Pic Request - Blazer Skid Plate - The 1947 - Present Chevrolet & GMC Truck Message Board Network

LUV2XCLR8 · 07-05-2005, 05:04 PM

Hey guys, now that I own one of these things, where does it go, I know this sounds stupid, but a picture is
worth a thousand words, and please give them to me as detailed as possible, if they are to large to post you
can send them to luv2xclr8@charter.net, Thanks in advance 4 helping

(I included some pic's of it 4 ya

)

**hilljob26** · 07-05-2005, 08:07 PM

i dont have a pic,but i am pretty sure it goes behind the tranny x member,and the extended part of that piece w/ the 4 holes,bolts to the tranny x member,it should fit in there like a glove

LUV2XCLR8 · 07-05-2005, 08:38 PM

Quote:

Originally Posted by hilljob26

i dont have a pic,but i am pretty sure it goes behind the tranny x member,and the extended part of that piece w/ the 4 holes,bolts to the tranny x member,it should fit in there like a glove

Well, from what I can tell, there are no holes in my frame for that second
crossmember, not that it is a big deal to put holes in it, that is the mainly
the reason I asked, so I get the holes put in the right place for the install.

Livrat · 07-05-2005, 09:00 PM

here is a crappy pic I just took of the passengers side skid plate in my 68 GMC with a t350/205...sorry bout the blurr it just started to rain and I took it in a hurry..

vtblazer · 07-06-2005, 06:53 AM

Drivers side.

wingman · 07-06-2005, 07:34 AM

Ahh so that is what that piece is for, lucky i didnt throw it out last year when i couldnt figure out what the heck it was. Does anyone know if there is anything special about the second crossmember or is it the same as the first or what?

Burt4x4 · 07-06-2005, 02:32 PM

The second x-member is the same. You are missing the upper frame mounts. The piece you have only bolts to the lower part of the frame. THere are two other pices that bolt to the top of the frame then down to the x-member.
Hope this helps
Burt

LUV2XCLR8 · 07-06-2005, 03:45 PM

Thanks guys, so if I bolt up the plate to the front crossmember I already
have, I should just be able to line up the second member from that point
and create a few holes for it, right? Or is there more to it than that?

donkey69 · 07-06-2005, 10:58 PM

"git-r-done"!!!!

07-05-2005, 05:04 PM	#1
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,475	Pic Request - Blazer Skid Plate Hey guys, now that I own one of these things, where does it go, I know this sounds stupid, but a picture is worth a thousand words, and please give them to me as detailed as possible, if they are to large to post you can send them to luv2xclr8@charter.net, Thanks in advance 4 helping (I included some pic's of it 4 ya ) __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T Last edited by LUV2XCLR8; 10-23-2005 at 08:40 AM.

07-05-2005, 08:07 PM	#2
hilljob26 Registered User Join Date: Dec 2004 Location: Gypsum Kansas 67448 Posts: 1,681	i dont have a pic,but i am pretty sure it goes behind the tranny x member,and the extended part of that piece w/ the 4 holes,bolts to the tranny x member,it should fit in there like a glove __________________ 21 2500hd duramax 58 apache HILLJOB GRAPHIX--for all your graphic needs My build thread http://67-72chevytrucks.com/vboard/s...d.php?t=542497 LS ENGINE SWAP INFORMATION THREAD http://67-72chevytrucks.com/vboard/s...d.php?t=377348 4l60 to an NP205 http://67-72chevytrucks.com/vboard/s...43#post3697343

07-05-2005, 09:00 PM	#4
Livrat Member #1049 Join Date: Jun 2000 Location: Troy Montana Posts: 3,940	here is a crappy pic I just took of the passengers side skid plate in my 68 GMC with a t350/205...sorry bout the blurr it just started to rain and I took it in a hurry.. Attached Images Last edited by Livrat; 07-05-2005 at 09:03 PM.

07-06-2005, 06:53 AM	#5
vtblazer Registered User Join Date: Oct 2003 Location: Central Vermont Posts: 8,538	Drivers side. Attached Images

07-06-2005, 02:32 PM	#7
Burt4x4 Registered User Join Date: Feb 2000 Location: Modesto, CA Posts: 1,842	The second x-member is the same. You are missing the upper frame mounts. The piece you have only bolts to the lower part of the frame. THere are two other pices that bolt to the top of the frame then down to the x-member. Hope this helps Burt __________________ 1972 K5 MPFI454/Sm465/Np205/D60/14FFd/Re-Centerd H1s w/Swamper Iroks

07-06-2005, 07:34 AM	#6
wingman Registered User Join Date: Apr 2005 Posts: 41	Ahh so that is what that piece is for, lucky i didnt throw it out last year when i couldnt figure out what the heck it was. Does anyone know if there is anything special about the second crossmember or is it the same as the first or what?

07-06-2005, 03:45 PM	#8
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,475	Thanks guys, so if I bolt up the plate to the front crossmember I already have, I should just be able to line up the second member from that point and create a few holes for it, right? Or is there more to it than that? __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

07-06-2005, 10:58 PM	#9
donkey69 JB-80 &quot;Twice as Good&quot; Join Date: Jun 2004 Location: Central, MN Posts: 354	"git-r-done"!!!! __________________ HEY NOW!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.