poly motor mounts ? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**crossy** · 07-12-2009, 11:16 PM

do the typical Chevy poly motor mounts work on an 80's chevy truck? I am looking at prothane 'short' mounts, PRT 7-504 for my 81.

I think i have my pinion angle and rear suspension issue solved, but it was brought up to me that the stock column(that I'm keeping), can be putting a lot of undue stress on the tranny case, so I figure I had better start limiting the movement of the engine & tranny. thanx ,crossy

gchemist · 07-13-2009, 07:47 PM

I use poly graphite bushings on my 83. They work great. The motor hardly tilts. The tranny bushing is the same. I upgraded to a two bolt bushing.

**crossy** · 07-13-2009, 10:58 PM

G- do you have the part number of the ones you used? thanx , crossy

454HO · 07-14-2009, 10:04 PM

I'm using Energy Suspension mounts on mine. They are inserts that fit into the stock clamshells.

gchemist · 07-15-2009, 02:35 AM

Quote:

Originally Posted by crossy

G- do you have the part number of the ones you used? thanx , crossy

Here ya go: http://www.p-s-t.com/pc-2481-18-chev...4-1958-93.aspx

You'll love the feel.

07-12-2009, 11:16 PM	#1
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	poly motor mounts ? do the typical Chevy poly motor mounts work on an 80's chevy truck? I am looking at prothane 'short' mounts, PRT 7-504 for my 81. I think i have my pinion angle and rear suspension issue solved, but it was brought up to me that the stock column(that I'm keeping), can be putting a lot of undue stress on the tranny case, so I figure I had better start limiting the movement of the engine & tranny. thanx ,crossy __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-13-2009, 07:47 PM	#2
gchemist BAD BOW-Silverado XST Join Date: May 2000 Location: Senior Member from Austin, TX Posts: 6,431	Re: poly motor mounts ? I use poly graphite bushings on my 83. They work great. The motor hardly tilts. The tranny bushing is the same. I upgraded to a two bolt bushing. __________________ Gerardo a.k.a. Mad Chemist Silverado XST videos

07-13-2009, 10:58 PM	#3
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	Re: poly motor mounts ? G- do you have the part number of the ones you used? thanx , crossy __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

07-14-2009, 10:04 PM	#4
454HO Registered User Join Date: Apr 2005 Location: Austin, TX Posts: 1,224	Re: poly motor mounts ? I'm using Energy Suspension mounts on mine. They are inserts that fit into the stock clamshells. __________________ - Greg



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.