The 1947 - Present Chevrolet & GMC Truck Message Board Network

Page 3 of 3

Show 40 post(s) from this thread on one page

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- Blazer and Suburban Stuff (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=199)

- - GA Suburban rear half part out/cuts (https://67-72chevytrucks.com/vboard/showthread.php?t=779432)

Madkidd007

10-11-2019 12:39 PM

Re: Suburban rear half part out/cuts

TtT

ajgriffin

10-13-2019 03:16 AM

Re: Suburban rear half part out/cuts

I didn't see it, but curious if you have the driver's wheel well? I need the front flange off it so I can patch it onto my passenger rear wheel well where the spare would normally go.

Madkidd007

10-13-2019 03:38 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by ajgriffin (Post 8608593)

I didn't see it, but curious if you have the driver's wheel well? I need the front flange off it so I can patch it onto my passenger rear wheel well where the spare would normally go.

I just went outside and looked, it is eat up. Unless you can make the flange that goes between the tubs work I don’t have anything to help

ajgriffin

10-15-2019 02:01 AM

Re: Suburban rear half part out/cuts

1 Attachment(s)

Quote:

Originally Posted by Madkidd007 (Post 8608595)

I just went outside and looked, it is eat up. Unless you can make the flange that goes between the tubs work I don’t have anything to help

I'm guessing you're talking about the section of the tub that runs front to back? I need a piece that will go here. Its about 2" tall and 11" wide. What do you think?

Attachment 1949760

Madkidd007

10-15-2019 03:58 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by ajgriffin (Post 8609729)

I'm guessing you're talking about the section of the tub that runs front to back? I need a piece that will go here. Its about 2" tall and 11" wide. What do you think?

Attachment 1949760

You are correct on the front to back piece. If you compare to your tub in the picture and looks like the front to back section will work. I’ll remove the wood and check the condition on the tub I have

Madkidd007

10-27-2019 12:17 PM

Re: Suburban rear half part out/cuts

It’s an old thread with old parts, but still have them stashed behind the house.

Madkidd007

11-13-2019 05:27 PM

Re: Suburban rear half part out/cuts

2 Attachment(s)

For mrweld. What’s left

mrweld

11-14-2019 09:10 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by Madkidd007 (Post 8626516)

For mrweld. What’s left

those will work fine, just need the sheet metal if you need the rest

Madkidd007

11-14-2019 09:29 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by mrweld (Post 8626834)

those will work fine, just need the sheet metal if you need the rest

So if I finished the vertical cut to the top so they are a lot smaller to ship would that work? Say $20 a side plus $20 for shipping & PayPal’s fee, $60 all in to your door? If so just use my paypal below and I’ll get them cut when I wake up this afternoon.

mrweld

11-14-2019 09:55 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by Madkidd007 (Post 8626843)

I have a big rust hole in top, I will need them as pictured. I think that will cover it

Madkidd007

11-14-2019 10:08 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by mrweld (Post 8626848)

I have a big rust hole in top, I will need them as pictured. I think that will cover it

I’ll do some weights and measuring later then

mrweld

11-14-2019 10:14 AM

Re: Suburban rear half part out/cuts

Quote:

Originally Posted by Madkidd007 (Post 8626856)

I’ll do some weights and measuring later then

ok thanks

Madkidd007

11-16-2019 06:37 PM

Re: Suburban rear half part out/cuts

1 Attachment(s)

These are gone. Few pieces left if anyone could use something make an offer

All times are GMT -4. The time now is 08:33 PM.

Page 3 of 3

Show 40 post(s) from this thread on one page