Re: Walter DeWayne...Walt for short
1 Attachment(s)
I decided not to wait & got the transmission in place too. Now, me & my sore back are going in for the night. :lol:
|
Re: Walter DeWayne...Walt for short
After a bunch of tweaking and measuring, I’ve concluded that the BBC sits entirely to low in the chassis to fit any kinda manifolds or headers. It sits about an inch lower than it did in the camper chassis. The mounts seem to be for a SBC vs a BBC?
|
Re: Walter DeWayne...Walt for short
Ruh roh
|
Re: Walter DeWayne...Walt for short
1 Attachment(s)
Quote:
If it won't work... I'll snatch the BBC out and put the fresh SBC out of Vern into this chassis and put the BBC in Vern. The ole swap'O'Roo. |
Re: Walter DeWayne...Walt for short
Well, I haven't heard back from Nate, but I found a post from Nate in 2007 that states, " The BBC tabs are just over 1/2" taller than the SBC tabs. So, you can run a SBC with the tabs for a BBC, but not the other way around". But then in 2014 he stated that for the Mild DM, the SBC and BBC tabs are the same...that was me that asked the question back then. I don't think that was the correct answer. So, now I know I've got SBC tabs instead of BBC. I hope to get an answer soon, so I'll continue to wait to hear back from PB.
|
Re: Walter DeWayne...Walt for short
1 Attachment(s)
I finally got the rearend bag mounts welded in place and had it blasted and powdercoated.
|
Re: Walter DeWayne...Walt for short
Ever hear from Nate? The diff came out nice.
|
Re: Walter DeWayne...Walt for short
Hey Doug,
I did hear back, but don’t have a remedy yet. I’ve sent him quite a few pictures of the chassis & motor (& it’s orientation). He’s going to design/make a set of motor mount plates that'll raise the current setup about 5/8”. That should be plenty, or so I hope. But he said it’d be a week or so before he’d have time to draw them up and such. We’ll see how it goes. |
Re: Walter DeWayne...Walt for short
Well, still no solid word from Nate. I’m really pretty disappointed in the lack of give-a-$h!T. I can do a lot of things but chassis/motor metal fab stuff on a planned out setup ain’t my game. But, I guess I’m going to have to figure it out.
On another note, I sold my 77 C10 so I’m going to be more focused on this build again...hopefully until the end this time. I’ve gotten the rearend housing back from powdercoat and I’ll be assembling and setting up the gears and Eaton Posi this weekend. I decided to go 3.42’s instead of 3.73’s since the BBC/700r4 should be good with a lower rpm functioning range. |
Re: Walter DeWayne...Walt for short
4 Attachment(s)
No word from Nate, but I did get the rearend back from my buddy. Eaton posi and new 3.42 gears done! I did some checking & cleaning tonight, but tomorrow I’ll try like He77 to get it completely assembled.
|
Re: Walter DeWayne...Walt for short
1 Attachment(s)
Not a lot of pictures but I got the rearend mostly assembled. Somehow I lost the d@mn C-clips, so I had to order some but they should be here tomorrow. I got everything else done and stuck it under the chassis.
Here’s a pic to prove I’m progressing. If I ever get the correct engine mounts, I’ll fit the exhaust. Then.... I’ll get the fuel lines, tranny lines, brake lines and airlines routed and fit the cab and frontend. After that, blow it apart & powdercoat, paint and such. |
Re: Walter DeWayne...Walt for short
3 Attachment(s)
Well, finally got it on the ground. I just ran airlines to a shrader valve for fronts & back. But it has wheels on it to give me an idea of how it’ll sit. I did figure out that the shocks I have are all 4 for the front so I made a call and have the correct rears on the way. But they don’t affect these pictures.
|
Re: Walter DeWayne...Walt for short
2 Attachment(s)
Comparison...down & up.
|
Re: Walter DeWayne...Walt for short
Cool. That thing is LOW.
|
Re: Walter DeWayne...Walt for short
Quote:
|
Re: Walter DeWayne...Walt for short
Looks good. Your raised height... is that going to be your ride height?
|
Re: Walter DeWayne...Walt for short
Quote:
|
Re: Walter DeWayne...Walt for short
Looks like it going to sit nice with plenty of good ground clearance.
|
Re: Walter DeWayne...Walt for short
2 Attachment(s)
I got a little bit done today. Got the PB tank/compressor mounts located and bolted up.
|
Re: Walter DeWayne...Walt for short
1 Attachment(s)
I also finalized my EFI decision today and ordered the Holley Sniper 550-511 system.
|
Re: Walter DeWayne...Walt for short
Quote:
|
Re: Walter DeWayne...Walt for short
1 Attachment(s)
Time for a test fit of the body to check out fitment.
|
Re: Walter DeWayne...Walt for short
Subbed. Build looks good so far man. Glad to see you kept the truck and started this thread :metal:
|
Re: Walter DeWayne...Walt for short
Quote:
|
Re: Walter DeWayne...Walt for short
2 Attachment(s)
I got some time to work on it this morning. So, I got the stock chassis moved out of the way and tucked the Porterbuilt chassis under Walter. Motor & transmission seem to clear just fine. The inner fenders are the only problem I ran into today...they hit the shocks, but I "clearanced" them to fit, but the 18" tires hit the inner fender about 2" before full bottom. So now I've got to figure out what inner fenders I can use and keep the stock style hood hinges as I have a pretty pricey set of billet hinges on the shelf for Walter...
|
All times are GMT -4. The time now is 03:39 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com