![]() |
Walter DeWayne...Walt for short
5 Attachment(s)
Hey All,
Thought I'd introduce my new aquisition and preface this build thread with the fact that I really won't get much done to it until the weather breaks here in the MUGGY south, but I wanted to start the thread on day 1. Truck... 1968 2wd Custom SWB Fleet. 283 (?), 3 OTT, open diff rear. Options are few...push button radio, chrome front & rear bumpers, and side trim is about all I can make out on the SPID. Original paint, motor, trans, hubcaps, wheels etc. You get the jist. Plan... 5.3/4L60e with CTSV oil pan, PSI harness and reflashed ECU, Jeep Wrangler rear tank with A/C Delco EFI pump and s/s fuel lines rear to front, Painless harness, Inlinetube stainless hardlines and s/s braided hard to caliper & rear lines, PB Mild front Dropmember, PB rear Mild/Touring rear dropmember with PB tubular rear trailing arms, PB crossmembers, bags, Staggered 18" Boss 338's, Wilwood 14" 6-piston fronts & Wilwood 13" rear brakes, built '70-72 12 bolt (Eaton diff, 3.73's), Wilwood M/C and p/v... I ALREADY HAVE THESE PIECES SO I WILL BE USING THEM :). I have lot's of other parts, but dang if I can remember them... Wish list includes A/C, power windows & locks, scuff & clear the paint and drive the heck out of ole Walt. |
Re: Walter DeWayne...Walt for short
5 Attachment(s)
More pics...
|
Re: Walter DeWayne...Walt for short
Pretty cool project..Thanks for the pictures
|
Re: Walter DeWayne...Walt for short
I can dig it, It looks like a great ole truck.
Subbed. |
Re: Walter DeWayne...Walt for short
I forgot the back story...
Bought it from the Grandson of the original owner (named Walter DeWayne "last name")...hence the inevitable name of the project. Last time Walter drove Walt was in 1984, the truck has literally been sitting in a "barn" since then. Move forward to 2014 and Grand Father died and grandson inherited the property and wasn't keen on ole Walt, so I scored him. I have the original bill of sale, books, pamphlets etc. Did I mention that I'm STOKED!!! |
Re: Walter DeWayne...Walt for short
Great looking truck! sounds like you have some good plans for it..
|
Re: Walter DeWayne...Walt for short
Not a lot of rust it looks like. SPID seen better days.
|
Re: Walter DeWayne...Walt for short
Id kill to find a truck with that patina. Lucky !
|
Re: Walter DeWayne...Walt for short
Quote:
|
Re: Walter DeWayne...Walt for short
Very cool truck Ed.
And you have some sweet plans for it. |
Re: Walter DeWayne...Walt for short
Quote:
Quote:
Quote:
Quote:
Quote:
|
Re: Walter DeWayne...Walt for short
Nice looking truck, can't wait to see the transformation
|
Re: Walter DeWayne...Walt for short
OMG. OMG. Good Buy!
|
Re: Walter DeWayne...Walt for short
Quote:
Quote:
|
Re: Walter DeWayne...Walt for short
I've tentatively made an order for PB stuff from one of our board vendors. Mild front dropmember, tubular upper & lower control arms, trans crossmember, trailing arms & crossmember, R&P, front shock relocation brackets & 3 joint steering shaft.
|
Re: Walter DeWayne...Walt for short
PB trailing crossmember bought here on the site today. I need a mild md and trailing arms and I'm ready. Whoop whoop
|
Re: Walter DeWayne...Walt for short
Well, I got all the front PB dropmember stuff bought today from a member on here. Now all I need is a set of PB trailing arms & I'm set. Anybody :D ?
|
Re: Walter DeWayne...Walt for short
Nice parts pickup, you doing mild dropmembers front and rear?
|
Re: Walter DeWayne...Walt for short
No, in the rear I'm only going with the 2 piece notch, so very mild drop in the rear. If, by some chance, I could find the mild rear notch & bridge, I'd go that route though.
|
Re: Walter DeWayne...Walt for short
Nice score! I'll be following along. I like your plans, should be great when it's done.
|
Re: Walter DeWayne...Walt for short
this should be good, especially with the list of parts you mentioned.
|
Re: Walter DeWayne...Walt for short
And I got the PB trailing arms ordered this morning from member "LaidBackRecreations". I think that's all I need...at least for awhile :lol:
|
Re: Walter DeWayne...Walt for short
1 Attachment(s)
Well, it's been awhile since I've done anything related to ole Walt because of the newest acquisition, Chubby. But I did get over to the Fastenal store and pick up my PB front dropmember pieces & parts. Looks like everything is there, but the balljoints and CPP modular spindles aren't the '73 up pieces I was told :(, so I guess I'll have to sell the spindles and buy new balljoints. I'm going to use my McGaughy big brake spindles as I don't need the extra narrow"ness" of the CPP spindles with the 1" narrower PB control arms. I was going to use them on another project, but oh well.
Just a funny picture of my pickup vehicle... My wife drove my truck to work today, so I made do :metal: |
Re: Walter DeWayne...Walt for short
All I'm waiting on is my trailing arms and I'll be PB equipped. Then I'll start tearing into Walt.
|
Re: Walter DeWayne...Walt for short
PLEASE don't paint it!
|
All times are GMT -4. The time now is 02:14 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com