Lifting my truck - The 1947 - Present Chevrolet & GMC Truck Message Board Network

JAKES 68GMC · 03-06-2008, 01:52 AM

I want to put a 2" lift in my truck just to raise it up alittle...it feels low compared to the old one.

I was planning on putting 2" blocks in the back, but I dont know how to lift the front. Maybe cranking the torsion bars? Any help would be appreciated...because I have no clue how to lift the front. Thanks.

**special-K** · 03-06-2008, 05:44 AM

Rancho makes a torsion bar lift that`s not too expensive for 1500s.They may just be 2500HD/3500 parts,because they don`t make anything but the assembly-drop lifts for 8-luggers.On my 3500 I tweeked the t-bars for about another 2-3".I can run 285/75x16s.I run 255/85x16s now.

JAKES 68GMC · 03-06-2008, 06:20 AM

Tim, exactly how did you tweak the torsion bars? I have no clue when it comes to IFS stuff, I just want my truck to ride alittle higher.

Thanks for your help.

**special-K** · 03-06-2008, 06:35 AM

At the back end of the torsion bars there`s a huge hex head.You turn then=m upYou can go a ouple few inches and still have adequate travel(camber).If you don`t have a wrench,asee if a shop will do it.It won`t cost much at all and can be done in minutes.
Her`s my other truck,R.I.P.:

JAKES 68GMC · 03-06-2008, 06:46 AM

Oh ok, thats what I thought. I've heard of cranking torsion bars up before. So you think this will get me a couple more inches without hurting anything?

**Yukon Jack** · 03-06-2008, 08:49 AM

I adjusted my torsion bars to gain a bit of lift on my 95 GMC Yukon. Approximately 2 years later I had to replace the upper ball joints and had some wear on a couple steering components (can't remember exactly what was worn at this point). Can't swear this was caused from the torsion bars being adjusted but that is my suspicion.

Blue_71 · 03-06-2008, 10:45 AM

probably idler and pitman yukon, those suckers wear out quick!!

i think, if i remember right, the nut to adjust is an 18mm head

Wreckless_71 · 03-06-2008, 12:10 PM

My dad has a '05 duramax and cranked up the torsionbars then had it aligned again to adjust for the camber/caster, we've got a buddy with an alignment shop so it wasn't any big deal... it looks a lot better than stock anyways.

**special-K** · 03-06-2008, 04:02 PM

My GMC has 250,000mi. on it and I did this back in`92.The only thing I`ve ever had done to the front end is the idler arm every 80,000 or so.This is typical of all IFS GMs.My alignment never has been touched,either.The IFS is designed to maintain proper camber within it`s travel range.So,no probs there.

*gn4u2c2* · 03-06-2008, 09:10 PM

Tim !! When are you going to be home ?? I want to stop in and chat a few min if possible. maybe monday ?? thanks 443-398-7326

**special-K** · 03-07-2008, 01:27 AM

Sounds good #2.I`m home in the eves/nights.There`s a swap meet at Howard County Fairgrounds (I-70 & MD32,actually off of MD144 west of 32) on Saturday.I`m working in Westminster tommorrow & Fri.

JAKES 68GMC · 03-07-2008, 02:45 AM

Thanks for the help guys, appreciate it.

03-06-2008, 01:52 AM	#1
JAKES 68GMC Aluminum slot wheels rule... Join Date: Jan 2006 Location: Maine Posts: 6,212	Lifting my truck I want to put a 2" lift in my truck just to raise it up alittle...it feels low compared to the old one. I was planning on putting 2" blocks in the back, but I dont know how to lift the front. Maybe cranking the torsion bars? Any help would be appreciated...because I have no clue how to lift the front. Thanks.

03-06-2008, 06:20 AM	#3
JAKES 68GMC Aluminum slot wheels rule... Join Date: Jan 2006 Location: Maine Posts: 6,212	Re: Lifting my truck Tim, exactly how did you tweak the torsion bars? I have no clue when it comes to IFS stuff, I just want my truck to ride alittle higher. Thanks for your help.

03-06-2008, 06:35 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: Lifting my truck At the back end of the torsion bars there`s a huge hex head.You turn then=m upYou can go a ouple few inches and still have adequate travel(camber).If you don`t have a wrench,asee if a shop will do it.It won`t cost much at all and can be done in minutes. Her`s my other truck,R.I.P.: __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 03-06-2008 at 06:37 AM.

03-06-2008, 06:46 AM	#5
JAKES 68GMC Aluminum slot wheels rule... Join Date: Jan 2006 Location: Maine Posts: 6,212	Re: Lifting my truck Oh ok, thats what I thought. I've heard of cranking torsion bars up before. So you think this will get me a couple more inches without hurting anything?

03-06-2008, 08:49 AM	#6
Yukon Jack Post Whore Join Date: Feb 2000 Location: Rose Hill, KS, USA Posts: 12,683	Re: Lifting my truck I adjusted my torsion bars to gain a bit of lift on my 95 GMC Yukon. Approximately 2 years later I had to replace the upper ball joints and had some wear on a couple steering components (can't remember exactly what was worn at this point). Can't swear this was caused from the torsion bars being adjusted but that is my suspicion. __________________ 1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14

03-06-2008, 05:44 AM	#2
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: Lifting my truck Rancho makes a torsion bar lift that`s not too expensive for 1500s.They may just be 2500HD/3500 parts,because they don`t make anything but the assembly-drop lifts for 8-luggers.On my 3500 I tweeked the t-bars for about another 2-3".I can run 285/75x16s.I run 255/85x16s now. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

03-06-2008, 12:10 PM	#8
Wreckless_71 Registered User Join Date: Apr 2007 Location: Kelso, WA Posts: 363	Re: Lifting my truck My dad has a '05 duramax and cranked up the torsionbars then had it aligned again to adjust for the camber/caster, we've got a buddy with an alignment shop so it wasn't any big deal... it looks a lot better than stock anyways. __________________ 1972 K10 4" lift, 35’s, 383 stroker, 700r4, current project. 1971 C10 3"/5" static drop, 355/350. "La Bamba.” The current daily driver.

03-06-2008, 04:02 PM	#9
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: Lifting my truck My GMC has 250,000mi. on it and I did this back in`92.The only thing I`ve ever had done to the front end is the idler arm every 80,000 or so.This is typical of all IFS GMs.My alignment never has been touched,either.The IFS is designed to maintain proper camber within it`s travel range.So,no probs there. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

03-06-2008, 09:10 PM	#10
gn4u2c2 Account Suspended Join Date: Jul 2006 Location: d.c Posts: 315	Re: Lifting my truck Tim !! When are you going to be home ?? I want to stop in and chat a few min if possible. maybe monday ?? thanks 443-398-7326

03-07-2008, 01:27 AM	#11
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: Lifting my truck Sounds good #2.I`m home in the eves/nights.There`s a swap meet at Howard County Fairgrounds (I-70 & MD32,actually off of MD144 west of 32) on Saturday.I`m working in Westminster tommorrow & Fri. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

03-07-2008, 02:45 AM	#12
JAKES 68GMC Aluminum slot wheels rule... Join Date: Jan 2006 Location: Maine Posts: 6,212	Re: Lifting my truck Thanks for the help guys, appreciate it.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.