Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
1 Attachment(s)
My initial impression is that these are a great buy.
|
Re: Speed Engineering LS Swap Headers Findings
Yes.They doooo look pretty fricken nice!!.....be sure to post up some pics of what they look like in the chassis!....what mounts planning on using with them?....
|
Re: Speed Engineering LS Swap Headers Findings
Ohh yeah....and which size set did you end up with?.
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
1 Attachment(s)
Here is a pic
|
Re: Speed Engineering LS Swap Headers Findings
Any pic. of the pass. side and how low below the frame do they hang?
|
Re: Speed Engineering LS Swap Headers Findings
I am doing a LS3 / 4L80 in a 1965 c10
|
Re: Speed Engineering LS Swap Headers Findings
These things look awesome.. My bank account would appreciate it if I would stay off this forum! LOL HAHA
|
Re: Speed Engineering LS Swap Headers Findings
bill1969camaro,
It's kind of a bad camera angle, but in the fourth picture I posted you can kind of get an idea of how low they hang. It's been a while since I've looked at it, but I don't believe it hangs down much more than 1/2-3/4" below the frame, if that. Of course I have the 1 3/4 headers, the 1 7/8 may be a bit more. -Zak |
Re: Speed Engineering LS Swap Headers Findings
I bought the shorties - http://www.speed-engineering.com/fea...c10-truck.html .
So nobody runs into the same thing I did, stock plug wires will NOT fit, 3 of them on the driver side are pressed up against the headers. I was going to order the Accell 9000 series ceramic 135degree wires but some reports indicate they are not long enough and pull off the coils. So I ordered the Taylor TAY-76046 from Summit. Will see at end of week if they fit. :metal: the notes for the long tubes indicate they are tight but vendor doesn't have the same warning for the shorties. |
Re: Speed Engineering LS Swap Headers Findings
I have them on my 63 with a t56 and ECE mounts. They fit great. Nice quality for the price.
|
Re: Speed Engineering LS Swap Headers Findings
I instaled the 5.3 in my 65 over the weekend and put the 1 7/8 long tube headers on today, they fit fine. I'm not sure if the following will be of any help to anyone but I'll add it anyway. I used the original V8 stands in the rear position with ICT Billet mounts from eBay. The mounts are in the second position from the rear of the adapters. This allowed my trans mount to match my crossmember location because I didn't want to mess with the driveshaft length. I had the driveshaft shortened in 2001 when I changed to a 700R4. The only problem this has created that I've found so far is the rear coil on the passenger side hits the firewall, not the end of the world. The drivers side has a ton of room but the primary for cylinder #4 is about 1/4" from the frame. The ground clearance is higher than when I had long tubes on the ZZ4 I pulled to the 5.3.
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
Anything specific you want a picture of?
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
I'll have to take a side view next week when I put my engine back in, the cam retention plate was creating oil pressure issues. I hope to pick it up from the machine shop Monday.
|
Re: Speed Engineering LS Swap Headers Findings
2 Attachment(s)
Attachment 1610561
Attachment 1610562[ QUOTE=PowerdbyChevy79;7824749]of how the headers fit...[/QUOTE] |
Re: Speed Engineering LS Swap Headers Findings
1 Attachment(s)
This kind of gives an idea of how they hand down, the trans X member is in the foreground.
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
Re: Speed Engineering LS Swap Headers Findings
Anyone have pics of plug wires that clear the primaries? And which ones they used?
|
Re: Speed Engineering LS Swap Headers Findings
Those collectors look like they're pointed directly at the trans crossmember. Did you have any problems routing the exhaust?
|
Re: Speed Engineering LS Swap Headers Findings
Quote:
|
All times are GMT -4. The time now is 12:59 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com