall Technology "A fear of the Sawsall is a sign of retarded sexual and emotional maturity." ~Sigmund Freud, "General Introduction to Psychoanalysis"

05-12-2010, 08:21 PM	#4
leddzepp Moderator Join Date: May 2007 Location: Southern Cal Posts: 19,995	Re: FS: project left overs, gauges, shifter, engine, trans Great price on that Holley 390 __________________ 1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed. 1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck. RIP ElJay RIP 67ChevyRedneck RIP Grumpy Old Man

05-12-2010, 08:42 PM	#5
gr8one Registered User Join Date: Nov 2004 Location: Fort Meade Fl Posts: 184	Re: FS: project left overs, gauges, shifter, engine, trans where are you located in florida?

05-12-2010, 09:07 PM	#8
BIG ORANGE Senior Member Join Date: Oct 2001 Location: Lancaster S.C. Posts: 4,752	Re: FS: project left overs, gauges, shifter, engine, trans Interested in single piece drivershaft, how long is it from center of joint to joint???? 29270 __________________ Things happen for a reason!

05-13-2010, 08:30 AM	#9
jamis F.A.S.T. president Join Date: Sep 2003 Location: Florida Posts: 1,883	Re: FS: project left overs, gauges, shifter, engine, trans The drive shaft is 51 1/2 CTC but I dont have any idea what it would cost to ship something like that. The price for the shaft is $200 plus what ever the cost of shipping will be __________________ F.A.S.T. President and Founder Fabricators for the Advancement of Sawsall Technology "A fear of the Sawsall is a sign of retarded sexual and emotional maturity." ~Sigmund Freud, "General Introduction to Psychoanalysis"

05-13-2010, 09:23 AM	#10
68chevyfuelie Registered User Join Date: Mar 2008 Location: Kitchener, Ontario Posts: 487	Re: FS: project left overs, gauges, shifter, engine, trans "Dolphin 6 gauge set mechanical speedo. The panel is just a mock up. You get the gauges, sending units and new speedo cable. $150 shipped" (Quote) Is just the panel for sale? The way I read it, is that it's seperate. If it's not, did you buy it somewhere or make it? Thanks.

05-13-2010, 09:44 AM	#12
68chevyfuelie Registered User Join Date: Mar 2008 Location: Kitchener, Ontario Posts: 487	Re: FS: project left overs, gauges, shifter, engine, trans I understand that, but that's all I want, is a piece of aluminum to hold oil/water/tach gauges. I started to make one, but it's a pain in the butt. I'd still be interested in buying it if you change your mind. Thanks.

05-13-2010, 09:51 AM	#13
POPO1984 Registered User Join Date: Jul 2009 Location: Houston, Tx Posts: 1,133	Re: FS: project left overs, gauges, shifter, engine, trans will these guages fit the factory holes of a 72 c10 guage panel. what ohm rating is the fuel guage __________________ 1972 SWB Medium Olive South Houston Instagram: Antbish84

05-13-2010, 06:34 PM	#18
68chevyfuelie Registered User Join Date: Mar 2008 Location: Kitchener, Ontario Posts: 487	Re: FS: project left overs, gauges, shifter, engine, trans Let me know how much to ship to Ontario N2H 5H1, and PM me payment details. Thanks.

05-13-2010, 11:36 PM	#19
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,072	Re: FS: project left overs, gauges, shifter, engine, trans Guage still available? If so let me know. Thanks __________________ 68 BB burb build thread Scott's super slam front/rear http://67-72chevytrucks.com/vboard/s...d.php?t=378084

05-14-2010, 09:19 AM	#21
POPO1984 Registered User Join Date: Jul 2009 Location: Houston, Tx Posts: 1,133	Re: FS: project left overs, gauges, shifter, engine, trans Thanks ill pass __________________ 1972 SWB Medium Olive South Houston Instagram: Antbish84

05-14-2010, 12:05 PM	#22
Fesser Registered User Join Date: Feb 2010 Location: Napa, CA Posts: 519	Re: FS: project left overs, gauges, shifter, engine, trans I'll take the guages if the guys in front of me don't.

05-14-2010, 12:06 PM	#23
Fesser Registered User Join Date: Feb 2010 Location: Napa, CA Posts: 519	Re: FS: project left overs, gauges, shifter, engine, trans meant gauges, not guages



Register or Log In To remove these advertisements.

05-14-2010, 12:48 PM	#24
STINEY Registered User Join Date: May 2008 Location: Bucyrus Ohio Posts: 32	Re: FS: project left overs, gauges, shifter, engine, trans Can you do $100 on the shifter? If so I'll take it today. __________________ Bucyrus, Ohio https://i.imgur.com/TeUPWqt.jpg

05-14-2010, 01:49 PM	#25
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,072	Re: FS: project left overs, gauges, shifter, engine, trans I'll pass on guages. Thanks __________________ 68 BB burb build thread Scott's super slam front/rear http://67-72chevytrucks.com/vboard/s...d.php?t=378084

Register or Log In To remove these advertisements.