![]() |
UXDesigner's 1967 C10 - The Keeper
Well folks, it took only 7 months after selling my previous build to get back in the game. I'm more motivated than ever and looking forward to building a truck that's a "keeper" based on what I learned from the previous build and all of you! A bit delayed on the progress so I'll start with a quick summary to get us to where the build stands to date.
July 15th, 2016 http://stickyxd.com/c10/67/IMG_6552.jpg http://stickyxd.com/c10/67/IMG_6556.jpg http://stickyxd.com/c10/67/IMG_6554.jpg http://stickyxd.com/c10/67/IMG_6661.jpg http://stickyxd.com/c10/67/IMG_6566.jpg http://stickyxd.com/c10/67/IMG_6652.jpg http://stickyxd.com/c10/67/IMG_6654.jpg http://stickyxd.com/c10/67/IMG_6568.jpg http://stickyxd.com/c10/67/IMG_6565.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Researched many color combos for hours but ultimately decided on a pearl red and pearl white two tone. Its a classic paint scheme but I wanted to mix it up a bit with the pearl white as the accent and no white top.
http://stickyxd.com/c10/67/paintScheme_Red.png |
Re: UXDesigner's 1967 C10 - The Keeper
|
Re: UXDesigner's 1967 C10 - The Keeper
Shoes must go on first!
Foose Legend Front - 20x8.5 (255/35/20) Rear - 20x10 (275/35/20) http://stickyxd.com/c10/67/051439EF-...16DD714F43.jpg http://stickyxd.com/c10/67/16ED3B0C-...363B9DFACF.jpg http://stickyxd.com/c10/67/CA54FB5E-...92B1B81A00.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Good Choice !
|
Re: UXDesigner's 1967 C10 - The Keeper
I had great success with the CPP's products on my last build so I went ahead and used the same. I upgraded to the headers instead of the TBSS manifolds and I'm really happy I did. Clearance is excellent and the sliders make the install super simple with the 4L60e.
Doug Thorley Headers (THY-322Y-C) CPP Tubular Motor Mount Perches (6372MP-SM) CPP Tubular Transmission Crossmember (CP9427) Poly Tranny Pad (3-1108G) Poly Motor (3-1114G x2) http://stickyxd.com/c10/67/00F5583D-...508C2B5D6B.jpg http://stickyxd.com/c10/67/E84FFDE6-...B09385F40C.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
For the fuel system I decided on the Aeromotive 18688 Phantom 340 Fuel Pump System. It's a bit more expensive than the typical external pump setup but the amount of time I saved alone was worth it. The truck already had the aluminum fuel tank relocated to the rear so it was as simple as cutting the hole (template provided) dropping it in and running the wires and fuel lines. For the fuel lines I kept it simple. I once again used the Russel Pro Classic braided fuel line, AN fittings at every connection and a stock fuel filter on the frame rail.
http://stickyxd.com/c10/67/9C464ED6-...9E7AF1DEEE.jpg http://stickyxd.com/c10/67/AFF98952-...F8F5E9D13A.jpg http://stickyxd.com/c10/67/FA306BAB-...199C798800.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
The fuel pedal was a challenge, the engine I picked up did not come with the TAC or the fuel pedal so I searched around and ended up finding one on ebay. The listing even included the bracket which made the really easy. If you plan on doing a DBW fuel pedal, make sure you get the bracket. Only requires a simple bend on the lower tab of the bracket to match the cab floor angle, a few spacers (i used screw nuts) and drilling the new holes in the firewall and floor.
http://stickyxd.com/c10/67/s-l1600.jpg http://stickyxd.com/c10/67/83493B41-...663C093572.jpg http://stickyxd.com/c10/67/73C767E0-...6C60CF8D85.jpg http://stickyxd.com/c10/67/CA9E1604-...F094F23184.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
The truck came with a very nice Flaming River tilt column and the power steering conversion was complete and fully functional. I didn't want to mess with converting to a column shift so I went with a new short 4L60e shifter kit and I'm really happy with it. I still need to weld up the hole for the aftermarket emergency brake that I don't plan on using.
http://stickyxd.com/c10/67/5E84F82B-...A6FE161842.jpg http://stickyxd.com/c10/67/59FC7889-...AC47D6A982.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
|
Re: UXDesigner's 1967 C10 - The Keeper
I did not think the LS would run that smooth without the MAF hooked up.
Did you have the O2 hooked up? Aluminum heads heat up pertty fast, did you have any water in the block? |
Re: UXDesigner's 1967 C10 - The Keeper
Looks like a great start.
|
Re: UXDesigner's 1967 C10 - The Keeper
Quote:
|
Re: UXDesigner's 1967 C10 - The Keeper
I'm watchin.
|
Re: UXDesigner's 1967 C10 - The Keeper
Received all new Mar-K chrome trim this weekend, well packaged and quality is excellent.
http://stickyxd.com/c10/67/12F3DE66-...B9D46B56B1.jpg http://stickyxd.com/c10/67/611837D5-...B5C917E4BA.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Stock auto transmission cooling lines snap right into the radiator with these adapters, Simple install, lines only needed a couple of bends.
http://stickyxd.com/c10/67/0E0E87C5-...F79D309122.jpg http://stickyxd.com/c10/67/515F3318-...A35DEF37E3.jpg http://stickyxd.com/c10/67/48A12376-...D34269975F.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Mar-K gotta be one of the best places I've ever talked to and/or ordered from.
|
Re: UXDesigner's 1967 C10 - The Keeper
Mar-K has a lot of my money !!
|
Re: UXDesigner's 1967 C10 - The Keeper
The long process of sanding, welding and body work begins. Looks like the PO sprayed paint directly on new reproduction metal without primer. Paint literally peeled off in chunks with compressed air.
April 22, 2017 http://stickyxd.com/c10/67/3C21A47C-...11E7221FF9.jpg http://stickyxd.com/c10/67/0C93F6F2-...6B8F591B5A.jpg June 3, 2017 http://stickyxd.com/c10/67/1F210E8C-...C715D55CCB.jpg http://stickyxd.com/c10/67/2545BFFB-...B194F6E1FB.jpg http://stickyxd.com/c10/67/3706C2AB-...B1D8260CE0.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Awesome build !!! Look forward to more updates and I love the color scheme and choice :chevy:
|
Re: UXDesigner's 1967 C10 - The Keeper
Like Larry said, looks like a great project! It is better the second time around, isn't it? :)
I thought I had heard of Rocklin; I have family in Roseville! Rode the motorcycle out there two years ago. Plan to do that same trip in the '68 when I get it done. Hopefully August 2018 will be the time frame. When I get out that way maybe I can catch you at a cruise in. Subscribing to your thread to watch and maybe learn something from you. The more ideas the merrier. |
Re: UXDesigner's 1967 C10 - The Keeper
Well the good thing about that kind of peel is that it's less troublesome on the sanding joints lol
|
Re: UXDesigner's 1967 C10 - The Keeper
I like the plan, subscribed.
|
Re: UXDesigner's 1967 C10 - The Keeper
Started cleaning up the firewall and front frame. Worked on getting the wire fuel pedal grommet hole correctly sized. Plan on epoxy priming the firewall soon to get the engine back in and space back in the garage to get paint started.
http://stickyxd.com/c10/67/4E43BE09-...49A29F61B3.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Managed to get the firewall and front end frame epoxy primed.
http://stickyxd.com/c10/67/795FD404-...9CFA283512.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Success! I had failed several times over the past few weeks to get the dreaded rear broken exhaust manifold bolt. I read here that the trick was to crank up the volts on the welder and I finally managed to get some metal to stick. The nut I welded on fell off after the first turn but there was just enough metal to use the vise grips and it finally came out.
http://stickyxd.com/c10/67/8E83D5F8-...BD07E6CB44.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Engine back in for hopefully the final time. Installed the headers with gaskets, O2 sensors, new water pump and cleaned up the front of the engine in the process. Also worked on wiring the battery, the truck had a dual rear battery setup when I purchased it so it works out perfect for the new engine as I plan on running the stock air cleaner setup. Of course I had to start it up and hear the rumble to keep up the motivation.
http://stickyxd.com/c10/67/engine1.jpg http://stickyxd.com/c10/67/engine2.jpg http://stickyxd.com/c10/67/engine3.jpg http://stickyxd.com/c10/67/engine4.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Radiator installed, all lines tested for leaks with success. I originally thought about using the factory intake / box but it didn't look as clean as I had imagine and the fabrication to make it sit properly would be significant. I scrapped the idea and decided to go with an aftermarket SPECTRE 9900 Cold Air Intake System for ease of installation and I think the chrome gives the engine compartment a nice touch.
http://stickyxd.com/c10/67/DB4FEF01-...50096EB4AE.JPG http://stickyxd.com/c10/67/BF97D6EA-...EBCD1939B4.JPG http://stickyxd.com/c10/67/B395379D-...22483B0182.JPG Also started drilling all the holes for the trim, took a lot longer than I thought but the pieces were great quality and fitment only needed a few tweaks. http://stickyxd.com/c10/67/2C020749-...60CF3FDFD5.jpg http://stickyxd.com/c10/67/27131902-...362BC0E49C.JPG http://stickyxd.com/c10/67/404DC541-...04D847E919.jpg Managed to get the front grill in epoxy and 2k to test gun settings and pressure as I prepare to paint in the next few weeks. http://stickyxd.com/c10/67/0CA0E6A7-...C6BECA9866.JPG http://stickyxd.com/c10/67/34EA6543-...6698D14353.JPG |
Re: UXDesigner's 1967 C10 - The Keeper
Repaired lower door speaker holes. I admire you folks that weld entire bedsides, its a lot of work. I'm sure my novice welding skills have something to do with the excessive grinding but at least another task is behind me.
http://stickyxd.com/c10/67/0336311A-...BF83D1AAA6.JPG http://stickyxd.com/c10/67/28384728-...B39462B195.JPG http://stickyxd.com/c10/67/71D0ABE4-...080AF0478D.JPG http://stickyxd.com/c10/67/83F2754B-...FEF43CF32A.JPG http://stickyxd.com/c10/67/4C600589-...B469E895F9.JPG http://stickyxd.com/c10/67/5770DF5A-...CDAD605035.JPG |
Re: UXDesigner's 1967 C10 - The Keeper
Also got the front fenders and hood in epoxy, I'm happy with the body work so far but still more work to do.
http://stickyxd.com/c10/67/D1D2BACF-...1E2CDDAEF8.JPG http://stickyxd.com/c10/67/A0A262AC-...08371B154C.JPG http://stickyxd.com/c10/67/81E9647E-...1759116D46.JPG http://stickyxd.com/c10/67/C4A143AA-...788D14F2E4.JPG |
Re: UXDesigner's 1967 C10 - The Keeper
Cool build.
|
Re: UXDesigner's 1967 C10 - The Keeper
Quote:
|
Re: UXDesigner's 1967 C10 - The Keeper
I needed a new glove box door and came across one in excellent condition with a unique SPI sticker and options. Posting in case others are interested in unique truck options.
http://stickyxd.com/c10/67/66A5B366-...C6D93EA111.JPG I originally planned on using a floor shifter but after installation I just didn't like the look and feel of a truck with a floor shifter. Ended up getting a new column shifter which resulted in new steering u-joint work but overall I'm really happy with the end product. http://stickyxd.com/c10/67/1637B431-...FEA5DAF2B3.JPG http://stickyxd.com/c10/67/A591A51C-...9592B9396C.JPG I went for a test drive in the neighborhood to test steering and overall functionality and I ran into an issue with losing complete power and overall responsiveness to my gas pedal when mildly punching it. After checking the TAC, I realized I had a 2006 TAC and gas pedal on the 2003 engine which was causing issues. I had a spare TAC and pedal from a 2003 with the correct TAC numbers and just like that no issues. I even tried the 2006 pedal with the 2003 TAC because it fits better and again no codes or issues. http://stickyxd.com/c10/67/68037575-...2BBD5E3CC9.JPG http://stickyxd.com/c10/67/AA426148-...9DF80F297E.JPG http://stickyxd.com/c10/67/62F21AF8-...25F53E9FDC.JPG |
Re: UXDesigner's 1967 C10 - The Keeper
Got the cab in epoxy, continuing to make progress
http://stickyxd.com/c10/67/872311B7-...6D3D2942B4.JPG http://stickyxd.com/c10/67/9EB4C169-...AF3E00BA27.JPG http://stickyxd.com/c10/67/E3678CE3-...176865C575.JPG http://stickyxd.com/c10/67/3EED9730-...E8E94CBE71.JPG Paint is in, color really looks good in the sun http://stickyxd.com/c10/67/CFACB031-...E7BF75513F.JPG Started work on the bed, filling in the bed stake holes. Feeling more confident with the welder and decided to try and lay a few beads down. http://stickyxd.com/c10/67/F28A2F7E-...267A187712.JPG |
Re: UXDesigner's 1967 C10 - The Keeper
Interior of cab and misc red only parts in paint.
http://stickyxd.com/c10/67/74633C7B-...4723FB8FCD.JPG http://stickyxd.com/c10/67/3D395B73-...CB3BF40C28.JPG http://stickyxd.com/c10/67/D77F97E8-...8CB06F6681.JPG http://stickyxd.com/c10/67/45B1E9F3-...E82C70D984.JPG http://stickyxd.com/c10/67/16765927-...7C89DC1739.JPG http://stickyxd.com/c10/67/075FF1DBA...BA44E8419A.JPG http://stickyxd.com/c10/67/DD313041-...060EE4D2F0.JPG http://stickyxd.com/c10/67/A6BE4EDC-...5E4BF8ACF8.JPG http://stickyxd.com/c10/67/94D8A464-...9D1077DD7A.JPG http://stickyxd.com/c10/67/DC0D2D6D-...111A5A38A8.JPG http://stickyxd.com/c10/70/8E48E1FA-...EA1BB5B9AC.jpg |
Re: UXDesigner's 1967 C10 - The Keeper
Looks like its going to turn out slick. Keep us updated.
|
Re: UXDesigner's 1967 C10 - The Keeper
Quote:
|
Re: UXDesigner's 1967 C10 - The Keeper
Masked off the pearl white areas of the two-tone paint scheme. A lot of work! I underestimated the amount of time and patience it would take to get the lines correct and sealed. The pearl white was a tri-coat and I was intimidated to spray at first but it ended up not being difficult at all.
http://stickyxd.com/c10/67/F6CB7635-...D834BFB4FE.JPG http://stickyxd.com/c10/67/96CB01C1-...0CDE7648B9.JPG http://stickyxd.com/c10/67/F35CCA9B-...1201156CC7.JPG http://stickyxd.com/c10/67/3A126891-...003983A63A.JPG http://stickyxd.com/c10/67/1155CFCB-...AF7E5E6404.JPG |
Re: UXDesigner's 1967 C10 - The Keeper
Pearl will be a nice combo with that red.
|
All times are GMT -4. The time now is 08:43 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com