CA Long bed bedside and hood patch panel cuts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ka_jd7and1 · 01-14-2015, 01:41 AM

I have left and right '71 longbed bedsides and a GMC hood that I am going to cut up for patch panels. The bedsides were hit with a forklift when the truck that it was on was being moved. The hood has a couple dents.

These are all California solid metal, surface rust at worst.

I am going to ask $10 per square foot of patch panel, plus shipping to you.

I will post photos tomorrow. If you want to mark them up in a photo editing software or Paint for the areas that you would need, that might be the best way.

Crushkrew · 01-14-2015, 01:10 PM

Hi, I am interested in the sections indicated by the read square in this photo...need to fill those holes...

ka_jd7and1 · 01-17-2015, 08:00 PM

Driver's side:

Has a bow in front section trim bolt hole (pulled out) and squish marks on the bottom

Tail light area also has a gouge

Inside:

ka_jd7and1 · 01-17-2015, 08:05 PM

Passenger side:

Squished part from forklift

Inside

ka_jd7and1 · 01-17-2015, 08:07 PM

Hood:

Dented corner on passenger side

doo142 · 01-18-2015, 09:52 AM

Would you be in to selling rear floor cuts? Need bout 8" of rear edge, thanks

ka_jd7and1 · 01-18-2015, 06:02 PM

Floor and header panel are not for sale, getting put into my truck, sorry.

Will have a wood floor header panel for sale in the future.

64chevtruck · 01-20-2015, 03:07 AM

Hi, Did you still have the passenger bed side available>? Id be interested in the wheel well section out of it if your going to make patch panels from it, Possibly the whole thing now that I look at the pic of mine.....

Thanks

Andy

ka_jd7and1 · 01-21-2015, 04:04 PM

Sure do, have the entire thing still... how much of the wheel well do you need?

These are getting cut up for scrap this weekend minus whatever anyone needs, they have to go.

67ChevyRedneck · 01-24-2015, 02:39 AM

I have a couple of requests...

I definitely need a 6" piece from the lower rear of the DS quarter. Cutting it at the bodyline would be fine, then 8" back from the wheel well should be a safe amount. It looks straight in the pic... is that line just from the trim piece or is there a crease there?

Also, I fubared the back section of my bed (again still driver side), it would be difficult to straighten, but if I could weld in a new section that would be great. I don't need the taillight area, so you could cut it right at the very back of the bed, before it curves around, then right above where the top bodyline starts to roll over, then at the bottom bodyline, to near the wheel well. That is, if it's straight (looks like it is.) Those cuts should leave a somewhat flat panel.

I'd also like a small 1' square piece about an inch above the bodyline on a clean piece somewhere in the middle front section (going to use that for turn signal filler patches, etc)

Again, shipping could be a deal breaker on the bigger piece I want, but I definitely want the smaller quarter wheel well patch if that area is straight and the 1' square piece. Do you have any way to estimate shipping to Taylors, SC?

Also, if it saves money, I can give you my work address for shipping.

67ChevyRedneck · 01-24-2015, 03:00 AM

I'm trying to save a pretty nice straight set of 68 bed sides, I already welded in some wheel well patches from New Mexico... if I can fix THOSE areas I can fix the rest!

67ChevyRedneck · 01-27-2015, 01:59 PM

Bump?

**michael bustamante** · 01-27-2015, 02:52 PM

any cab sections avail?

67ChevyRedneck · 01-29-2015, 04:54 PM

Bump... hoping the OP is checking the forum as a guest? (hasn't logged in since 1-23)

ka_jd7and1 · 03-27-2015, 04:16 PM

Sorry guys, due to some personal circumstances I had to scrap everything.

Nothing left.

01-14-2015, 01:41 AM	#1
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Long bed bedside and hood patch panel cuts I have left and right '71 longbed bedsides and a GMC hood that I am going to cut up for patch panels. The bedsides were hit with a forklift when the truck that it was on was being moved. The hood has a couple dents. These are all California solid metal, surface rust at worst. I am going to ask $10 per square foot of patch panel, plus shipping to you. I will post photos tomorrow. If you want to mark them up in a photo editing software or Paint for the areas that you would need, that might be the best way. __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant

01-14-2015, 01:10 PM	#2
Crushkrew Registered User Join Date: Apr 2011 Location: Ft Liquordale, FL Posts: 138	Re: Long bed bedside and hood patch panel cuts Hi, I am interested in the sections indicated by the read square in this photo...need to fill those holes... Attached Images

01-17-2015, 08:00 PM	#3
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Re: Long bed bedside and hood patch panel cuts Driver's side: Has a bow in front section trim bolt hole (pulled out) and squish marks on the bottom Tail light area also has a gouge Inside: __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant

01-17-2015, 08:05 PM	#4
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Re: Long bed bedside and hood patch panel cuts Passenger side: Squished part from forklift Inside __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant

01-17-2015, 08:07 PM	#5
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Re: Long bed bedside and hood patch panel cuts Hood: Dented corner on passenger side __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant

01-18-2015, 09:52 AM	#6
doo142 Registered User Join Date: Jan 2013 Location: Bristol,In. Posts: 1,118	Re: Long bed bedside and hood patch panel cuts Would you be in to selling rear floor cuts? Need bout 8" of rear edge, thanks

01-18-2015, 06:02 PM	#7
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Re: Long bed bedside and hood patch panel cuts Floor and header panel are not for sale, getting put into my truck, sorry. Will have a wood floor header panel for sale in the future. __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant

01-20-2015, 03:07 AM	#8
64chevtruck Registered User Join Date: Aug 2013 Location: Rochester Wa. Posts: 395	Re: Long bed bedside and hood patch panel cuts Hi, Did you still have the passenger bed side available>? Id be interested in the wheel well section out of it if your going to make patch panels from it, Possibly the whole thing now that I look at the pic of mine..... Thanks Andy Attached Images __________________ 64 C10 Fleetside LB 4 Sp/292 Build http://67-72chevytrucks.com/vboard/s...d.php?t=602438 70 GMC 1500 Fleetside LB 3OT/350 Build http://67-72chevytrucks.com/vboard/s...83#post6767983 76 GMC CCLB Dually Build http://67-72chevytrucks.com/vboard/s...d.php?t=691612 79 GMC 3500 Fleetside LB 454/400 90 Suburban Silverado 4x4 350/700R4 97 1500 Cheyenne Short Fleet 350/5sp

01-21-2015, 04:04 PM	#9
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Re: Long bed bedside and hood patch panel cuts Sure do, have the entire thing still... how much of the wheel well do you need? These are getting cut up for scrap this weekend minus whatever anyone needs, they have to go. __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant

01-24-2015, 02:39 AM	#10
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: Long bed bedside and hood patch panel cuts I have a couple of requests... I definitely need a 6" piece from the lower rear of the DS quarter. Cutting it at the bodyline would be fine, then 8" back from the wheel well should be a safe amount. It looks straight in the pic... is that line just from the trim piece or is there a crease there? Also, I fubared the back section of my bed (again still driver side), it would be difficult to straighten, but if I could weld in a new section that would be great. I don't need the taillight area, so you could cut it right at the very back of the bed, before it curves around, then right above where the top bodyline starts to roll over, then at the bottom bodyline, to near the wheel well. That is, if it's straight (looks like it is.) Those cuts should leave a somewhat flat panel. I'd also like a small 1' square piece about an inch above the bodyline on a clean piece somewhere in the middle front section (going to use that for turn signal filler patches, etc) Again, shipping could be a deal breaker on the bigger piece I want, but I definitely want the smaller quarter wheel well patch if that area is straight and the 1' square piece. Do you have any way to estimate shipping to Taylors, SC? Also, if it saves money, I can give you my work address for shipping. Attached Images __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! Last edited by 67ChevyRedneck; 01-24-2015 at 03:06 AM.

01-24-2015, 03:00 AM	#11
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: Long bed bedside and hood patch panel cuts I'm trying to save a pretty nice straight set of 68 bed sides, I already welded in some wheel well patches from New Mexico... if I can fix THOSE areas I can fix the rest! Attached Images __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!

01-27-2015, 01:59 PM	#12
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: Long bed bedside and hood patch panel cuts Bump? __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!

01-27-2015, 02:52 PM	#13
michael bustamante Senior Member Join Date: Sep 2007 Location: Albuquerque NM Posts: 7,857	Re: Long bed bedside and hood patch panel cuts any cab sections avail? __________________ 1967custom

01-29-2015, 04:54 PM	#14
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: Long bed bedside and hood patch panel cuts Bump... hoping the OP is checking the forum as a guest? (hasn't logged in since 1-23) __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!

03-27-2015, 04:16 PM	#15
ka_jd7and1 is a fungineer Join Date: Jan 2009 Location: Bakersfield, CA Posts: 795	Re: Long bed bedside and hood patch panel cuts Sorry guys, due to some personal circumstances I had to scrap everything. Nothing left. __________________ 2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.