The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-11-2019, 02:13 PM   #1
C101971
Registered User
 
Join Date: Jul 2018
Location: Calgary
Posts: 53
BBC 454 setups

So I'm in the middle of building a mild mark 4 454 for my 71 c10, powerglide, 3:73 gears. I am planning on keeping a stock bottom end, I have picked up remanufactured large oval port heads, not sure what springs are in it but they came off a 500 hp BBC. I was looking into the Edelbrock efi plug and play kit. Comes with efi, intake manifold, distributor, etc. Being as this is a street truck I want to know who has a similar setup and how they like it. I want a roller cam and roller rockers but want to know how it will perform and what brands I should pick before I drop money on it. The truck is driven hard, a choppy idle is always nice, but I'd rather actually go fast then just sound like I can go fast.
C101971 is offline   Reply With Quote
Old 11-11-2019, 10:09 PM   #2
Mike C
Registered User
 
Mike C's Avatar
 
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,723
Re: BBC 454 setups

No input on the EFI, but I have two different 427's. An original L36 390hp from a 69 Corvette .030 over with the L2300 forged pistons that has the smallest Comp Cams hydraulic roller nitrous cam. 224/236 @ .050 113 LSA with 10:1 compression. I plan to install this with a TH200 4R and a set of 3.73 gears in my '69 short step.

The other is a cobbled together 427 with a '76 454 block, GM steel crank, and a set of mildly worked 781 heads that was in a boat. .060 over and L2300 forged pistons. It has a Comp marine hydraulic roller 230/236 @ .050 112 LSA with 8.75:1 compression. This ran 10 mph faster than a 330 hp 7.4l Mercruiser in a 26' boat so realistically 450ish hp. It's going in my Corvette with a McLeod street 5 speed behind it and 3.70 gears.

Both of these cams were chose with the intent of having good street manners. When I bought the nitrous cam the marine cam was my other choice. I stumbled into the second motor which already had the marine cam in it, so I at some point can compare directly. Both cams should be FI friendly.

I have run the former boat motor on my test stand. It sounds wicked and idles quite well at 700 rpm without a transmission attached to it. Should be a hoot in the 3000# 'vette. Now if I can just get my teenagers '72 Jimmy project wrapped up...
__________________
44 Willys MB
52 M38A1
64 Corvette Coupe
68 Camaro 'vert LT1 & TH700
69 Z/28 355 12.6's @110
69 Chevy Short Step 4 1/2"/7" drop
72 Jimmy 4WD 4spd 4" & 35's
02 GMC 2500HD 4x4 Duramax
Mike C is offline   Reply With Quote
Reply

Bookmarks

Tags
454 c10, bbc, cam upgrade, efi, roller cam


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:01 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com