My 67 Build Thread - The 1947 - Present Chevrolet & GMC Truck Message Board Network

rickygee · 10-13-2009, 05:01 PM

Ok so here goes i know a lot of these pics are on my intro post but i figure id compile a complete build thread.
Here is the info and a few photos.

What i wanted to do with this particular project was pretty straight forward
I wanted a truck to progressively work on and update as time/budget permitted. However i thought i would go with a backwards approach to this
(get all parts then clean it up)
What i started with was a very clean 1 owner 67 that was driven semi regularly to haul leaves, trash ect.
I purchased the truck very early this year. I drove it around for a couple of weeks stock then began to tear it apart.

So far i have Modified the following from stock

Engine:
Basically a 468 CI LS7
Brodix Race Rite CNC ported Heads.
Comp 297TH Cam
Edelbrock RPM AIR Gap
Old BG Carb I had Laying Around.
Hooker Super comp 2” Headers (good for now, but not so good for ground clearance)

Transmission:
Richmond 6 Speed that my dad took on trade so he donated it.

Rear:
Stock 3.73 with Eaton Posi
Dutchman 5 Lug Axles

Suspension:
Complete Ridetech Strong Arms Kit
this thing is beautiful and a breeze to install.
Early Classic Drop Spindles and Front 5 Lug Disc Kit also a very choice piece.
Ridetech Front Sway Bar
Splined Rear Sway Bar (still in the works)

Tires / Wheels:
The Wheels Are Made By Esajian Wheel Basically a Billet Specialties Apex G
18x8with 4.5 bs in front and 18x10 with 5.5 bs in rear.
I did have to make a small spacer for the rear about .3125" thick per side 5/8" total
Tires are Nitto 555's 295/45/18 and 255/45/18

Other Stuff:
18 Gallon Rick’s Stainless Tank In-tank Electric Pump
Stock Seat Covered in a Nice Thick Black Leather with Red Stitching.

I am going to drive for a wile in its current condition work out all the bugs, and be working on another frame that I will clean up paint and swap all suspension over.
Lastly I will paint the truck but not for a wile…

Very Big Thanks To Everyone who Assisted me with this.
Bret and Tony at Ridetech
Stan at ECE
Rick's Hot Rod Shop.

rickygee · 10-13-2009, 05:03 PM

One More...

LOW DOUGH · 10-13-2009, 05:07 PM

Subscribed! I'm busy working so I will have to read later. Can't wait to see more pics!

rickygee · 10-13-2009, 05:56 PM

One issue i came across was the shifter...
Since i am running the 6 speed it is longer. hence a Stock Hurst Handle will not work it hit the seat just a tad when pushed into 2-4-6-or Reverse it would mash into the seat about 1"
I made a shifter handle that now contours the stock seat about .5" all the way around when in a back Position. In this pic it is in 1st so there is not a huge amount of throw commonly found with truck shifters,and it sits at a nice height it feels just right. The Holes were just something that came up with you really have to see it in person to appreciate it.

One other thing i came across was the factory z bar-
I had to shorten it by 3/8" to get it to fit. ill post more pics of that when the site allows me to.
Thanks!

68GenIII · 10-13-2009, 06:51 PM

That truck is good looking!! I really like the wheels!

OARNGESI · 10-13-2009, 07:13 PM

Truck looks great dont paint it

rickygee · 10-13-2009, 07:22 PM

Quote:

Originally Posted by OARNGESI

Truck looks great dont paint it

yea paint is no where in the near future i just like the way it looks soo much like this for now. its amazing when you wipe the parts down that actually have paint on them they are still shiny.

19673ontree · 10-13-2009, 07:53 PM

this is one of those once in a LONGGGGGGGG while truck's that you see , very very few like this , I'd say you don't even realize how valuable that truck was in the first pic's , I am drooling all over my keyboard as I am sure lot's of other's are too ,it would be amazing to own such a piece but being in one of the auto rust state's I never see them like that , I'd say that a truck like that one did not exist here in southrust Virginia by 1970 ,
THAT IS THE COOLEST NICEST 67 FIND I HAVE SEEN ON HERE !!!!!!!!!!!!!!!

72BlckButy · 10-14-2009, 08:24 AM

Subscribed!

What a great looking project, keep at it!

BigShoe24 · 10-14-2009, 10:21 PM

Sick Shifter Dude!

*Dylan · 10-15-2009, 01:53 AM

Wicked truck, the wheels and shifter look real good. Do you have any side shots with the new wheels on?

franky69c10 · 10-15-2009, 02:03 AM

Subscribed

Mike J · 10-15-2009, 11:06 AM

truck looks awesome brother! good work.

allen123 · 10-15-2009, 11:33 AM

Sick truck, you should just put a shop logo on the said and leave the paint but thats just what i'd do

rickygee · 10-15-2009, 01:30 PM

Thanks Guys I appreciate it... have a ton more photos to upload as soon as the site it repaired.

I am going to order one of these puppies aswell so i can get some Video up too. Unfortunately they are not shipping till later this month.
http://www.goprocamera.com/index.php...2&productid=30

I will be at the Scottsdale Good Guys with it the weekend before Thanks Giving.

Twisted78SS · 10-16-2009, 05:02 PM

Tagging along for the ride.. Truck is looking great!

drasticwagon · 10-21-2009, 08:29 AM

Freaking Sweet Truck!

drasticwagon · 10-21-2009, 08:32 AM

Can you PM me the part number on that Ricks Tank, Thanks.

my67chevytruck · 12-03-2009, 10:39 AM

seet ride.

**67cheby** · 12-03-2009, 11:03 AM

Awesome

C20-67_N_MO · 12-03-2009, 11:19 AM

Quote:

Originally Posted by OARNGESI

Truck looks great dont paint it

ditto x2!!!

I rarely say that about these trucks too. But your's just looks so cool as is it would be a shame to paint it.

Any more updates and progress you can post up for us?

Great looking project!!

rickygee · 12-10-2009, 11:33 PM

Hey Guys well i am getting ready to get back on the project its been a wile since i have done anything with it since work really picked up which is a great thing.
I moved the truck into my shop from my dads because its smaller warmer and better lit.

There is a couple of things i need to do before i fire it and button it up.
Finish plumbing brakes
Make a Shroud and mount fans.
Make a 1" Spacer for the front Bump Stops because my headers will hit if not.

rickygee · 12-10-2009, 11:43 PM

as promised are some pics of the bell crank (z-bar) modifications.
the stock one was about .375" too wide so what i did was cut the existing arms off narrow it, and extend the bore accordingly. i made new arms it worked perfectly. they are .375" thick and at the narrowest point are also .375" thick in the center of the oval. i was a little worried that they would not hold up but i tried crushing it in a 70 ton press brake it took all it had to bend it in a longitudinal direction. imo it had sufficient strength. i used a 3/8" yoke to connect it and made an engagement rod to actuate the clutch fork. i hardened the tip to hold up.

**wancosc356** · 12-10-2009, 11:43 PM

Very nice looking truck. Can't wait to see more.

franky69c10 · 12-11-2009, 04:05 AM

Quote:

Originally Posted by wancosc356

Very nice looking truck. Can't wait to see more.

Yeah what he Said lol

10-13-2009, 05:01 PM	#1
rickygee Registered User Join Date: Sep 2009 Location: El Paso, Texas Posts: 17	My 67 Build Thread Ok so here goes i know a lot of these pics are on my intro post but i figure id compile a complete build thread. Here is the info and a few photos. What i wanted to do with this particular project was pretty straight forward I wanted a truck to progressively work on and update as time/budget permitted. However i thought i would go with a backwards approach to this (get all parts then clean it up) What i started with was a very clean 1 owner 67 that was driven semi regularly to haul leaves, trash ect. I purchased the truck very early this year. I drove it around for a couple of weeks stock then began to tear it apart. So far i have Modified the following from stock Engine: Basically a 468 CI LS7 Brodix Race Rite CNC ported Heads. Comp 297TH Cam Edelbrock RPM AIR Gap Old BG Carb I had Laying Around. Hooker Super comp 2” Headers (good for now, but not so good for ground clearance) Transmission: Richmond 6 Speed that my dad took on trade so he donated it. Rear: Stock 3.73 with Eaton Posi Dutchman 5 Lug Axles Suspension: Complete Ridetech Strong Arms Kit this thing is beautiful and a breeze to install. Early Classic Drop Spindles and Front 5 Lug Disc Kit also a very choice piece. Ridetech Front Sway Bar Splined Rear Sway Bar (still in the works) Tires / Wheels: The Wheels Are Made By Esajian Wheel Basically a Billet Specialties Apex G 18x8with 4.5 bs in front and 18x10 with 5.5 bs in rear. I did have to make a small spacer for the rear about .3125" thick per side 5/8" total Tires are Nitto 555's 295/45/18 and 255/45/18 Other Stuff: 18 Gallon Rick’s Stainless Tank In-tank Electric Pump Stock Seat Covered in a Nice Thick Black Leather with Red Stitching. I am going to drive for a wile in its current condition work out all the bugs, and be working on another frame that I will clean up paint and swap all suspension over. Lastly I will paint the truck but not for a wile… Very Big Thanks To Everyone who Assisted me with this. Bret and Tony at Ridetech Stan at ECE Rick's Hot Rod Shop. Last edited by rickygee; 10-14-2009 at 05:40 PM.

10-13-2009, 05:03 PM	#2
rickygee Registered User Join Date: Sep 2009 Location: El Paso, Texas Posts: 17	Re: My 67 Build Thread One More...

10-13-2009, 05:07 PM	#3
LOW DOUGH I'M TRUCK CRAZY! Join Date: Oct 2006 Location: Sachse, TEXAS Posts: 1,737	Re: My 67 Build Thread Subscribed! I'm busy working so I will have to read later. Can't wait to see more pics!

10-13-2009, 05:56 PM	#4
rickygee Registered User Join Date: Sep 2009 Location: El Paso, Texas Posts: 17	Re: My 67 Build Thread One issue i came across was the shifter... Since i am running the 6 speed it is longer. hence a Stock Hurst Handle will not work it hit the seat just a tad when pushed into 2-4-6-or Reverse it would mash into the seat about 1" I made a shifter handle that now contours the stock seat about .5" all the way around when in a back Position. In this pic it is in 1st so there is not a huge amount of throw commonly found with truck shifters,and it sits at a nice height it feels just right. The Holes were just something that came up with you really have to see it in person to appreciate it. One other thing i came across was the factory z bar- I had to shorten it by 3/8" to get it to fit. ill post more pics of that when the site allows me to. Thanks! Last edited by rickygee; 10-13-2009 at 05:58 PM.

10-13-2009, 06:51 PM	#5
68GenIII Registered User Join Date: Apr 2006 Location: Fort Walton Beach, FL Posts: 257	Re: My 67 Build Thread That truck is good looking!! I really like the wheels! __________________ 68 lwb to swb Cummins swap in the works. I promise it will be cool someday.

10-13-2009, 07:13 PM	#6
OARNGESI Registered User Join Date: Sep 2008 Location: CASA GRANDE AZ Posts: 4,276	Re: My 67 Build Thread Truck looks great dont paint it __________________ 70 SWB STEPSIDE 70 BLAZER 09 challenger

10-13-2009, 07:53 PM	#8
19673ontree CAN'T FIX NOTHIN Join Date: Sep 2006 Location: SOUTHRUST VIRGINIA !!! Posts: 2,112	Re: My 67 Build Thread this is one of those once in a LONGGGGGGGG while truck's that you see , very very few like this , I'd say you don't even realize how valuable that truck was in the first pic's , I am drooling all over my keyboard as I am sure lot's of other's are too ,it would be amazing to own such a piece but being in one of the auto rust state's I never see them like that , I'd say that a truck like that one did not exist here in southrust Virginia by 1970 , THAT IS THE COOLEST NICEST 67 FIND I HAVE SEEN ON HERE !!!!!!!!!!!!!!! __________________ 1967 C10 Shortbed Fleetside Small back glass 6 cyl 3spd on the tree 3.08 gears underdash AC

10-14-2009, 08:24 AM	#9
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: My 67 Build Thread Subscribed! What a great looking project, keep at it! __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

10-14-2009, 10:21 PM	#10
BigShoe24 True Addiction Join Date: Nov 2005 Location: FTL Posts: 415	Re: My 67 Build Thread Sick Shifter Dude! __________________ RCC

10-15-2009, 01:53 AM	#11
*Dylan Mean Buzzin' Half Dozen Join Date: Mar 2008 Location: Orlando, Florida Posts: 1,081	Re: My 67 Build Thread Wicked truck, the wheels and shifter look real good. Do you have any side shots with the new wheels on? __________________ "War is an ugly thing, but not the ugliest of things. The decayed and degraded state of moral and patriotic feeling which thinks that nothing is worth war is much worse. The person who has nothing for which he is willing to fight, nothing which is more important than his own personal safety, is a miserable creature and has no chance of being free unless made and kept so by the exertions of better men than himself." MY TRUCK (Now for sale) 1967 C10 SWB *Dylan* IIMY?

10-15-2009, 02:03 AM	#12
franky69c10 chevy runs deep Join Date: Mar 2006 Location: PHOENIX AZ Posts: 1,074	Re: My 67 Build Thread Subscribed __________________ RAIDER NATION 1969 c10 swb soon 2 b on the road... My LWB is a SWB now http://67-72chevytrucks.com/vboard/s...d.php?t=498241

10-15-2009, 11:06 AM	#13
Mike J vw guy & now c-10 guy Join Date: Sep 2008 Location: Louisville,KY Posts: 483	Re: My 67 Build Thread truck looks awesome brother! good work. __________________ '68 long fleet Finally made some progress on the build!!! My Build Thread

10-15-2009, 11:33 AM	#14
allen123 It'll buff out Join Date: Mar 2008 Location: Blanchard,Ok Posts: 1,376	Re: My 67 Build Thread Sick truck, you should just put a shop logo on the said and leave the paint but thats just what i'd do __________________ 1972 Chevy c10 swb 2008 CBR600RR Grafitti edition My Build Cody Allen

10-15-2009, 01:30 PM	#15
rickygee Registered User Join Date: Sep 2009 Location: El Paso, Texas Posts: 17	Re: My 67 Build Thread Thanks Guys I appreciate it... have a ton more photos to upload as soon as the site it repaired. I am going to order one of these puppies aswell so i can get some Video up too. Unfortunately they are not shipping till later this month. http://www.goprocamera.com/index.php...2&productid=30 I will be at the Scottsdale Good Guys with it the weekend before Thanks Giving.

10-16-2009, 05:02 PM	#16
Twisted78SS Wide n'Low Join Date: Jan 2007 Location: La Center, WA Posts: 1,511	Re: My 67 Build Thread Tagging along for the ride.. Truck is looking great! __________________ Trippin Hazard.. 67 swb, Gold Member.. 68 Suburban Air Force Retired



Register or Log In To remove these advertisements.

10-21-2009, 08:29 AM	#17
drasticwagon Registered User Join Date: Dec 2004 Location: Haslet, Texas Posts: 83	Re: My 67 Build Thread Freaking Sweet Truck! __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=294001

10-21-2009, 08:32 AM	#18
drasticwagon Registered User Join Date: Dec 2004 Location: Haslet, Texas Posts: 83	Re: My 67 Build Thread Can you PM me the part number on that Ricks Tank, Thanks. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=294001

12-03-2009, 10:39 AM	#19
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: My 67 Build Thread seet ride. __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

12-03-2009, 11:03 AM	#20
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: My 67 Build Thread Awesome __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

12-10-2009, 11:33 PM	#22
rickygee Registered User Join Date: Sep 2009 Location: El Paso, Texas Posts: 17	Re: My 67 Build Thread Hey Guys well i am getting ready to get back on the project its been a wile since i have done anything with it since work really picked up which is a great thing. I moved the truck into my shop from my dads because its smaller warmer and better lit. There is a couple of things i need to do before i fire it and button it up. Finish plumbing brakes Make a Shroud and mount fans. Make a 1" Spacer for the front Bump Stops because my headers will hit if not. Attached Images Last edited by rickygee; 12-11-2009 at 12:07 AM.

12-10-2009, 11:43 PM	#23
rickygee Registered User Join Date: Sep 2009 Location: El Paso, Texas Posts: 17	Re: My 67 Build Thread as promised are some pics of the bell crank (z-bar) modifications. the stock one was about .375" too wide so what i did was cut the existing arms off narrow it, and extend the bore accordingly. i made new arms it worked perfectly. they are .375" thick and at the narrowest point are also .375" thick in the center of the oval. i was a little worried that they would not hold up but i tried crushing it in a 70 ton press brake it took all it had to bend it in a longitudinal direction. imo it had sufficient strength. i used a 3/8" yoke to connect it and made an engagement rod to actuate the clutch fork. i hardened the tip to hold up. Attached Images Last edited by rickygee; 12-10-2009 at 11:43 PM.

12-10-2009, 11:43 PM	#24
wancosc356 I Like Mine With No Shine! Join Date: Apr 2009 Location: SC Posts: 2,705	Re: My 67 Build Thread Very nice looking truck. Can't wait to see more. __________________ Michael 1967 Chevrolet C10 Short Fleet (Literal Ground Up....One Day) 2006 GMC Sierra Crew Cab 4x4 1969 Lincoln Continental Coupe Project FOR SALE http://67-72chevytrucks.com/vboard/c...ct=4578&cat=17 1981 Honda CM400 C Bobber SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=384152

Register or Log In To remove these advertisements.