The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board > Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-06-2012, 01:55 PM   #1
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
58 TRUK intro

before reading my thread or any thread that uses photosucket picture hosting...
view this thread with google chrome web browser and add the photosucket hotlink extension to chrome

-----------------------------------------------------------------------------------
new guy intro to this site. i've been working on my 58 for 8 yrs, though i've owned this one for ~25 yrs.
back then it was my daily driver/work truck for my own electrical business.
bought my 1st 58 from the high school janitor back in 72.
had various 56-59 trucks since, all were dd's.

this is around 2000.


truk came from arkansas, i thought it was a good body; until i had it sand blasted.
found out it was a rusty cab, wrecked sometime in the 70s with decent front clip.
replaced floors, rockers, steps, cab corners, hinge pockets and door bottoms in & out.

58 truk had a ladder rack bolted to the cowl and the bed at one time.
the wreck that replaced the front clip also wiped out the whole left side.
a full inch of filler covered this lr fender and reshaped the lip.

Last edited by _Ogre; 01-30-2018 at 02:52 PM.
_Ogre is offline   Reply With Quote
Old 01-06-2012, 01:59 PM   #2
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: 58 TRUK intro

the battery has been relocated behind the pass seat.
welded up 100+ holes in the firewall.
shaved cowl vent and shaved cowl seam.



_Ogre is offline   Reply With Quote
Old 01-06-2012, 02:09 PM   #3
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
frame

fully boxed frame, 'fatman fab' mustII x-member, 86 trans am rearend w/ 3.27 posi gear,
axle flipped on top of stock springs, c-notched frame, 4 wheel disc brakes, ss brake lines
and 03 cobra hydroboost in stock mc location.





_Ogre is offline   Reply With Quote
Old 01-06-2012, 02:18 PM   #4
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
bed

for reasons i cannot explain...

frame and bed shortened 6'', 90 new yorker trunk (8'' sectioned) installed.





fiberglass tonneau cover





trex plastic bed ''wood''

_Ogre is offline   Reply With Quote
Old 01-06-2012, 02:25 PM   #5
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
drive train

ramjet 350: 350 hp, 400 ftlb, efi, gm crate motor
700r4 trans, 86 trans am rearend w/ 3.27 posi.
22 gal al fuel tank side fill with new yorker gas door.





_Ogre is offline   Reply With Quote
Old 01-06-2012, 02:30 PM   #6
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: 58 TRUK intro

as it is now.







_Ogre is offline   Reply With Quote
Old 01-06-2012, 02:43 PM   #7
hopped up
Registered User
 
hopped up's Avatar
 
Join Date: Jul 2010
Location: los angeles,ca
Posts: 3,617
Re: 58 TRUK intro

I like it , nice truck!!
Posted via Mobile Device
hopped up is offline   Reply With Quote
Old 01-06-2012, 02:55 PM   #8
Red Foreman
Registered User
 
Red Foreman's Avatar
 
Join Date: Dec 2009
Location: Melbourne Australia
Posts: 549
Re: 58 TRUK intro

Very Cool Ogre, I like its stance & quick little build thread to boot!
Red Foreman is offline   Reply With Quote
Old 01-06-2012, 03:00 PM   #9
meter swinger
Registered User
 
meter swinger's Avatar
 
Join Date: Apr 2009
Location: Kennewick WA.
Posts: 1,437
Re: 58 TRUK intro

Awesome! Great looking truck man. Thanks for the pics, and welcome to the board.
Posted via Mobile Device
meter swinger is offline   Reply With Quote
Old 01-06-2012, 04:05 PM   #10
OrrieG
Registered User
 
OrrieG's Avatar
 
Join Date: Jun 2006
Location: Idaho
Posts: 8,800
Re: bed

Quote:
Originally Posted by _Ogre View Post
for reasons i cannot explain...

frame and bed shortened 6'', 90 new yorker trunk (8'' sectioned) installed.
I have seen that once before. If you are not going to be hauling stuff like lumber and plywood or motorcycles is sort of makes sense. I like it.
__________________
1959 Chevy Short Fleetside w/ 74 4WD drive train (current project) OrrieG Build Thread
1964 Chevelle Malibu w/ 355-350TH (daily driver)
Helpful AD and TF Manual Site Old Car Manual Project
OrrieG is offline   Reply With Quote
Old 01-06-2012, 07:05 PM   #11
Kim57
Registered User
 
Kim57's Avatar
 
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
Re: 58 TRUK intro

Welcome
Very nice truck.
I like the custom bed.
Kim
__________________
My build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=283107
Kim57 is offline   Reply With Quote
Old 01-06-2012, 10:07 PM   #12
vwjohnny
Registered User
 
vwjohnny's Avatar
 
Join Date: Dec 2008
Location: Tucson, AZ
Posts: 52
Re: 58 TRUK intro

Yellow... Really cool.
vwjohnny is offline   Reply With Quote
Old 01-06-2012, 10:27 PM   #13
Flames97
Registered User
 
Flames97's Avatar
 
Join Date: Jan 2010
Location: Tonasket, Washington
Posts: 316
Re: 58 TRUK intro

I just saw your truck on another website yesterday. Welcome and very nice truck.
__________________
-Aaron

'15.5 Chevy Duramax LTZ/Z71, LML, CC/SB
'77 Chevy K10, 4" lift, 33-12.50, 350/350
'55 Chevy Short Box (In Pieces)MII,4-link,Bagged,383 Stroker,700r4,3.73posi (SOLD)
My 55.2 Chevy 3100 Build
Flames97 is offline   Reply With Quote
Old 01-06-2012, 11:08 PM   #14
poncho_villa
Registered User
 
poncho_villa's Avatar
 
Join Date: Feb 2005
Location: B.C.
Posts: 457
Re: 58 TRUK intro

Totally Sweet!!
__________________
58 Apache short fleetside ona 64 chassis:
poncho_villa is offline   Reply With Quote
Old 01-07-2012, 12:11 AM   #15
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: 58 TRUK intro

thanks for the kudos, glad you like it.

these seats were freebies out of an 07 ford fusion, that was used for factory testing.
the covers were shot, but the frames and cushions were good.
with the head rest off, they were way to tall, sticking 8'' above the rear window.



i cut and welded the frames and cushions to match the tape line above and had a friend recover them.



the drivers seat is all electric, i welded up a base to raise the seats 2'' to give me a little more leg room.

_Ogre is offline   Reply With Quote
Old 01-07-2012, 12:28 AM   #16
Kim57
Registered User
 
Kim57's Avatar
 
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
Re: 58 TRUK intro

Those came out nice.
Kim
__________________
My build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=283107
Kim57 is offline   Reply With Quote
Old 01-07-2012, 12:29 AM   #17
mknittle
Registered User
 
mknittle's Avatar
 
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
Re: 58 TRUK intro

Nice work,And the bed looks great, nice metal work!
__________________
Mark

My GMC build.
http://67-72chevytrucks.com/vboard/s...d.php?t=536602
mknittle is offline   Reply With Quote
Old 01-07-2012, 12:44 AM   #18
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
58 TRUK interior

my interior was basic ugly butt truck w/ butcher dash.
i found a gmc safari minivan steering column to get tilt, ignition, turn and dimmer on the column.



the interior design started out fairly basic, a 4'' bent metal fascia to mount the radio and ac vents in.

but...
after doing all the custom work to the truk and bed, i found fiberglassforums.com and the interior snowballed from there.
i probably spent a year building this interior...

sub enclosure and armrest:









console: a few wires, single din dvd player, headrest monitor and a few switches for doors and windows.









then i needed to cover up the ugly steering column, hide the vintage air unit and some ac vents.
a little cardboard mailing tube, plywood and a hot glue gun, followed by fiberglass and little sanding.






Last edited by _Ogre; 01-07-2012 at 12:57 AM.
_Ogre is offline   Reply With Quote
Old 01-07-2012, 12:56 AM   #19
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
58 TRUK interior

kick panel speakers: i had shaved the cowl vent, thus had no use for kick panel vents.
4.5'' midrange and a 2'' tweeter.







add a little vinyl





2 rolls of rammatt, 20 yds of deadening foam and some carpet...



_Ogre is offline   Reply With Quote
Old 01-07-2012, 01:11 AM   #20
mknittle
Registered User
 
mknittle's Avatar
 
Join Date: Jul 2011
Location: Auburn ca.
Posts: 2,886
Re: 58 TRUK intro

nice fiberglass work I like the steering column cover,Looks better than a lot of the modesty panels I have seen. Keep up the good work!
__________________
Mark

My GMC build.
http://67-72chevytrucks.com/vboard/s...d.php?t=536602
mknittle is offline   Reply With Quote
Old 01-07-2012, 11:46 AM   #21
Kim57
Registered User
 
Kim57's Avatar
 
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
Re: 58 TRUK intro

Great job on the interior.
Kim
__________________
My build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=283107
Kim57 is offline   Reply With Quote
Old 01-07-2012, 03:55 PM   #22
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
58 TRUK doors

doors:

i wanted power windows without spending a lot of money.
a friend gave me a set of new (in 06) dodge durango power scissor regulators.
it took a bit of figuring before i cut the door and cut i did, a big ol hole.
i mocked up the regulator on a piece of wood to figure out where to mount and the travel required.
i ended up mounting the regulator on the door panel, all the access holes are for reaching screws.

mock up down


mock up up with door panel mount


door cut out


door assembled


i have shaved door handles. problem with a task force truck is the door glass is very close to the inner door skin. this makes positioning the solenoid difficult. i looked at placing it down low on the door and decided to make it easy by locating the solenoid on the outside of the door. i used new original style door latches.



then i started on door panels by cutting some 1/4'' luan plywood


make a frame work to fiberglass to


and some fiberglass, a smucking of filler and a lot of sanding...


add a little vinyl


some carpet, speakers and an armrest pad


some wheres in the middle of all this, i looked at rebuild my vent windows.
the wings and frames were rusty, it would have been $800 to replace the frames.
brothers one-piece-windows kit was on sale for $189, so i change to one-piece windows.
_Ogre is offline   Reply With Quote
Old 01-07-2012, 04:40 PM   #23
Kim57
Registered User
 
Kim57's Avatar
 
Join Date: Aug 2007
Location: Corona, California
Posts: 7,998
Re: 58 TRUK intro

Very ingenious on the power windows.
Kim
__________________
My build thread
http://67-72chevytrucks.com/vboard/s...d.php?t=283107
Kim57 is offline   Reply With Quote
Old 01-07-2012, 05:12 PM   #24
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
Re: 58 TRUK intro

Quote:
Originally Posted by Kim57 View Post
Very ingenious on the power windows.
Kim
necessity is the mother of invention
_Ogre is offline   Reply With Quote
Old 01-08-2012, 01:16 PM   #25
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,680
TRUK doors 2.0

running wires into the door from the door jam proved to be a challenge.
i had 2 speaker wire, 2 solenoid wires, 2 window wires and a safety door release cable to run into the door.
the release cable is a bicycle brake cable ~3/16'', needless to say i had a fistful to run into the doors.
i tried the spring like door wire loom; it wouldn't carry half the wires and wouldn't work with the door hinge geometry on 55-59 trucks.

again, necessity is the mother of invention...
i drew up the hinge geometry to design my door wire loom, just basic pivot points and door locations.


using 3/4'' sq aluminum tubing and some 1/4x2 flat stock from home depot, i made these.
pivot is a 1/8'' roll pin.


door open


door closing


they worked out rather well.
2-#16, 4-#14 and the 3/16'' cable fit in with room to spare.
everything mounts and pivots on the door jamb.
i cut an over sized hole in the door and made a plastic bushing to guide the loose end in and out of the door.
__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:03 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com