The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Info Center > FAQ Truck Tech

Web 67-72chevytrucks.com


 
 
Thread Tools Display Modes
Old 01-02-2014, 11:40 PM   #1
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Project remove my sunroof

Well, ever since I bought my truck in 1995 I've hated the sunroof in it. It never seemed to fit this type of truck (or any trucks for that matter). So I've decided to put my welding and fabrication skills to work and finally remove it once and for all! So here we go.....
Attached Images
  
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-02-2014, 11:42 PM   #2
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

First item on the list was getting a donor top, which I was able to acquire from a local board member (thanks again Bob). I removed it by drilling out each of the spot welds around the edge and cutting the back section of the cab to expose the spot-welds along the back.
Attached Images
 
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-02-2014, 11:45 PM   #3
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

the next step was to get my roof ready, so I used a wire brush attached to my 90 degree die grinder and polished away. This seemed to work the best to expose the spot welds.
Attached Images
  
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-02-2014, 11:53 PM   #4
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

Using a spot weld drill bit and some good ole elbow grease I was able to remove the top section.
Attached Images
 
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-02-2014, 11:58 PM   #5
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

Tonight I decided to cut and weld in the lower roof section. This was no easy task, as warp and mismatch are possible at this point. I just took my time and match everything up and spot welded until the cows came home...
Attached Images
   
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-03-2014, 12:20 AM   #6
Mike's money pit
Registered User
 
Join Date: Nov 2012
Location: Atlanta
Posts: 553
Re: Project remove my sunroof

Looks great! I will be watching with interest because I have some rust to replace in my roof.
Mike
Mike's money pit is offline  
Old 01-03-2014, 12:40 AM   #7
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

Thanks Mike. Yeah, this is a unique opportunity to clean up the rust and paint this section.
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-03-2014, 12:53 AM   #8
Leroy-B1
Registered User
 
Join Date: Dec 2010
Location: Mars Hill, NC
Posts: 1,994
Re: Project remove my sunroof

Good info I've never saw it done this way...I've saw the post cut and a complete top install...thanks for this
Leroy-B1 is offline  
Old 01-03-2014, 01:19 AM   #9
Terry Crist
Registered User
 
Join Date: Aug 2013
Location: Manteca, California
Posts: 59
Re: Project remove my sunroof

Have you ever tried these, http://www.eastwood.com/intergrip-pa...-set-of-4.html. to help keep everything flush.
Terry Crist is offline  
Old 01-03-2014, 01:21 AM   #10
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

I've never used them before, but I should pick up some and try them out. One of the biggest issue I had was with the "crown" of the roof, as its not flat.
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-03-2014, 01:45 AM   #11
swamp rat
Registered User
 
swamp rat's Avatar
 
Join Date: Oct 2007
Location: Spanaway
Posts: 8,451
Re: Project remove my sunroof

Quote:
Originally Posted by Terry Crist View Post
Have you ever tried these, http://www.eastwood.com/intergrip-pa...-set-of-4.html. to help keep everything flush.
Harbor freight has them a lot cheaper... are they worse or better i don't know but i have a set and they seem ok.
__________________
Mike.

Swamp Rat build thread :
http://67-72chevytrucks.com/vboard/s...d.php?t=595019

72 3/4T 4X4
4" BDS Lift
33" BFG's
swamp rat is offline  
Old 01-03-2014, 11:27 AM   #12
alsriv2
Registered User
 
alsriv2's Avatar
 
Join Date: Sep 2010
Location: Formerly MD and San Diego, now loving life in Arizona
Posts: 1,636
Re: Project remove my sunroof

Subscribed!

I have to replace my roof top due to previously done poor repair job. I will watch how you are getting this done, but am curious about the rear spot welds along that seam.
__________________
Alan

2012 Ram 3500 Dually Crew Cab 6.7 Cummins
2014 Palomino Columbus 340RK 5th wheel
'69 Chevy C10 396BB
alsriv2 is offline  
Old 01-03-2014, 08:25 PM   #13
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

I've pondered this idea for some time and I believe the best approach is to use 3M automotive panel adhesive. I'll have to either tack weld a few areas along the seam to keep it in place while it cures, or figure out a way to "clamp" the panel so it has the proper force to keep it in place.
()
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-03-2014, 08:46 PM   #14
hugger6933
Registered User
 
Join Date: Oct 2008
Location: Marianna Arkansas
Posts: 7,279
Re: Project remove my sunroof

This time of year is the wrong time to think about using the panel bonding stuff. It needs to be pretty warm to work well I learned that the hard way putting a roof on a 04 C2500. With all the guts out [int.] the welder is still the best way to go. I had one of my body guys use some of the 3M bonding stuff on his bed skins on his truck [i was letting him build at my shop on the weekend on his time] it failed soon as we lifted the bed to place it on the truck. I can't atest to his proper use of the product , but I do know I used it right with the exception it got cold the night I used it and it failed. The work progress is looking real good, there is a new skin out now for those needing to do this and not able to find a donor. I have done this many times using used panels and it does make the labor twice as much and at some point you may have to consider the amount of labor, but I always figure mine is cheap. Jim
hugger6933 is offline  
Old 01-03-2014, 08:51 PM   #15
BugzC10
Registered User
 
BugzC10's Avatar
 
Join Date: Oct 2012
Location: Rose Hill Kansas
Posts: 1,351
Re: Project remove my sunroof

Looks like your outer skin would be a good candidate for the 3M Panel Bonding, but like you said the clamping in place could be an issue. Maybe weld temporary brackets on each side of the seam around the back and back corners to give you a clamping points. You should be able to use C clamps in the front and the sides. I'm no expert...just an observation.
__________________
1970 C10 Short Stepper with 71/72 front clip.
BugzC10 is offline  
Old 01-03-2014, 08:51 PM   #16
hamjet
Registered User
 
hamjet's Avatar
 
Join Date: Apr 2013
Location: South Westerlo, New York
Posts: 1,325
Re: Project remove my sunroof

I used a product by Lord Corp. called Fusor for applying rockers and cab corners on a 1990 pickup 6 years ago. its still holding, but I used pop rivets to hold it till it cured then ground them off....
__________________
Thanks, Joe..
1969 C/10, 348 C.I., 3X2 bbl. V8, 2004r , LWB.
hamjet is offline  
Old 01-03-2014, 09:18 PM   #17
Razor454
Registered User
 
Razor454's Avatar
 
Join Date: Feb 2004
Location: Stokesdale, North Carolina
Posts: 341
Re: Project remove my sunroof

hugger6933, I agree with you on the temperature. I'm kind of at a stopping point until the temp increases, as I also need to paint the inside with an expoxy paint. Also, I know that this stuff will work, but I need to make sure I have four things correct: Temperature, pressure, cure time and bond gap. If I miss anyone of these items my bond will prematurely fail.
__________________
1967 SwB, 454 BB, 4L80E trans, 3.73 eaton posi

1997 C2500 Ext Cab 5.7 Liter

1955 3/4 ton 1st series w/ 235 straight six Sold it
Razor454 is offline  
Old 01-03-2014, 10:46 PM   #18
black_sheep454
Registered User
 
Join Date: May 2011
Location: Lebanon, Mo.
Posts: 1,315
Re: Project remove my sunroof

3m panel bond is some very strong stuff. I've glued a ton of bedsides and roof skins on with it. Just make sure it's prepped well and you'll have no problems.
__________________
1968 chevy lwb, getting ready to join forces with the 70 gmc
1970 gmc swb, getting ready to be a 68 chevy swb
1971 gmc lwb 2500 2wd Sierra Grande
1988 chevy 1-ton crew cab 2wd waiting for a 12v cummins
black_sheep454 is offline  
Old 01-03-2014, 11:16 PM   #19
chipflyer
Registered User
 
chipflyer's Avatar
 
Join Date: May 2004
Location: Topeka, Ks
Posts: 2,293
Re: Project remove my sunroof

I plan to replace my roof with one that has hockey puck style marker lamps and plan to do what you have done to remove the roof. The only way to put the roof on and make it look right along the back seam is to use panel bonding adhesive. The front and sides could be plug welded but there is no way to weld the back and have it look correct. I've had good luck with panel adhesive too, not a bit afraid to use it.

Take a look at this older thread, lots of great info.

Jeff
__________________
I'm not a pessimist, I'm just optimistic that bad things are going to happen.

1971 Cheyenne Super K10 - tilt, cruise, air, am/fm, tow hooks, factory buckets!
1986 Jeep J10 pickup, - 5.3L Vortec with 4L60e and NP241.
chipflyer is offline  
Old 01-03-2014, 11:56 PM   #20
Terry Crist
Registered User
 
Join Date: Aug 2013
Location: Manteca, California
Posts: 59
Re: Project remove my sunroof

Quote:
Originally Posted by swamp rat View Post
Harbor freight has them a lot cheaper... are they worse or better i don't know but i have a set and they seem ok.
Cool, I did not know they had them. I'll have to check them out.
Terry Crist is offline  
Old 01-04-2014, 12:47 AM   #21
SCHRUMGMC
Registered User
 
SCHRUMGMC's Avatar
 
Join Date: Dec 2012
Location: North Carolina
Posts: 4,989
Re: Project remove my sunroof

Thank God...I don't know why in the hell people put sun roofs in these things
__________________
1971 GMC Sierra
1959 GMC 100
SCHRUMGMC is offline  
Old 01-04-2014, 01:49 AM   #22
sduckworth13
Registered User
 
sduckworth13's Avatar
 
Join Date: Mar 2011
Location: Kansas City, Missouri
Posts: 3,541
Re: Project remove my sunroof

Cool Mark, glad to see you tackling the roof repair. I removed the inner and outer panels recently after I botched a antenna hole repair in the roof. Good luck on the repair.
Attached Images
 
__________________
Scott
sduckworth13 is offline  
Old 01-04-2014, 07:35 AM   #23
Elliot949
Registered User
 
Elliot949's Avatar
 
Join Date: Sep 2010
Location: Winfield, Ks.
Posts: 4,162
Re: Project remove my sunroof

Nice work man...
Elliot949 is offline  
Old 01-04-2014, 09:27 AM   #24
69SWB4X4
Registered User
 
69SWB4X4's Avatar
 
Join Date: Oct 2013
Location: Oklahoma
Posts: 54
Re: Project remove my sunroof

I am about to do the same repair on my truck. My thought was to flange the sunroof opening and cut a patch from my donor skin. Could also flange the patch if room is an issue.. On the inside I plan to use dyna mat in the old sunroof hole and add a headliner.. Thoughts??
69SWB4X4 is offline  
Old 01-04-2014, 09:46 AM   #25
67 chevelle
Registered User
 
67 chevelle's Avatar
 
Join Date: May 2013
Location: WEST PALM FLORIDA
Posts: 1,174
Re: Project remove my sunroof

3m panel bond is great stuff , I have never had a problem using it , for quarter panels and other things , I do live in Florida though , I use small self tapping sheet metal screws to hold it and then just fill them
__________________
68 Long Fleet , ly6 , turbo 350 , 3-5 drop , original paint , front discs
67 Small window , 7 foot bed , tweaked 6.0 LSX 2004R Medium Olive
58 Apache fleet , 235 , offy intake , dual exhaust , 4 on the floor , red/white
69 Long Fleet , Custom , 6.0, 4l60 , AC , Medium Olive
67 chevelle is offline  
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:38 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com