The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-27-2015, 03:59 PM   #1
HallWood44
Registered User
 
Join Date: Mar 2015
Location: Marysville, CA
Posts: 3
1970, Straight 6, 3 on the Tree.

Starting a full restoration, I have removed the bed and started cleaning up the frame. Anyone have any recommendations for an engine rebuild kit or anything that can help me out as far as adding a little spice to the truck. I want to do mostly original with a few modern twists to it. Any help is greatly appreciated. I am currently stationed at JBLM, WA.
HallWood44 is offline   Reply With Quote
Old 03-27-2015, 05:36 PM   #2
GRX
Registered User
 
GRX's Avatar
 
Join Date: Jul 2010
Location: MD
Posts: 1,937
Re: 1970, Straight 6, 3 on the Tree.

First thing you want to do is find out if you have a 250 or a 292.

250 fuel pump is rearward of the motor mount

292 fuel pump is forward of the motor mount

Also, the 292 has a large coolant bypass hose to the water neck. 250 does not.
__________________
1969 c-10 Step Side Long Bed. I-6 250cid = = 1969 Pontiac GTO hard top. 400, 4-speed.
GRX is offline   Reply With Quote
Old 04-07-2015, 12:07 PM   #3
HallWood44
Registered User
 
Join Date: Mar 2015
Location: Marysville, CA
Posts: 3
Re: 1970, Straight 6, 3 on the Tree.

Its a 250. It runs solid just sounds a little rough. Also in 3rd gear it is screaming at 55. Any suggestions on an engine modifications or rebuilds and what to put in the rear end to add some speed. I want to keep it somewhat original but I am going to upgrade a few things.
HallWood44 is offline   Reply With Quote
Old 04-07-2015, 12:20 PM   #4
EARNHARDT#3
Registered User
 
EARNHARDT#3's Avatar
 
Join Date: May 2014
Location: PA
Posts: 1,417
Re: 1970, Straight 6, 3 on the Tree.

Quote:
Originally Posted by HallWood44 View Post
Its a 250. It runs solid just sounds a little rough. Also in 3rd gear it is screaming at 55. Any suggestions on an engine modifications or rebuilds and what to put in the rear end to add some speed. I want to keep it somewhat original but I am going to upgrade a few things.
I thought my 250 was screaming at 55 too. After I put a tach in my truck though I realized it was just a noisy old truck and it can cruise at 75-80mph no problem.
__________________
1967 C10, LWB, 250, Powerglide, PS, PB, 3/4 STATIC DROP
EARNHARDT#3 is offline   Reply With Quote
Old 04-07-2015, 12:15 PM   #5
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,712
Re: 1970, Straight 6, 3 on the Tree.

Quote:
Originally Posted by GRX View Post
First thing you want to do is find out if you have a 250 or a 292.

250 fuel pump is rearward of the motor mount

292 fuel pump is forward of the motor mount

Also, the 292 has a large coolant bypass hose to the water neck. 250 does not.
You got that fuel pump backwards!
Look again!
geezer#99 is online now   Reply With Quote
Old 04-07-2015, 12:33 PM   #6
GRX
Registered User
 
GRX's Avatar
 
Join Date: Jul 2010
Location: MD
Posts: 1,937
Quote:
Originally Posted by geezer#99 View Post
You got that fuel pump backwards!
Look again!
My bad. Thanks for the correction. That is what I get for typing before coffee.
__________________
1969 c-10 Step Side Long Bed. I-6 250cid = = 1969 Pontiac GTO hard top. 400, 4-speed.
GRX is offline   Reply With Quote
Old 04-07-2015, 02:38 PM   #7
Custom/Ten
Registered User
 
Custom/Ten's Avatar
 
Join Date: May 2014
Location: Mobile, AL
Posts: 422
Re: 1970, Straight 6, 3 on the Tree.

Hei distributor is a good mod for these 250's. I'm really happy with mine, bought one for an 80 250 and bolted right up didn't have to worry about tuning it for the right advance curve. FYI you need to remove the original resister wire and replace with a nice 12 g wire, none of that cheap parts store wire!
Custom/Ten is offline   Reply With Quote
Old 04-07-2015, 03:03 PM   #8
slomotion
Old Duffer
 
slomotion's Avatar
 
Join Date: Mar 2003
Location: Maine
Posts: 1,822
Re: 1970, Straight 6, 3 on the Tree.

You said in your original post that you were restoring your truck, but if you don't mind straying a little from original, the one thing I've really enjoyed is the T5 trans I put behind my six. At 65 MPH the engine is turning 2800 RPM. Much easier on my nerves going down the highway. You'd have to put in a floor shift, but it's all reversible if you wanted to go back original.
__________________
'68 Short C20 Flatbed Dually
w/ 292 4bbl, Langdon cast headers,
and WC T5 trans.

'81 G10 Shorty Van

"Good judgement comes from experience, and a lot of that comes from bad judgement." Will Rogers

"Under promise, then over achieve."
slomotion is offline   Reply With Quote
Old 04-07-2015, 06:03 PM   #9
HallWood44
Registered User
 
Join Date: Mar 2015
Location: Marysville, CA
Posts: 3
Re: 1970, Straight 6, 3 on the Tree.

I like the 3 on the tree, and with the previous replies I guess I have a 292. I've only helped people restore I e never taken one on myself. I just didn't know how much you could do to the engine to add a little power without changing the exterior
HallWood44 is offline   Reply With Quote
Old 04-07-2015, 06:52 PM   #10
slomotion
Old Duffer
 
slomotion's Avatar
 
Join Date: Mar 2003
Location: Maine
Posts: 1,822
Re: 1970, Straight 6, 3 on the Tree.

Quote:
Originally Posted by HallWood44 View Post
I like the 3 on the tree, and with the previous replies I guess I have a 292. I've only helped people restore I e never taken one on myself. I just didn't know how much you could do to the engine to add a little power without changing the exterior
About the only thing you can do without changing the exterior appearance is the HEI, but this is huge in performance and dependability.
If you don't want to change anything inside, there's headers, more/better carbs, and HEI.
The 292 is a great engine. Torquey, smooth, and almost bullet proof.
__________________
'68 Short C20 Flatbed Dually
w/ 292 4bbl, Langdon cast headers,
and WC T5 trans.

'81 G10 Shorty Van

"Good judgement comes from experience, and a lot of that comes from bad judgement." Will Rogers

"Under promise, then over achieve."
slomotion is offline   Reply With Quote
Old 04-07-2015, 09:52 PM   #11
GRX
Registered User
 
GRX's Avatar
 
Join Date: Jul 2010
Location: MD
Posts: 1,937
Re: 1970, Straight 6, 3 on the Tree.

Far as adding power, sky is the limit. All depends on how much money you have to spend and what you are willing to do to the engine. Bolt on parts like carb, headers, and ignition do little unless your internals are upgraded and can make good use of them. Changing to HEI does increase performance and reliability *if* you are using it to replace old worn out parts. Otherwise points are fine in a stock engine such as these.
GRX is offline   Reply With Quote
Reply

Bookmarks

Tags
1970 c10, fleetside, straight 6


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:07 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com